Almost made it 8 hours. This one rebooted on me on my 3200. 33345 did the same. Back to 33342 for me.
Do you have SFE enabled? If so disable SFE and see if that fixes your reboot issues. Does for other folks.
SFE was disabled. Ath2 wasn't disabled. Disabled ath 2 and tried again. Max uptime has been 15 hours before reboot. IPV6 may be the cause, not sure yet though. _________________ NETGEAR R9000 DD-WRT v3.0-r45192 std (12/29/20) (ROUTER)
NETGEAR ORBI Stock FW V2.7.2.102 (MESH)
WRT3200ACM (BS Build Usually) (BACKUP)
Almost made it 8 hours. This one rebooted on me on my 3200. 33345 did the same. Back to 33342 for me.
Do you have SFE enabled? If so disable SFE and see if that fixes your reboot issues. Does for other folks.
SFE was disabled. Ath2 wasn't disabled. Disabled ath 2 and tried again. Max uptime has been 15 hours before reboot. IPV6 may be the cause, not sure yet though.
Reboots have been an issue on my 3200acm as well, starting r33215.
Posted: Fri Sep 22, 2017 7:22 Post subject: Router WLAN -> AP WLAN Throughput 2-4 MB/s ???
WRT1900AC v2 as router + WRT1900ACS v1 operating as 'dumb' access point.
▬▬ Router WLAN PC -> AP WLAN PC … 2GB file transfer = 2-4 MB/s YUCK ▬▬
Any idea as to why the Router WLAN -> AP WLAN of this WRT1900 combo would be 1/10th of all of its other functions???
In every scenario each WRT1900 5GHz WLAN is 80MHz on separated channels 36, 161 and function in VHT-MCS 8-9.
▬▬ Configurations Tested ▬▬
• ACv2 as router & ACSv1 as AP
• ACSv1 as router & ACv2 as AP
• Out of box OEM FW on both
• Updated OEM FW on both
• ACv2 as router w/ OEM FW & LEDE on the ACSv1 as AP ( https://davidc502sis.dynamic-dns.net/ Kernel version 4.9.44 WiFi driver 10.3.4.0-20170810
• LEDE on both
▬▬ Observed Throughputs ▬▬
WLAN to WAN on either router or AP via speedtest.net = 240mbps ~ 30MB/s
Router LAN to AP LAN = 100+ MB/s
Router LAN to Router attached storage = 90+ MB/s
Router WLAN to Router attached storage = 40MB/s
Router WLAN to Router WLAN = 14-15 MB/s
AP WLAN to AP WLAN = 14-15 MB/s
Stats -> Graphs -> CPU hasn't exceeded 6% for either WRT unit
I've tried numerous client PCs and Macs w/ Intel AC and Broadcom AC adapters.
Color me stumped.
I'm excited to try a Brainslayer build when @myersw indicates it gets the more recent wireless driver and he recommends it as stable.
I've run r33375 on my Linksys WRT1900ACS V2 successfully for a few days. My set up is fairly straightforward. I use IVPN for an OpenVPN client. No reboots so far, and the performance as measured by iperf3 varies from 350 Mbits/s to 670 Mbits/s depending on where I'm at in my house. _________________ FIRMWARE: 6-20-2018 - r36168
MODEM: ARRIS SURFBoard SB6183
ROUTER: Linksys WRT1900ACS V2
ISP: TWC Spectrum 100 Mbps Download | 10 Mbps Upload
SERVICES: IVPN OpenVPN Client
so, i too bit the bullet and have been running r33375 for close to 48 hrs now. perhaps it's me but i have a few comments.
happened to notice a real-time clock in the upper right of the interface. it's kind of cool.
is there any additional doc on mtu auto setting? i use auto and i see 1500 grayed out. does that mean it's set to 1500? yes, i know i can set it manually but i'm a bit curious to know if the 1500 is significant.
sfe is enabled. i notice no performance change if i disable it. i've read about it and it appears to be a perf boost when it's working. how can we tell?
if i stepped on any toes here, i'm happy to start a new thread/topic. _________________ asus rt-ac86u stock: 3.0.0.4.384_45149
wrt3200acm: r34578 {sunset}
"why nibble when u can take a byte."
I've been running r33375 on my Linksys WRT1900ACS V2 as noted in my post above. For what it's worth, the CPU seems to run cooler now. It's at 68 C to 70 C whereas formerly I am used to seeing 75 C to 78 C.
This observation is far from scientific, however I thought I'd mention it. _________________ FIRMWARE: 6-20-2018 - r36168
MODEM: ARRIS SURFBoard SB6183
ROUTER: Linksys WRT1900ACS V2
ISP: TWC Spectrum 100 Mbps Download | 10 Mbps Upload
SERVICES: IVPN OpenVPN Client
i'm reverting back.. this build appears to have an intermittent GUI functionality... sometimes i am able to access it sometimes not and when i am able to there seems to be a delay in the tabs..
i'm reverting back.. this build appears to have an intermittent GUI functionality... sometimes i am able to access it sometimes not and when i am able to there seems to be a delay in the tabs..
Have you tried private tab? I have had this since forever with any 16' 17' build but priv tab works it out. _________________ R6400v2 (boardID:30) - Kong 36480 running since 03/09/18 - (AP - DNSMasq - AdBlocking - QoS) R7800 - BS 31924 running since 05/26/17 - (AP - OpenVPN Client - DNSMasq - AdBlocking - QoS) R7000 - BS 30771 running since 12/16/16 - (AP - NAS - FTP - SMB - OpenVPN Server - Transmission - DDNS - DNSMasq - AdBlocking - QoS) R6250 - BS 29193 running since 03/20/16 - (AP - NAS - FTP - SMB - DNSMasq - AdBlocking)
i'm reverting back.. this build appears to have an intermittent GUI functionality... sometimes i am able to access it sometimes not and when i am able to there seems to be a delay in the tabs..
Have you tried private tab? I have had this since forever with any 16' 17' build but priv tab works it out.
no i haven't. i'm using a windows pc and whatever browser (firefox/chrome) i tried there is delay in gui for this build however when i use an ipad on any browser (safari/chrome) it loads up just fine.
with the previous build, r33345 the gui loaded fast with the pc..
Running for nearly 4 days with no reboots.
VPN Client (IP Vanish) running with PBR (Policy Based Routing) and PBR kill switch. All working perfectly with more than acceptable VPN speeds (Comparable to windows client speeds).
GUI is fast and problem free.
Problems:
1. Internet LED does not go out if cable removed.
2. SFE (Shortcut Forwarding Engine) disabled as caused browsing problems when using PBR (but only for clients setup in PBR).
3. LAN WIFI file transfers are slow (<5MBs).
