Search found 17 matches
| Author | Message |
|---|---|
 Topic: WRT54G2 v1 stops working every few days and need to reset |
|
| Nuwanda Replies: 11 Views: 8466 |
 Forum: Broadcom SoC based Hardware Posted: Fri May 21, 2010 18:51 Subject: WRT54G2 v1 stops working every few days and need to reset |
| More info: * The ping doesn't actually timeout, but it reports that 192.168.1.1 is not accessible (as well as any other IP). * The wi-fi broadcast seems to be working, but when I try to connect, I ge ... |
|
 |
|
| Topic: WRT54G2 v1 stops working every few days and need to reset |
|
| Nuwanda Replies: 11 Views: 8466 |
Forum: Broadcom SoC based Hardware Posted: Thu May 20, 2010 0:53 Subject: WRT54G2 v1 stops working every few days and need to reset |
No good  The problem persists after all these changes...Any other suggestion? |
|
|
|
| Topic: WRT54G2: Wireless rate drops to 2 Mbps or 1 Mbps |
|
| Nuwanda Replies: 216 Views: 280134 |
Forum: Broadcom SoC based Hardware Posted: Tue May 18, 2010 11:53 Subject: WRT54G2: Wireless rate drops to 2 Mbps or 1 Mbps |
| I have a WRT54G2v1 with a BCM5354 rev 3, and I experience the wireless rate dropping too. The suggestion of downgrading to SP1 is not an option for me, as older versions have [url=http://www.dd-wrt.c ... |
|
|
|
| Topic: WRT54G2 v1 stops working every few days and need to reset |
|
| Nuwanda Replies: 11 Views: 8466 |
Forum: Broadcom SoC based Hardware Posted: Tue May 18, 2010 11:47 Subject: WRT54G2 v1 stops working every few days and need to reset |
| I had to reset the router again, so just lowering the power and disabling WMM support was not enough. I now applied all the suggestions by raingate (except DNSMask for DNS), let's see how it goes... ... |
|
|
|
| Topic: WRT54G2 v1 stops working every few days and need to reset |
|
| Nuwanda Replies: 11 Views: 8466 |
Forum: Broadcom SoC based Hardware Posted: Sun May 16, 2010 23:20 Subject: WRT54G2 v1 stops working every few days and need to reset |
| OK, I set TX power to 25 mW and disabled WMM support. Frame Burst and Afterburner were already disabled by default. If the problem persists, I'll try disabling CTS Protection Mode, ttraff and the re ... |
|
|
|
| Topic: WRT54G2 v1 stops working every few days and need to reset |
|
| Nuwanda Replies: 11 Views: 8466 |
Forum: Broadcom SoC based Hardware Posted: Sat May 15, 2010 19:32 Subject: WRT54G2 v1 stops working every few days and need to reset |
| Thanks for the reply. Put 12548 on that router and troubleshoot from there. Done. Those are crappy routers with poor signal. Decrease the tx. I don't understand why poor wireless signal in a router ... |
|
|
|
| Topic: WRT54G2 v1 stops working every few days and need to reset |
|
| Nuwanda Replies: 11 Views: 8466 |
Forum: Broadcom SoC based Hardware Posted: Sat May 15, 2010 16:36 Subject: WRT54G2 v1 stops working every few days and need to reset |
| Added more info to the first post... | |
|
|
| Topic: WRT54G2 v1 stops working every few days and need to reset |
|
| Nuwanda Replies: 11 Views: 8466 |
Forum: Broadcom SoC based Hardware Posted: Fri May 14, 2010 23:50 Subject: WRT54G2 v1 stops working every few days and need to reset |
| Hi. Ever since I switched to DD-WRT, I have had to reset (unplug, re-plug) the router every few days. At first, there was ***This is not true now, see edit below*** I have tried enabling remote log ... |
|
|
|
| Topic: Problems after PPPoE remote disconnection |
|
| Nuwanda Replies: 6 Views: 4792 |
Forum: Broadcom SoC based Hardware Posted: Tue Jun 30, 2009 2:56 Subject: Problems after PPPoE remote disconnection |
Well, after a whole week of using build 12188, I haven't had a single problem  :DThank you very much!! I believe the Peacock thread should be updated so this (or another) build is recommended ... |
|
|
|
| Topic: Problems after PPPoE remote disconnection |
|
| Nuwanda Replies: 6 Views: 4792 |
Forum: Broadcom SoC based Hardware Posted: Fri Jun 12, 2009 23:42 Subject: Problems after PPPoE remote disconnection |
| Thank you very much! I'll try build 12188 as soon as I have a chance, and post back the results. Is 12188 a "recommended" build? |
|
|
|
| Topic: Problems after PPPoE remote disconnection |
|
| Nuwanda Replies: 6 Views: 4792 |
Forum: Broadcom SoC based Hardware Posted: Thu Jun 11, 2009 20:31 Subject: Problems after PPPoE remote disconnection |
| How is your router connected to your ISP Modem? Wireless or cable? Cable. |
|
|
|
| Topic: Problems after PPPoE remote disconnection |
|
| Nuwanda Replies: 6 Views: 4792 |
Forum: Broadcom SoC based Hardware Posted: Thu Jun 11, 2009 11:47 Subject: Problems after PPPoE remote disconnection |
| Does this happen only to me?? :? What should I do? Open a bug in the bug tracker? Does someone know if this was fixed in a newer revision? (I used revision 11296 because it was the recommended one in ... |
|
|
|
| Topic: Problems after PPPoE remote disconnection |
|
| Nuwanda Replies: 6 Views: 4792 |
Forum: Broadcom SoC based Hardware Posted: Wed Jun 10, 2009 4:17 Subject: Problems after PPPoE remote disconnection |
| Hi. I'm using DD-WRT v24-sp2 (01/01/09) micro-plus-ssh (SVN revision 11296M NEWD Eko) on a Linksys WRT54G2, which I use to connect to the internet using PPPoE. My ISP disconnects me every 12 hours a ... |
|
|
|
| Topic: pppoe doesn't always reconnect (on a WRT54G2) |
|
| Nuwanda Replies: 0 Views: 5780 |
Forum: Broadcom SoC based Hardware Posted: Sat May 16, 2009 22:12 Subject: pppoe doesn't always reconnect (on a WRT54G2) |
| Hi. Ever since I switched to DD-WRT, I've been having problems with pppoe reconnections. Sometimes, it didn't reconnect after hours since a disconnection, and I have to reconnect manually through the ... |
|
|
|
| Topic: Almost bricked a Linksys WRT54G2 |
|
| Nuwanda Replies: 6 Views: 3576 |
Forum: Broadcom SoC based Hardware Posted: Sat Apr 11, 2009 23:25 Subject: Almost bricked a Linksys WRT54G2 |
| You likely should take a look at the sticky about "if dd-wrt isn't working well." Oops. I didn't read that topic, as I didn't actually have a problem (except one that I described, which didn ... |
|
|
|
| All times are GMT |