Posted: Sun Mar 19, 2017 16:21 Post subject: R9000
Unable to connect any device if 2.4GHz Turbo Qam is turned on. Devices will see the 2.4GHz Turbo Qam network, but will continually ask for password when attempting to connect. States the password is incorrect.
Turn off Turbo Qam and 2.4GHz and everything works fine.
Router: Netgear R7800
Firmware: DD-WRT v3.0-r31690 (03/17/17)
Kernel: Linux 3.18.48 #131 SMP PREEMPT Fri Mar 17 01:22:47 CET 2017 armv7l
Status: Good
Reset: Yes (no choice otherwise no WAN connection to clients)
Errors: None
TP-Link Archer C7 V2.0 IL.
After one day working well the router stops to route anything. It had WAN IP, it's own IP, I got the web interface, but internet was not accessible. In the SYSLOG
I saw a few strange strings.
Jan 1 00:01:07 Archer-C7 daemon.err process_monitor[2719]: Last update failed, we need to re-update after 30 seconds
And many msgs like these:
Code:
Mar 19 23:55:20 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 WPA: pairwise key handshake completed (RSN)
Mar 20 00:12:37 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: disconnected due to excessive missing ACKs
Mar 20 00:12:38 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: authenticated
Mar 20 00:12:38 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: associated (aid 1)
Mar 20 00:12:38 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 RADIUS: starting accounting session D15B8193BDCE0F6E
Mar 20 00:12:38 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 WPA: pairwise key handshake completed (RSN)
Mar 20 00:13:02 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: disconnected due to excessive missing ACKs
Mar 20 00:13:03 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: authenticated
Mar 20 00:13:03 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: associated (aid 1)
Mar 20 00:13:03 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 RADIUS: starting accounting session 2879643A27FF5B4A
Mar 20 00:13:03 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 WPA: pairwise key handshake completed (RSN)
Mar 20 00:18:06 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: disconnected due to excessive missing ACKs
Mar 20 00:18:07 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: authenticated
Mar 20 00:18:07 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: associated (aid 1)
Mar 20 00:18:07 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 RADIUS: starting accounting session B7A5821CF33C6424
Mar 20 00:18:07 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 WPA: pairwise key handshake completed (RSN)
Mar 20 00:20:19 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: disconnected due to excessive missing ACKs
Mar 20 00:20:20 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: authenticated
Mar 20 00:20:20 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: associated (aid 1)
Mar 20 00:20:20 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 RADIUS: starting accounting session B7A5821CF33C6424
Mar 20 00:20:20 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 WPA: pairwise key handshake completed (RSN)
Mar 20 00:21:11 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: disconnected due to excessive missing ACKs
Mar 20 00:21:12 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: authenticated
Mar 20 00:21:12 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 IEEE 802.11: associated (aid 1)
Mar 20 00:21:12 Archer-C7 daemon.info hostapd: ath0: STA 44:6d:57:4f:60:77 RADIUS: starting accounting session 0056CE34C04DE650
Router: DIR-615 i1
Status: Good
Reset: Reset to defaults with flash procedure; erased NVRAM before and after flash
Errors: None
Router: TL-WDR3600 v. 1.5
Status: Good
Reset: Reset to defaults with flash procedure; erased NVRAM before and after flash
Notes: Appears to be more stable than r31571. The router had multiple random crashes/reboots on r31571. With this build, it's been up for almost 3 days without 1 crash/reboot. 5 GHz LED not illuminating, but radio is working.
DD-WRT v3.0-r31690 std (03/17/17)
Kernel: 3.18.48
Status: Fail
Reset: Yes
Errors: Unable to install, keep blinking power led all times, back to DD-WRT v3.0-r31571 std (03/04/17) working fine
DD-WRT v3.0-r31690 std (03/17/17)
Kernel: 3.18.48
Status: Fail
Reset: Yes
Errors: Unable to install, keep blinking power led all times, back to DD-WRT v3.0-r31571 std (03/04/17) working fine
The firmware.bin size is too large to install on 160NL after build r31645.
