The modem boot without problems, but when it try to load vmlinux.bin.l7, inside script boot:
DD-WRT> fconfig
Run script at boot: true
Boot script:
.. fis load -l vmlinux.bin.l7
.. exec
Enter script, terminate with empty line
>> fis load -l vmlinux.bin.l7
>> exec
>>
Boot script timeout (1000ms resolution): 15
Use BOOTP for network configuration: false
Gateway IP address:
Local IP address:
Local IP address mask:
Default server IP address:
Console baud rate: 9600
GDB connection port: 9000
Force console for special debug messages: false
Network debug at boot time: false
Update RedBoot non-volatile configuration - continue (y/n)? y
... Erase from 0xbffe0000-0xbfff0000: .
... Program from 0x80ff0000-0x81000000 at 0xbffe0000: .
DD-WRT>
there is no response ip address, neither 192.168.1.1 neither 192.168.20.81.
Before execution of script boot, the modem run ok over 192.168.1.1.
I´ve tried to load manually vmlinux.bin.l7, from DD-WRT line command, and this is ok. But nothing about DD-WRT appears.
I´ve reflashed the DIR-300, to test if any errors appears, but nothing....
These is i can see:
Default server: 192.168.1.2
DD-WRT> load -r -b 0x80041000 root.fs
Using default protocol (TFTP)
Raw file loaded 0x80041000-0x802ebfff, assumed entry at 0x80041000
DD-WRT> fis create -b 0x80041000 -f 0xbfc30000 -l 0x002c0000 -e 0x00000000 rootfs
... Erase from 0xbfc30000-0xbfef0000: ............................................
... Program from 0x80041000-0x80301000 at 0xbfc30000: ............................................
... Erase from 0xbffe0000-0xbfff0000: .
... Program from 0x80ff0000-0x81000000 at 0xbffe0000: .
DD-WRT> load -r -b 0x80041000 vmlinux.bin.l7
Using default protocol (TFTP)
Raw file loaded 0x80041000-0x80100fff, assumed entry at 0x80041000
DD-WRT> fis create -r 0x80041000 -e 0x80041000 -l 0x000E0000 vmlinux.bin.l7
... Erase from 0xbfef0000-0xbffd0000: ..............
... Program from 0x80041000-0x80101000 at 0xbfef0000: ............
... Erase from 0xbffe0000-0xbfff0000: .
... Program from 0x80ff0000-0x81000000 at 0xbffe0000: .
DD-WRT> fis create -f 0xbffD0000 -l 0x00010000 -n nvram
... Erase from 0xbffe0000-0xbfff0000: .
... Program from 0x80ff0000-0x81000000 at 0xbffe0000: .
DD-WRT> fconfig boot_script true
boot_script: Setting to true
Update RedBoot non-volatile configuration - continue (y/n)? y
... Erase from 0xbffe0000-0xbfff0000: .
... Program from 0x80ff0000-0x81000000 at 0xbffe0000: .
DD-WRT>
and when i set with fconfig to run this script load:
fis load -l vmlinux.bin.l7
exec
the router start, boot, execute script boot and restart continously as a cycle.....
this is i can see with a simple ping....:
Hardwarefehler.
Hardwarefehler.
Hardwarefehler.
Zeitüberschreitung der Anforderung.
Antwort von 192.168.0.1: Bytes=32 Zeit=14ms TTL=64
Antwort von 192.168.0.1: Bytes=32 Zeit=11ms TTL=64
Zeitüberschreitung der Anforderung.
Zeitüberschreitung der Anforderung.
Zeitüberschreitung der Anforderung.
Zeitüberschreitung der Anforderung.
Zeitüberschreitung der Anforderung.
Zeitüberschreitung der Anforderung.
Hardwarefehler.
Hardwarefehler.
Hardwarefehler.
Hardwarefehler.
Hardwarefehler.
Hardwarefehler.
Hardwarefehler.
Hardwarefehler.
Zeitüberschreitung der Anforderung.
Antwort von 192.168.0.1: Bytes=32 Zeit=22ms TTL=64
Antwort von 192.168.0.1: Bytes=32 Zeit=7ms TTL=64
Zeitüberschreitung der Anforderung.
when the router respond, we can telnet it to stop script.....but when it run.....after 8 other 10 seconds, restart......