[maguvu]

[mac913]

I have one R7000 loaded with 33010M Release 2017-09-16 and the "ip" command works.

I have loaded the same build to another R7000 and the "ip" command doesn't work and my custom scripts are failing. I have enlarged the "ip" shown in folder /usr/sbin but says not found?? I have tried Factory Reset & erase nvram and still the same problem.



DD-WRT v3.0-r33010M kongac (c) 2017 NewMedia-NET GmbH
Release: 09/15/17

DD-WRT login: root
Password:
==========================================================

___ ___ _ _____ ______ ____ ___
/ _ \/ _ \___| | /| / / _ \/_ __/ _ __|_ / / _ \
/ // / // /___/ |/ |/ / , _/ / / | |/ //_ <_/ // /
/____/____/ |__/|__/_/|_| /_/ |___/____(_)___/

DD-WRT v3.0
http://www.dd-wrt.com

==========================================================


BusyBox v1.27.1 (2017-09-15 16:37:48 CEST) built-in shell (ash)

root@DD-WRT:~# ip
-sh: ip: not found

root@DD-WRT:~# ip
-sh: ip: not found

root@DD-WRT:~# ls /usr/sbin
aiccu ifenslave ntfs-3g smbd
arping igmprt ntpclient smbpasswd
astcanary igs nvram snmpd
asterisk inadyn olsrd speedtest_cli
astgenkey ip openser splashd
bcrelay ip6tables openser_gen_ha1 svqos
bgpd ip6tables-restore openserctl svqos2
bpalogin ip6tables-save openssl swanctl
brctl ipheth-loop openvpn tc
chat ipheth-pair ospfd tcpdump
chilli ipsec p910nd telnetd
chilli_multicall iptables pimd temps
chilli_opt iptables-restore pound topcpu
chilli_query iptables-save poundctl udhcpd
chilli_radconfig iwconfig pppd upnp
chilli_response iwgetid pppoe-multi uqmi
chroot iwlist pppoe-relay usb_modeswitch
clients iwpriv pppoe-server usbip
comgt iwspy pptp usbipd
cron lighttpd pptpctrl usbmuxd
dbtextctl lld2d pptpd uuidd
dhcp_lease_time macupd privoxy vpnc
dhcp_release mf_sip_tracer.sh proftpd vpnc-disconnect
dhcpfwd milkfish_services radius-client watchquagga
disktype minidlna radiusallow wclients
dnscrypt-proxy mkfs.jffs2 radiusd wdctl
dnsmasq mklost+found radiusdisallow wifidog
dropbear monit radvd wiviz
dropbearconvert mtd_debug radvdump wl
dropbearkey mtr rasterisk wlconf
dropbearmulti nanddump readprofile wol
dumpleases nandwrite repeater wpa_supplicant
e2freefrag nas rflow wrt-radauth
ebtables nas4not ripd xl2tpd
emf nas4wds ripngd zabbix_agentd
filefrag nmbd samba_multicall zebra
flash_erase notifier sendmail
flash_eraseall nstxcd shatc
httpd nstxd shatd

root@DD-WRT:~# /usr/sbin/ip
-sh: /usr/sbin/ip: not found

UPDATE...

The only other way I was able to get the IP command working was to run bootstrap and install the ip-full package.

2nd UPDATE...

Kong's Release 2017-09-19 of Build 33010M resolved the issue. Thanks for the quick Upadte!!

[e3000usr]

Thank you kong and brainslayer

Router: Asus RT-AC56U
Firmware: DD-WRT v3.0-r33010M kongac (09/15/17)
Previous: DD-WRT v3.0-r33010M kongac (08/09/17)
Kernel: Linux 4.4.87 #439 SMP Fri Sep 15 16:41:44 CEST 2017 armv7l
Status: OK
Reset: NO
Errors: NONE

[James Greystone]

Odd when I upgrade to this release my VPN says connected but when I check it is actually my non vpn IP showing on the internet.

