Posted: Sun Mar 03, 2024 17:16 Post subject: New Build - 03/03/2024 - r55262
Welcome to Marvell r55262 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Issue/Error 1: First install, had essentially brought to light that the 5Ghz channel (wlan0) had been almost completely brought to a crawl (54mbs speeds) The only variable that seemed to change post reset were the antenna chains setup. Which after a "Reset all Settings" was done, I reconfigured everything, and now (wlan0, 5ghz) is working just fine. If I enable Wlan2, it seems to break the 5ghz again....(Weak strength, and speeds brought down to like older G level ~54Mbs)
Issue/Error 2: I seem to be getting random reboots, and am wondering if maybe the radios are being overloaded by being in decently close proximity (<1meter) to another WAP serving all the same channels, with the addition of wifi6.
I have been perusing the logs, and not really seeing any actual issues, also, I am somewhat of a noob to accessing the router and getting error logs, next to "systemlogs" from the GUI.
I have posted here to ensure the developer can know about the issue, but will soon be dropping the latest FW on to see what happens
Thanks for still keeping this project alive!!! -An appreciative open-source lover / networkingdude.
ALSO: Was unable to access the site for almost a full day (03/27/24) was it down?
P.S. - I would also like to help in any way with the project, and that would include direct feedback, testing out builds, and offering live chat if needed with devs. Please reach out.
Would also like to upgrade, for higher performance, better reliability, so if anyone has suggestions on that front please let me know. (might even just build a custom?)
The 2nd 5GHz WLAN in your WRT3200 is used for DFS / Radar detection purposes in stock firmware.
Enabling WLAN2 / ath2 in DD-WRT is not advised, as it might result in all kinds of problems.
The 2nd 5GHz WLAN in your WRT3200 is used for DFS / Radar detection purposes in stock firmware.
Enabling WLAN2 / ath2 in DD-WRT is not advised, as it might result in all kinds of problems.
Ahhh okay. Thanks! Are there any good resources on more advanced setup / tuning or further explanation of settings that apply to the Linksys WRT3200ACM? I was looking for a good while, and even on the advanced wireless wiki, there seem to be settings that are not listed.
Issue/Error 2: I seem to be getting random reboots, and am wondering if maybe the radios are being overloaded by being in decently close proximity (<1meter) to another WAP serving all the same channels, with the addition of wifi6.
Issue/Error 2: I seem to be getting random reboots, and am wondering if maybe the radios are being overloaded by being in decently close proximity (<1meter) to another WAP serving all the same channels, with the addition of wifi6.
SFE is borked on the new kernel causing this.
Make sure it is disabled
Just wondering, because I've searched around, and can't find what "SFE" is lol. Thanks in advance.