Excellent Performance on my WRT3200ACM with this build. _________________ My "WRT" rant, and why I have gone ddwrt on x86, no more consumer routers. ( ac86u as access points & bridges )
lots or reboots with 33413 - at least 1 every 12 hrs after about a week of no issues. while reading that it happens, it was a first for me. btw, i've always had sfe enabled. the only change from other builds was configuring a static ip for wol purposes. probably unrelated but i'm not really doing any special - 1 static and a nas device.
many thanks for the "timeline" url. ain't much but it beats zilch. at halftime, i'll go and load this latest build.
update: r33492 is about 45% slower that r33413 in both bands. lan is fine. it's like performance is back to previous releases. oh, well. _________________ asus rt-ac86u stock: 3.0.0.4.384_45149
wrt3200acm: r34578 {sunset}
"why nibble when u can take a byte."
if you upgrade to a newer build does it overwrite the daily/monthly bandwidth found in the status tab of the previous build? _________________ Router: Linksys WRT1200AC v2
Firmware: DD-WRT v3.0-r44048 std [08/02/20]
Bandwidth/Traffic Question:
I checked and I do see stats for previous months [update: actually I seem to have 1yrs worth of data - looked back to 10/2016] (ref: status-WAN-traffic). I always just webflash/upgrade and don't reset or change config (I've upgraded pretty much to every build).
Build Install Stat:
Installed r33492 on my WRT1900ACSv1 as a flash upgrade, keeping existing config. Uptime 2 days, 17hrs so far. Will post if I have any issues.
________________
Linksys WRT1900ACS v1 - r33492
Joined: 13 Jun 2006 Posts: 1608 Location: SE Michigan USA
Posted: Fri Oct 13, 2017 16:27 Post subject:
You can also back up the traffic info and restore after a new install. I have done this when doing upgrades via the Linksys UI, which puts a clean copy of the dd-wrt firmware in my case. Others have said they still had the config, I never have doing it through the Linksys UI, but as I said you can backup the traffic just to be safe before the upgrade. _________________ Unifi Security Gateway:Unifi Firmware Netgear r7800:Voxel Firmware Modem:Netgear CM500V voice and Data. ISP:Comcast tutorial for flashing "WRT" series: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813 DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117 Kong DD-WRT Config Tutorial: http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/ I tried to be normal once. Worst 2 minutes ever.
Joined: 05 Apr 2017 Posts: 981 Location: Louisiana, USA
Posted: Fri Oct 13, 2017 16:38 Post subject:
Gotta keep them Internet Service Providers honest! Especially now that most are implementing data caps as a way of punishing people who have 'cut the cord'. _________________ DD-WRT Installation & Setup TUTORIAL http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117
FIRMWARE:OpenWrt SNAPSHOT r8217-2cc821e / LuCI Master (git-18.276.41146-280dd33) MODEM:ARRIS SURFBoard SB8200 ROUTER:Linksys WRT32X USB NAS:Western Digital BLACK 1 TB Hardrive + Startech USB 3.0 External SATA III Enclosure
So far this version has been the best performing of any versions I've used on my WRT1900ACSV2...Everything very quick and stable. Speeds are as good or better than stock firmware.
Running this for just about 48 hours and WiFi has dropped out completely twice and required a router reboot. Dropped as in cannot reconnect and cannot see SSID.
Every wifi device here, printers, tablets, phones and computers all dropped.
Joined: 13 Jun 2006 Posts: 1608 Location: SE Michigan USA
Posted: Fri Oct 13, 2017 22:09 Post subject:
GDTech wrote:
WRT3200ACM
Running this for just about 48 hours and WiFi has dropped out completely twice and required a router reboot. Dropped as in cannot reconnect and cannot see SSID.
Every wifi device here, printers, tablets, phones and computers all dropped.
Wow! I was running this build for 2 days with lots of streaming by teen as well as me in the eve. Did not experience any dropouts. Especially having to reboot router.
There is one dhcp issue not sometimes comes up that maybe you have. Sometimes you will not get a IP address renewal. Did you by any chance check for IP address renewal? If windows doing from the command prompt
ipaddress /release
ipaddress /renew
ipaddress /all (shows everything about the lease.) The simple fix is to change the dhcp lease time from 1440 to anything else and save then change back to 1440. That has worked for me. _________________ Unifi Security Gateway:Unifi Firmware Netgear r7800:Voxel Firmware Modem:Netgear CM500V voice and Data. ISP:Comcast tutorial for flashing "WRT" series: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813 DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117 Kong DD-WRT Config Tutorial: http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/ I tried to be normal once. Worst 2 minutes ever.
2 days, 5 hrs. no issues. still screaming fast. _________________ My "WRT" rant, and why I have gone ddwrt on x86, no more consumer routers. ( ac86u as access points & bridges )
Bandwidth/Traffic Question:
I checked and I do see stats for previous months [update: actually I seem to have 1yrs worth of data - looked back to 10/2016] (ref: status-WAN-traffic). I always just webflash/upgrade and don't reset or change config (I've upgraded pretty much to every build).
thanks for the assurance.. i will proceed with the update then..
myersw wrote:
You can also back up the traffic info and restore after a new install. I have done this when doing upgrades via the Linksys UI, which puts a clean copy of the dd-wrt firmware in my case. Others have said they still had the config, I never have doing it through the Linksys UI, but as I said you can backup the traffic just to be safe before the upgrade.
ok, i will try the backup and restore method first, i'm more inclined with the upgrade by booting through the alternate/linksys stock gui and upgrade from there.. i don't want to do the webflash since i still want to keep the existing stock linksys partition in case i mess up i still have the stock fw to get back just to be safe..
thanks all for the inputs.. really appreciate it.. _________________ Router: Linksys WRT1200AC v2
Firmware: DD-WRT v3.0-r44048 std [08/02/20]
I have a lot of confidence that this is the build that will finally be stable. I have made some adjustments over the last few days on my router setup and just am approaching 24 hours of stability. On my bridge setup, it's been going for a day and a half. Very happy so far, and hope it continues. Thanks @BrainSlayer! I will keep folks posted. _________________ WRT3200ACM x2 presently running LEDE.
r33492 is working very well for my Linksys WRT1900ACS V2. I have a fairly simple setup with an OpenVPN client, streaming TVs and music throughout my home. Measured with iperf3, I see wireless speeds between 350 Mbit/s and 700 Mbit/s depending on where I'm at with relation to the router. No reboots since I installed it 3 days ago.
Working mostly fine for me too on WRT3200ACM, with 2 exceptions:
1) If I remove my WAN cable, the light stays white and the DD-WRT UI still shows the same IP, as it if is still connected.
2) Using Astrill OpenVPN applet, when assigning tunnels to specific LAN IPs, they don't get any internet connection at all. I know this may be an issue with the applet itself, but could be some compatibility issue caused by the firmware.
I have not tested previous firmwares, but I know this applet is tested to work perfectly on some old firmwares and devices (as Astrill support claim. They didn't test it on this device with any firmware). Unfortunately old firmwares don't play nicely with my router, so can't test.
it's like performance is back to previous releases. oh, well.