Installed previous build and all is working again.

[labo]

There is another update on the same build from Kong today.
When I used dup it said no new firmware, means the version is the same but the bug fix that Kong mentioned probably in place.
You can force update, if you login to your router:
for example: R7000

ddup --flash-remote http://www.desipro.de/ddwrt/K3-AC-Arm/TEST/dd-wrt.v24-K3_AC_ARM_STD.bin

Firmware: DD-WRT v3.0-r33010M kongac (09/19/17

[mac913]

Router: 2x R7000
Firmware: 33010M (R.2017.08.09)(over 35days uptime) -> 33010M (R.2017.09.15)
Kernel: Linux 4.4.80 #422 SMP -> Linux 4.4.87 #439 SMP
Status: Both Working & Monitoring
Reset: Yes
Errors: None so far
UpTime: over an hour

#1 R7000 (WAN + HE-IPv6 + OpenVPN Client#1)
- Disabled SFE
- IPv4 + HE IPv6 via 6in4 Static Tunnel
- USB Custom Startup Script for Route Tables, OpenVPN Client & Cron Scripts
- GUI Firewall & Startup Scripts
- WiFi Disabled
- SPI with non-filtered Multicast
- WAN port -> Cable Modem
- DNSCrpyt for IPv4 & IPv6
- NTP with Blank IP
- Cron Job - Monitor WAN & OpenVPN Connections
- DDNS Custom with DNSoMatic
- 7 BRs, 9 VLANS & 7 Assignments
- SSH (WAN Access), Telnet & Syslog
- WAN Traffic Disabled
- USB Storage with Auto Mount for Scripts Only
- ebtables + ip6tables used
- YAMon 3.3.2

#2 R7000 (WiFi + OpenVPN Client#2)
- Disabled SFE
- IPv4 Only
- USB Custom Startup Script for OpenVPN Client
- GUI Firewall Script
- 2.4Ghz Radio with 3 SSIDs (BW 40Mhz)
- 5Ghz Radio with 2 SSIDs (BW 80Mhz)
- SPI with non-filtered Multicast
- WAN Port (static IP) Assignment to vlan8 -> Vlan Switch
- DNSCrpyt x4 for IPv4
- NTP with Blank IP
- Cron Job - Monitor OpenVPN Connection
- 5 BRs, 7 VLANS & 12 Assignments
- SSH (local only), Telnet & Syslog
- WAN Traffic Disabled
- ebtables used
- USB Storage with Auto Mount for Scripts & Bootstrap
- Installed Bootstrap to install ip-full package (ip command wasn't working with this build on this router see earlier post above)

UPDATE...

Kong NEW Release 2017-09-19 of Build 33010M

Updated both R7000s via ddup --flash-remote http://www.desipro.de/ddwrt/K3-AC-Arm/TEST/dd-wrt.v24-K3_AC_ARM_STD.bin command that CloneVince used. Now using Kernel Version Linux 4.4.88 #441 SMP Tue Sep 19 22:44:21 CEST 2017 armv7l. Now the "ip" command works without the need of the bootstrap package.

Thanks KONG!!


Router: 2x R7000
Firmware: 33010M (R.2017.09.19)
Kernel: Linux 4.4.88 #441 SMP Tue Sep 19 22:44:21 CEST 2017 armv7l
Status: Both Working & Monitoring
Reset: No, Firmware installed via ddup command
Errors: None so far
UpTime: minutes

[e3000usr]

[-XPTO-]

Astrill VPN applet working again with the 09/19 release.

Thank you, Kong.

[James Greystone]

[mac913]

[staplefood]

New here to posting here...

Has the QoS been touched in anyway? I am getting high amounts of bufferbloat now. More than without QoS enabled.

Using an R7000 with a 100/10 connection. I've set me QoS to 75/10 now to reduce bufferbloat, but it use to be 95/10.

Using HTB with FQ_CODEL

[wabe]

[staplefood]