I've noticed my trendnet-812DRUv2 doesn't have ext2/3 modules installed either - kinda wish I understood the posts I read before I bought the router. Oh well, nice piece of ARM hardware, just lacking on the flash. I'm hoping I can compile for it, maybe get some time this weekend to start compiling DD-WRT.
The issue seems to be the same, only that K3 firmware knows about the error and cancels the process, but the K2.6 continues the process and producing the issue I linked.
Also even r30471 (this is the working one) shows "NVRAM 29KB / 256KB".
With K2.6 it was "NVRAM 29KB / 32KB".
I have been using dd-wrt.v24-3****_NEWD-2_K3 revisions on e3000 up to 2/28 2017 build 31544 (at time of writing this post), and consistently have issues with dhcp on unbridged wifi at 192.168.3.0/24 toggling itself randomly back to 192.168.1.0/24 for some reason and leases wrong IPs. It is very frustrating. I'm using custom vlans and multiple subnets though, dd-wrt for e3000 is the most reliable firmware to work with when it comes to vlans. Hoping 31544 stays stable for me.
consistently have issues with dhcp on unbridged wifi at 192.168.3.0/24 toggling itself randomly back to 192.168.1.0/24 for some reason and leases wrong IPs
I presume you've tested this after a reset (preferably `erase nvram`), and set things back up manually? If so, do k2.6 builds work properly? _________________ #NAT/SFE/CTF: limited speed w/ DD#Repeater issues#DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo#
OPNsense x64 5050e ITX|DD: DIR-810L, 2*EA6900@1GHz, R6300v1, RT-N66U@663, WNDR4000@533, E1500@353,
WRT54G{Lv1.1,Sv6}@250|FreshTomato: F7D8302@532|OpenWRT: F9K1119v1, RT-ACRH13, R6220, WNDR3700v4
I presume you've tested this after a reset (preferably `erase nvram`), and set things back up manually? If so, do k2.6 builds work properly?
Hello jwh7,
Pardon me for late reply, yes I did 'erase nvram' and 30/30/30 reset. I believe the problem is with my hardware, something is happening to my wifi transmitter in my e3000 router, even with stock setting and various older known-stable firmwares I was running into issue of wifi transmitter intermittently dropping (AP would toggle ON/OFF--which is what I think was responsible for causing my dhcp issues. Sometimes AP would completely disappear). To get wifi AP back no nvram erase or 30/30/30 would help, but rather unplugging router for couple hours does the trick.
I have been on r31825 mega and everything has been working perfectly in last 10 days
The 7/27 K3.X build flashed fine without issues because it is smaller
Post this in the appropriate test build thread. I doubt it will be seen either place though. _________________ I am far from a guru, I'm barely a novice.
Posted: Sun Oct 01, 2017 2:33 Post subject: xfs Unknown symbol exportfs_decode_fh
I am trying to mount a xfs formatted drive via USB and I get the error: Unknown symbol exportfs_decode_fh. Is it an issue with the module? Does anyone have one that works? I am using Brainslayer 33375 on a tew-818dru.
Posted: Sun Oct 01, 2017 9:44 Post subject: Re: xfs Unknown symbol exportfs_decode_fh
reubenbrown13 wrote:
I am trying to mount a xfs formatted drive via USB and I get the error: Unknown symbol exportfs_decode_fh. Is it an issue with the module? Does anyone have one that works? I am using Brainslayer 33375 on a tew-818dru.
Thanks
Not related with this thread. Open a new one. _________________ R6400v2 (boardID:30) - Kong 36480 running since 03/09/18 - (AP - DNSMasq - AdBlocking - QoS) R7800 - BS 31924 running since 05/26/17 - (AP - OpenVPN Client - DNSMasq - AdBlocking - QoS) R7000 - BS 30771 running since 12/16/16 - (AP - NAS - FTP - SMB - OpenVPN Server - Transmission - DDNS - DNSMasq - AdBlocking - QoS) R6250 - BS 29193 running since 03/20/16 - (AP - NAS - FTP - SMB - DNSMasq - AdBlocking)