I was wondering if you also tested using a different preformatted EXT2 USB flash drive? Does it give the same result?
I had similar issues with Clonezilla/MiniTool software not recognizing my external USB drive, and then I changed out the USB cable for a Belkin USB and it found it.
Router Model: TPLINK WR1043ND V2
Firmware Version: DD-WRT v3.0-r31277 std (02/07/17)
Kernel Version: Linux 3.18.47 #676 Tue Feb 7 03:07:52 CET 2017 mips
Status: OK
Reset: yes
Using QoS and usb/nas. Overall seems ok. Still some clients can disconnect when writing very large files (3-4GB) on the disks, but this occurs always with the same two clients, so I wonder if the problem can be with them.
HT40 degrades to HT20 when setting channel manually with lower extension channel, at least according with the sys-info page. No problem with upper extension channel. Funnily enough auto selects a lower extension channel.
For the monthly traffic graph: what suggested by Tatsuya46 above fixes it.
Didn't work for me. Disabled/Enabled and still nothing.
Router Model: TPLINK WR1043ND V2
Firmware Version: DD-WRT v3.0-r31277 std (02/07/17)
Kernel Version: Linux 3.18.47 #676 Tue Feb 7 03:07:52 CET 2017 mips
Status: OK
Reset: yes
Using QoS and usb/nas. Overall seems ok. Still some clients can disconnect when writing very large files (3-4GB) on the disks, but this occurs always with the same two clients, so I wonder if the problem can be with them.
HT40 degrades to HT20 when setting channel manually with lower extension channel, at least according with the sys-info page. No problem with upper extension channel. Funnily enough auto selects a lower extension channel.
For the monthly traffic graph: what suggested by Tatsuya46 above fixes it.
Didn't work for me. Disabled/Enabled and still nothing.
That is scary. Some other settings interfering? Did you apply settings both times (just to rule out the easy things ..).
Are you experiencing the some problem I have with HT40?
I was wondering if you also tested using a different preformatted EXT2 USB flash drive? Does it give the same result?
I had similar issues with Clonezilla/MiniTool software not recognizing my external USB drive, and then I changed out the USB cable for a Belkin USB and it found it.
thnx
Even tried Flashdrives
Nothing wrong with the drive, it works perfectly with all firmware up to and including build 29396, and not a single build after that _________________ TPLINK TL-WR2543ND (5GHz)
WRT160NL (2.4GHz)
Router#1 Model: Netgear WNDR3700 v1
Firmware Version: DD-WRT v3.0-r31277 std (02/07/17)
Kernel Version: Linux 3.10.105-rc1 #27714 Tue Feb 7 03:25:27 CET 2017 mips
Upgraded from r30949
Status: OK
Reset: No
Errors: None
Configuration:
- WLAN Access Point (2.4 and 5GHz) & Lan Switch (connected to cable provider's router)
- Isolated Guest (2.4 GHz) WLAN (DHCP server on separate bridge)
- USB NAS Server
Router#2 Model: Netgear WNDR3700 v2
Firmware Version: DD-WRT v3.0-r31277 std (02/07/17)
Kernel Version: Linux 3.10.105-rc1 #27716 Tue Feb 7 03:26:50 CET 2017 mips
Upgraded from r30949
Status: OK
Reset: No
Errors: Device did not reboot correctly after the upgrade,fixed with power off/on.
Configuration:
- WLAN Access Point (2.4 and 5GHz) & Lan Switch (connected to cable provider's router)
- Local DHCP Server (DNSMasq)
- Isolated Guest (2.4 GHz) WLAN (additional DHCP server on separate bridge)
- USB NAS Server
The ath1 issue seen with r31221 (no U-NII-2C band broadcast) is now fixed on both devices.
Router:TP Link WR940Nv3 (international version)
Firmware: 02-07-2017-r31277
Status: Still not work. It has no WAN connection and WAN LED behave wrongly. (same as the previous versions in 2016)
I was wondering if you also tested using a different preformatted EXT2 USB flash drive? Does it give the same result?
I had similar issues with Clonezilla/MiniTool software not recognizing my external USB drive, and then I changed out the USB cable for a Belkin USB and it found it.
thnx
Same for me. USB didnt work on 2/1/17 build either. The webGUI sees my sandisk cruzer mini 16gb and the partition and even says its mounted to /tmp/mnt/sda1 but its not. In my case the flash drive is formatted fat32. I havnt tried ext yet.
I was wondering if you also tested using a different preformatted EXT2 USB flash drive? Does it give the same result?
I had similar issues with Clonezilla/MiniTool software not recognizing my external USB drive, and then I changed out the USB cable for a Belkin USB and it found it.
thnx
Same for me. USB didnt work on 2/1/17 build either. The webGUI sees my sandisk cruzer mini 16gb and the partition and even says its mounted to /tmp/mnt/sda1 but its not. In my case the flash drive is formatted fat32. I havnt tried ext yet.
Just plain refuses to mount for me _________________ TPLINK TL-WR2543ND (5GHz)
WRT160NL (2.4GHz)
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Thu Feb 09, 2017 20:59 Post subject:
the usb mounting issue is not reproduceable for me. i use dd-wrt as nas storage on some routers without issues. maybe someone is able to help me here _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
