Posted: Sun Sep 02, 2007 1:13 Post subject: wrt54g v.6 upgrade then downgrade then broke
ok, at first I had 0620 on my Linksys wrt54g v.6 router, then I had updated to 0806 and then to 0815
I had a bit of a stabability problem with 0815 so I tried to downgrade to 0620 since it worked best. I tried twice but they both failed, so I unpluged router and took it to my other room to work on it. I plug it in, now all I get is a blinking power light.I tried everything I could think of the fix it, any ideas?
lets go through what you did before it started screwing up.
you have a WRT54Gv6 (so 2mb only)
so you did the process to get from the linksys firmware -> linux install enabler firmware -> 06/20 MICRO
(v23 SP?, v24 ?)
then through dd-wrt web gui -> 08/15 MICRO (v23 sp? / v24?)
had stability problems - locking up / network connectivity issues (im guessing)
so you used the dd-wrt web gui -> 06/20 MICRO
it said failed twice
unplugged it and physically moved it to new location
wont boot (blinking green lights)
following questions:
did you reset defaults (admin/defaults) prior to attempting flash up/downgrade?
by hard reset you mean a 30 / 30 / 30 reset - right?
if no to first (1st) question and yes to second (2nd) question
then you probably bricked it
you could try the jumper short (probably wont work)
and probably need to get a jtag cable
best of luck _________________ 2x WRT54G v5, 2x WRT54G v2
1x WRT54G-TM
1x WRT54GL
1x WRT54G2 v1
2x BUFFALO WHR-G54S
2x BUFFALO WHR-G300N v2
1x BUFFLOW WHR-HP-G300N
1x La Fonera
FON Client Bridge tutorial
Joined: 09 Aug 2006 Posts: 1103 Location: Surabaya, Indonesia
Posted: Mon Sep 03, 2007 14:30 Post subject:
can you ping the router ? .. you can ping it...there's some hope that your router not bricked..
try to ping your router ... open the tftp then try to tftp the firmware again with pinging your router .. _________________ 365'pc WRT54GL 1.1 + DD-WRT wds - client mode - client bridge
337 GL+DD-WRT v23 SP1 Std
28 GL+DD-WRT v23 SP3 Std
13 WRT300N v.1 v24 06-20-07
2 GL/SP1/200 mW+Hyperlink 24 db >> 16 km Point to Point
Joined: 09 Aug 2006 Posts: 1103 Location: Surabaya, Indonesia
Posted: Mon Sep 03, 2007 15:13 Post subject:
thehackerdude wrote:
let me ask a dumb question, how do I ping it
if you had do hard reset for 30 second.. the default ip is 192.168.1.1 .. set your pc with the same subnet (e.g 192.168.1.2) . Open the windows command , in XP --> Start -> Run -> type "cmd" --> type in dos command "ping 192.168.1.1" then hit enter. So what the result ?
the router give reply or not ? _________________ 365'pc WRT54GL 1.1 + DD-WRT wds - client mode - client bridge
337 GL+DD-WRT v23 SP1 Std
28 GL+DD-WRT v23 SP3 Std
13 WRT300N v.1 v24 06-20-07
2 GL/SP1/200 mW+Hyperlink 24 db >> 16 km Point to Point
Joined: 09 Aug 2006 Posts: 1103 Location: Surabaya, Indonesia
Posted: Mon Sep 03, 2007 15:42 Post subject:
i see ... i think ... this is a JTAG time to revive your router .. the router is bricked _________________ 365'pc WRT54GL 1.1 + DD-WRT wds - client mode - client bridge
337 GL+DD-WRT v23 SP1 Std
28 GL+DD-WRT v23 SP3 Std
13 WRT300N v.1 v24 06-20-07
2 GL/SP1/200 mW+Hyperlink 24 db >> 16 km Point to Point