Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29440_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ R7000 Nighthawk - DD-WRT v3.0-r50308
R7000 Nighthawk - DD-WRT v3.0-r50308
~~~~~~~~~~Dismantled for learning opportunities~~~~~~~~~~
WRT54Gv2
WRT54Gv8.2
~~~~~~~~~~Other Settings~~~~~~~~~
https://nextdns.io/?from=2d3sq39x https://pi-hole.net/ https://github.com/DNSCrypt/dnscrypt-proxy
Router: R7000 (Gateway & WiFi Disabled)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/18)
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: Problem with OpenVPN
Reset: no (from build 36400M)
Errors: OpenVPN Client Crashing
My OpenVPN script from Build 35550M was working fine. Today I was testing Kong's Build 36400M and now 36410M and OpenVPN Client is crashing with the following error in the syslog...
Jul 28 19:15:28 dot01-MAIN daemon.err openvpn[1769]: ERROR: Cannot open TUN/TAP dev /dev/net/tun: No such file or directory (errno=2)
UPDATE...
Okay took a break and started looking for a solution and DragonC posted a solution at the bottom. Now I have the new build working. Thanks DragonC for posting a fix!
Router: R7000 (Gateway & WiFi Disabled)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/18)
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: Working
Reset: no (from build 36400M)
Errors: None
Thanks B.S. & Kong for your Work! _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
My OpenVPN script from Build 35550M was working fine. Today I was testing Kong's Build 36400M and now 36410M and OpenVPN Client is crashing with the following error in the syslog...
Try to enable OpenVPN server in the Services tab and maybe put some delay into your scripts before it starts executing. BS has been changing the codes that’s controlling the router behaviors and I guess that’s messing up your scripts.
Or as you found out, loading the tun module works as well.
Last edited by quarkysg on Sun Jul 29, 2018 6:00; edited 1 time in total
Router: Netgear R7000
Firmware: DD-WRT v3.0-r36410M kongac (07/28/2018)
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: Working
Reset: No
Previous: 36400M
Errors: No
CPU Temperature : 56.4 °C / WL0 48.5 °C / WL1 51.0 °C
Working very well :
Router mode : DHCP
SFE Enable STP Enable
DNSMasq
Encrypt DNS
Cache DNSSEC data
Validate DNS Replies (DNSSEC)
Local DNS
No DNS Rebind
Query DNS in Strict Order
Usb
Nas, Samba, JFFS2,
wl0, wl1
Vpn (OpenVPN Client) No problem
Router: Netgear R8000
Firmware: DD-WRT v3.0-r36410M kongac (07/28/18 )
Kernel: 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: Ok
Reset: No
Errors: None
Updated with ddup --flash-latest keeping all settings. No errors at all.
Also, I can confirm that the slow https bug has finally been corrected! _________________ Linksys WRT1900ACS V2 dd-wrt bs r35034
Netgear R8000 dd-wrt kongac r36440M
Router: R7000 (Gateway & WiFi Disabled)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/18)
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: Problem with OpenVPN
Reset: no (from build 36400M)
Errors: OpenVPN Client Crashing
My OpenVPN script from Build 35550M was working fine. Today I was testing Kong's Build 36400M and now 36410M and OpenVPN Client is crashing with the following error in the syslog...
Jul 28 19:15:28 dot01-MAIN daemon.err openvpn[1769]: ERROR: Cannot open TUN/TAP dev /dev/net/tun: No such file or directory (errno=2)
UPDATE...
Okay took a break and started looking for a solution and DragonC posted a solution at the bottom. Now I have the new build working. Thanks DragonC for posting a fix!
Router: R7000 (Gateway & WiFi Disabled)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/18)
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: Working
Reset: no (from build 36400M)
Errors: None
Thanks B.S. & Kong for your Work!
Router: R7000 (WiFi Router)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/18)
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: No Working
Reset: YES (erase nvram then factory defaults)
Errors: Wifi Issues back to Build 35550M
A working WiFi setup from Build 35550M now drops clients with Build 36410M back to Build 35550M.
My WiFi setup on WL0 with 2 VAPs & WL1 with 1 VAPs a total of 5 SSIDs. _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Router: R7000 (Gateway & WiFi Disabled)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/1
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: Problem with OpenVPN
Reset: no (from build 36400M)
Errors: OpenVPN Client Crashing
My OpenVPN script from Build 35550M was working fine. Today I was testing Kong's Build 36400M and now 36410M and OpenVPN Client is crashing with the following error in the syslog...
Jul 28 19:15:28 dot01-MAIN daemon.err openvpn[1769]: ERROR: Cannot open TUN/TAP dev /dev/net/tun: No such file or directory (errno=2)
UPDATE...
Okay took a break and started looking for a solution and DragonC posted a solution at the bottom. Now I have the new build working. Thanks DragonC for posting a fix!
Router: R7000 (Gateway & WiFi Disabled)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/1
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: Working
Reset: no (from build 36400M)
Errors: None
Thanks B.S. & Kong for your Work!
Router: R7000 (WiFi Router)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/1
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: No Working
Reset: YES (erase nvram then factory defaults)
Errors: Wifi Issues back to Build 35550M
A working WiFi setup from Build 35550M now drops clients with Build 36410M back to Build 35550M.
My WiFi setup on WL0 with 2 VAPs & WL1 with 1 VAPs a total of 5 SSIDs.
Router: R7000 (Gateway & WiFi Disabled)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/18)
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: Problem with OpenVPN
Reset: no (from build 36400M)
Errors: OpenVPN Client Crashing
My OpenVPN script from Build 35550M was working fine. Today I was testing Kong's Build 36400M and now 36410M and OpenVPN Client is crashing with the following error in the syslog...
Jul 28 19:15:28 dot01-MAIN daemon.err openvpn[1769]: ERROR: Cannot open TUN/TAP dev /dev/net/tun: No such file or directory (errno=2)
UPDATE...
Okay took a break and started looking for a solution and DragonC posted a solution at the bottom. Now I have the new build working. Thanks DragonC for posting a fix!
Router: R7000 (Gateway & WiFi Disabled)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/18)
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: Working
Reset: no (from build 36400M)
Errors: None
Thanks B.S. & Kong for your Work!
Router: R7000 (WiFi Router)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/18)
Kernel: Linux 4.4.145 #586 SMP Sat Jul 28 15:04:24 CEST 2018 armv7l
Status: No Working
Reset: YES (erase nvram then factory defaults)
Errors: Wifi Issues back to Build 35550M
A working WiFi setup from Build 35550M now drops clients with Build 36410M back to Build 35550M.
My WiFi setup on WL0 with 2 VAPs & WL1 with 1 VAPs a total of 5 SSIDs.
Since BS changed mac related code it may be necessary to clear nvram and setup by hand again.
Hello Kong, I erase nvram then factory defaults then configured by hand. Also these commands don't seem to work on this build....
Router: Netgear R8500 (Gateway with WiFi: ON)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/1
Kernel: 4.4.145
Status: Problem with 5 GHz Wireless
Reset: No (upgraded from the previous build via DDUP)
Errors: I can't see the SSID from other devices when in "Mixed" mode on the 5 GHz radios. If I switch from anything other that, I get speeds in the 130mb/s range.
The GUI speed slowness has been fixed on Chrome. Thanks!
Router: DLink DIR-890L (both as routers/ap)
Firmware: DD-WRT v3.0-r36410M kongac (07/28/1
Kernel: 4.4.145
Status: WDS not functional
Reset: No (upgraded from the previous build via GUI)
Last working build for stable WDS is 35550M. I have also tried erasing nvram with builds before this one to no avail. It seems to be something off with wds0.1 not being mapped in Setup -> Networking...and I'm not the only one:
My OpenVPN script from Build 35550M was working fine. Today I was testing Kong's Build 36400M and now 36410M and OpenVPN Client is crashing with the following error in the syslog...
Try to enable OpenVPN server in the Services tab and maybe put some delay into your scripts before it starts executing. BS has been changing the codes that’s controlling the router behaviors and I guess that’s messing up your scripts.
Or as you found out, loading the tun module works as well.
Thanks for the info. I found the Wireless not to be usable with these newer builds and have the Wireless R7000 on build 35550M which allows me to have all devices connecting to any of the 5 SSIDs (3 SSIDs on wl0 & 2 SSIDs on wl1) in my setup.
To turn off and on the Radios I use these commands that Kong provided...
# Radio wl0 off
startservice radio_off_0 -f
# Radio wl1 off
startservice radio_off_1 -f
# Radio wl0 on
startservice radio_on_0 -f
# Radio wl1 on
startservice radio_on_1 -f
These commands work perfectly with Build 35550M but not Build 36410M (only one tested after 35550M). So there something "screwy" with these newer builds and WiFi.
Also, with this Build 36410M there is no MAC issue all the MAC Addresses on all 5 SSIDs are different so it's something else. _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Haven't tried it on this newer build, but on my AC68Us running Kong 35030M if I turn the radio off it hangs within five minutes every time.
I found running 'wl -i <dev> out' which mark the radio down without resetting the driver works fine. <dev> is your wireless device, so eth1 and eth2 on AC68U, wl0/wl1 on some others, etc.
You might also want to do stopservice nas but I don't think it really matters.