Not sure if / when this will be fixed....They might not fix it this time
Posted: Tue Mar 21, 2017 7:57 Post subject: Upgraded to r31690
Router: Buffalo WZR-HP-AG300H (WZR-600-DHP)
Firmware: DD-WRT v3.0-r31690 std (03/17/17)
Kernel: Linux 3.10.105 #29878 Fri Mar 17 02:01:14 CET 2017 mips
Status: Good
Reset: No
Errors: 5589, 5594
Resolved: 5653 - r30826 Limited to 20MHz channel width in 5GHz band
Router: D-Link DIR-615-E3/E4
Firmware: DD-WRT v3.0-r31690 std (03/17/17)
Kernel: Linux 3.10.105 #29878 Fri Mar 17 02:01:14 CET 2017 mips
Status: Good
Reset: No
Errors: None
DD-WRT v3.0-r31690 std (03/17/17)
Kernel: 3.18.48
Status: Fail
Reset: Yes
Errors: Unable to install, keep blinking power led all times, back to DD-WRT v3.0-r31571 std (03/04/17) working fine
The firmware.bin size is too large to install on 160NL after build r31645.
Not sure if / when this will be fixed....They might not fix it this time
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Tue Mar 21, 2017 10:35 Post subject:
Router Model TPLINK WR1043ND V2
Firmware Version DD-WRT v3.0-r31690 std (03/17/17)
Kernel Version Linux 3.18.48 #2279 Fri Mar 17 03:46:32 CET 2017 mips
reset: yes x2
status: operational
errors: none so far _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
DD-WRT v3.0-r31690 std (03/17/17)
Kernel: 3.18.48
Status: Fail
Reset: Yes
Errors: Unable to install, keep blinking power led all times, back to DD-WRT v3.0-r31571 std (03/04/17) working fine
The firmware.bin size is too large to install on 160NL after build r31645.
Not sure if / when this will be fixed....They might not fix it this time
Strange, it installed fine on my 160NL
Yes Sir, my bad -- the r31690 is ok for file size
r31690
7,996,416 bytes
Linksys WRT160NL
DD-WRT v3.0-r31690 std (03/17/17)
Linux 3.10.105 #29898 Fri Mar 17 02:51:15 CET 2017 mips
The r31671 & r31678 were too big both at -
8,000,512
I have run across some weirdness where 31690 will not install on some of my units --
If you run dmesg and look just under the MTD parts you'll see 'Oops: flash id'
See if yours is ->Oops: flash id 0x1c2017 .
and
maybe ndttung has ->Oops: flash id 0xc22017 .
I have two E2100L & two 160NL. All have ->Oops: flash id 0xc22017 .
None of these four routers will install build r31645 or later (GUI or TFTP - they just will not install).
And most builds of last few years always required TFTP to get the firmware on them.
Also have a third 160NL which has ->Oops: flash id 0x1c2017 .
It will install any build (provided file size is not too big)
I was looking into 'this' the other day but got bored messing with it.
Joined: 16 Dec 2016 Posts: 9 Location: Greensboring
Posted: Tue Mar 21, 2017 12:54 Post subject:
Does anyone know if the ACK time is auto when set to 0 on this build? I've tried various settings on a bridge at 50m and setting it to 0 is always slower than setting it to 350 (which seems ridiculously too far for my link but works).
DD-WRT v3.0-r31690 std (03/17/17)
Kernel: 3.18.48
Status: Fail
Reset: Yes
Errors: Unable to install, keep blinking power led all times, back to DD-WRT v3.0-r31571 std (03/04/17) working fine
The firmware.bin size is too large to install on 160NL after build r31645.
Not sure if / when this will be fixed....They might not fix it this time
Strange, it installed fine on my 160NL
Yes Sir, my bad -- the r31690 is ok for file size
r31690
7,996,416 bytes
Linksys WRT160NL
DD-WRT v3.0-r31690 std (03/17/17)
Linux 3.10.105 #29898 Fri Mar 17 02:51:15 CET 2017 mips
The r31671 & r31678 were too big both at -
8,000,512
I have run across some weirdness where 31690 will not install on some of my units --
If you run dmesg and look just under the MTD parts you'll see 'Oops: flash id'
See if yours is ->Oops: flash id 0x1c2017 .
and
maybe ndttung has ->Oops: flash id 0xc22017 .
I have two E2100L & two 160NL. All have ->Oops: flash id 0xc22017 .
None of these four routers will install build r31645 or later (GUI or TFTP - they just will not install).
And most builds of last few years always required TFTP to get the firmware on them.
Also have a third 160NL which has ->Oops: flash id 0x1c2017 .
It will install any build (provided file size is not too big)
I was looking into 'this' the other day but got bored messing with it.
dmesg
->Oops: flash id 0x1c2017
Not sure how to look for ndttung? _________________ TPLINK TL-WR2543ND (5GHz)
WRT160NL (2.4GHz)