WRT610N BRICKED

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3, 4, 5, 6, 7
View previous topic :: View next topic  
Author Message
Peabody
DD-WRT Guru


Joined: 28 Dec 2009
Posts: 1518
PostPosted: Thu Jun 10, 2010 8:22    Post subject: Reply with quote
ahbecan wrote:
Anybody?


read the serial debricking post in the peacock announcement #6.
_________________
I fix "shortcuts". If you don't have time to read thoroughly, I don't have time to re-type what you missed.
Back to top View user's profile Send private message
Sponsor
redhawk0
DD-WRT Guru


Joined: 04 Jan 2007
Posts: 11564
Location: Wherever the wind blows- North America
PostPosted: Thu Jun 10, 2010 12:07    Post subject: Reply with quote
ahbecan wrote:
Anybody?


Cntl-C in the Serial window right when you power it on....until you get a "CFE>" prompt

issue

nvram erase

get your tftp program ready with a mini_610n.bin.

Now issue

go at the CFE> prompt and start the tftp program.....if it doesn't start flashing....your timing isn't right...try again.

once it flashes...you should be good to go.

No MIRCO builds on this unit.

redhawk
_________________
The only stupid question....is the unasked one.
Back to top View user's profile Send private message
ahbecan
DD-WRT Novice


Joined: 29 Jul 2009
Posts: 14
PostPosted: Thu Jun 10, 2010 21:57    Post subject: Reply with quote
Peabody wrote:
ahbecan wrote:
Anybody?


read the serial debricking post in the peacock announcement #6.

thanks
_________________
WRT610N v1 (14929_mega)
Back to top View user's profile Send private message
ahbecan
DD-WRT Novice


Joined: 29 Jul 2009
Posts: 14
PostPosted: Thu Jun 10, 2010 21:59    Post subject: Reply with quote
redhawk0 wrote:
ahbecan wrote:
Anybody?


Cntl-C in the Serial window right when you power it on....until you get a "CFE>" prompt

issue

nvram erase

get your tftp program ready with a mini_610n.bin.

Now issue

go at the CFE> prompt and start the tftp program.....if it doesn't start flashing....your timing isn't right...try again.

once it flashes...you should be good to go.

No MIRCO builds on this unit.

redhawk

Thank you, I will try.
_________________
WRT610N v1 (14929_mega)
Back to top View user's profile Send private message
ahbecan
DD-WRT Novice


Joined: 29 Jul 2009
Posts: 14
PostPosted: Mon Jun 14, 2010 22:48    Post subject: Reply with quote
Yes, OK. Smile It works. Thanks to everyone.
_________________
WRT610N v1 (14929_mega)
Back to top View user's profile Send private message
Puppetnation
DD-WRT Novice


Joined: 13 Aug 2010
Posts: 38
Location: Italy
PostPosted: Mon Aug 16, 2010 11:36    Post subject: Reply with quote
Hi there,
why 3.3V is not required?
I'll use a RS232 to TTL interface (still has to come) which needs to be powered in some way...

With a tester I can see 3.3V pin on the router board HAS 3.3V power so I can get it from there, right?
Back to top View user's profile Send private message
cucu0010
DD-WRT Novice


Joined: 29 May 2009
Posts: 14
PostPosted: Sat Mar 05, 2011 21:41    Post subject: Reply with quote
I just purchased a audio to USB cable and plug the cable according to this post https://forum.openwrt.org/viewtopic.php?id=16733&p=2, unfortunately, I am unable to see anything using Hyper Terminal. My router is wrt610n v2. I tried just about everything and currently running out of clues. Does anyone have a clue to what is happening....why I am not getting anything when the terminal is plug and the router is turn on. Please assist with this. The router at this point has the power light just flashing because I convert it to an E3000 and then downloaded the wrong firmware. Ever since the power light just flash on and off repeatedly. Thank you for any assistance.
Back to top View user's profile Send private message
catohagen
DD-WRT Novice


Joined: 07 Jan 2007
Posts: 27
PostPosted: Sun Jan 24, 2016 13:01    Post subject: revived wrt610n v1 Reply with quote
Hi, just to report, i've revived my bricked WRT610n v1 thanks to Hans_it post here :
http://www.dd-wrt.com/phpBB2/viewtopic.php?p=255594&sid=2b1b314b475906eb23385136c95b34e6#255594

I soldered small pieces of cable onto the serialport pads, connected to usb-to-serial (CP2102 USB 2.0 to UART TTL 6PIN Module Serial Converter from ebay)
Didnt get anything over serial port, but after a while I disconnected 3.3v and shit started to flow over serial output as soon as router was plugged in.

Followed Hans_it instuctions except I had to break the boot procedure with ctrl-c instead of Enter

Orginal linksys WRT610N v1 firmware flashed back with tftp (router is 192.168.1.1 and computer is 192.168.1.20):
http://www.dd-wrt.com/phpBB2/viewtopic.php?p=650793#650793

Then I flashed this dd-wrt image from orginal linksys firmware :
http://download1.dd-wrt.com/dd-wrtv2/downloads/others/eko/BrainSlayer-V24-preSP2/2010/08-12-10-r14929/broadcom/dd-wrt.v24_mega_wrt610n.bin

final image flashed was a kong build :
http://www.desipro.de/ddwrt-ren/K26/r18730/usb-ftp-samba3-vpn-nv32k-broadcom.bin

thanks everyone
_________________
test...
Back to top View user's profile Send private message
tedm
DD-WRT Guru


Joined: 13 Mar 2009
Posts: 555
PostPosted: Sun Oct 22, 2017 7:48    Post subject: use the kong build Reply with quote
I just tried the Brainslayer build 33555 in an effort to patch for the KRACK vulnerability and wl1 is still broken. That build is
https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2017/10-20-2017-r33555/broadcom/dd-wrt.v24_mega_generic.bin
Back to top View user's profile Send private message
Goto page Previous  1, 2, 3, 4, 5, 6, 7 Display posts from previous:    Page 7 of 7
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum