Posted: Wed Aug 09, 2017 2:08 Post subject: Need help resetting linksys AC1200V1 back to stock firmware
I uploaded dd-wrt firmware on a linksys AC1200 V1 to find out it does not have an option for VLAN. So I need to reset to stock firmware. Can someone kindly provide steps on how to do this? Thanks,
Posted: Thu Aug 10, 2017 21:47 Post subject: Marvell MVEBU based Hardware (WRT1200AC etc.)
Hi myersw,
I tried the links you provided including these instructions but no luck reverting back to linksys stock firmware.
****************
Booting back to stock from other patition
When you install DD-WRT over stock, it installs on a different partition. You can use the following command by entering it in DDWRT commands on the administration tab, Telnet or SSH to determine what partition DD-WRT is running on.
Code:
ubootenv get boot_part
The last number it returns is the partition (it will return 1 or 2). In my case, DD-WRT is on partition 1, so to return to Stock, enter (If yours returns 2, put 1):
Code:
ubootenv set boot_part 2
and then reboot. You can use the command
Code:
reboot
***************
Is there a .bin file from anywhere that I can use the flash DD-WRT. I tried flashing using the firmware from Linksys for AC1200 V1. No luck either. At least the stock firmware had VLAN options. That's the only reason I installed dd-wrt. without VLANS the router is useless.
Joined: 13 Jun 2006 Posts: 1608 Location: SE Michigan USA
Posted: Fri Aug 11, 2017 15:41 Post subject:
In the future when you post it would be helpful to whoever is going to try to answer your questions to know the verion of dd-wrt as well as the model and version of the router.
Sounds like you flashed more then once with dd-wrt so dd-wrt is on both partitions, at least that is how I read your post.
If you have dd-wrt r32670 or later installed then you should be able to flash the Linksys firmware through the dd-wrt UI. If not that late of a dd-wrt version, install the latest then you should be able to flash Linksys firmware. _________________ Unifi Security Gateway:Unifi Firmware Netgear r7800:Voxel Firmware Modem:Netgear CM500V voice and Data. ISP:Comcast tutorial for flashing "WRT" series: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813 DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117 Kong DD-WRT Config Tutorial: http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/ I tried to be normal once. Worst 2 minutes ever.
The firmware version of dd-wrt is:
DD-WRT v3.0-r28788 std (01/13/16)
The router is Linksys WRT1200AC Version 1
I think you're right: I did install the firmware twice the first flash then the upgrade. I guess running this command (ubootenv get boot_part ) which returned 2 would suggest that dd-wrt is installed on both partitions.
Where do I get dd-wrt r32670? And is there something special about it?
I am willing to try any firmware to go back to stock
I have tried just the stock firmware (Admin > Update Firmware) multiple times, the router reboots but it keeps going back to dd-wrt default settings.
Joined: 13 Jun 2006 Posts: 1608 Location: SE Michigan USA
Posted: Sun Aug 13, 2017 3:35 Post subject:
You have overwritten the Linksys firmware. Easiest way to reinstall Linksys firmware if you want to is to install latest dd-wrt for your router. After you have the latest version of dd-wrt installed you can then flash the Linksys firmware through the dd-wrt UI same as updating dd-wrt. Version you are running is quite old, by the way.
Go here for lastest versions of the dd-wrt firmware.
Posted: Sun Aug 13, 2017 8:59 Post subject: Re: Need help resetting linksys AC1200V1 back to stock firm
sisidalim wrote:
I uploaded dd-wrt firmware on a linksys AC1200 V1 to find out it does not have an option for VLAN. So I need to reset to stock firmware. Can someone kindly provide steps on how to do this? Thanks,