DD-WRT Forum :: View topic - Adding USB support into firmware

Quick Links

Log in

Adding USB support into firmware

DD-WRT Forum Forum Index -> Broadcom SoC based Hardware

Goto page Previous 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 Next

View previous topic :: View next topic

Author

Message

braza
DD-WRT User

Joined: 09 Oct 2006
Posts: 105

Posted: Wed Mar 05, 2008 14:40 Post subject:

problem with latest nokaid usb firmware:

umount /dev/scsi/host0/bus0/target0/lun0/part1
mount /dev/scsi/host0/bus0/target0/lun0/part1 /jffs

ok jffs mount with FAT16 only... ext2 and ext3 not mount !

mkdir /jffs/opt
mount -o bind /jffs/opt /opt

Code:

root@DD-WRT:~# sh /tmp/optware-install.sh
Checking system config ...
Using 210.247.16.1 as default gateway.
Using the following nameserver(s):
nameserver 192.168.1.1
Warning: /opt partition not empty!
Installing package uclibc-opt_0.9.28-13_mipsel.ipk ...
Connecting to ipkg.nslu2-linux.org (140.211.167.169:80)
Updating /opt/etc/ld.so.cache
/opt/sbin/ldconfig: can't link /opt/lib/libipkg.so.0 to libipkg.so.0.0.0: Operat
ion not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libpthread.so.0 to libpthread-0.9.28.so:
Operation not permitted
/opt/sbin/ldconfig: can't link /opt/lib/librt.so.0 to librt-0.9.28.so: Operation
not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libnsl.so.0 to libnsl-0.9.28.so: Operati
on not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libc.so.0 to libuClibc-0.9.28.so: Operat
ion not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libintl.so.0 to libintl-0.9.28.so: Opera
tion not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libmudflap.so.0 to libmudflap.so.0.0.0:
Operation not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libstdc++.so.6 to libstdc++.so.6.0.8: Op
eration not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libcrypt.so.0 to libcrypt-0.9.28.so: Ope
ration not permitted
/opt/sbin/ldconfig: can't link /opt/lib/ld-uClibc.so.0 to ld-uClibc-0.9.28.so: O
peration not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libm.so.0 to libm-0.9.28.so: Operation n
ot permitted
/opt/sbin/ldconfig: can't link /opt/lib/libthread_db.so.1 to libthread_db-0.9.28
.so: Operation not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libresolv.so.0 to libresolv-0.9.28.so: O
peration not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libmudflapth.so.0 to libmudflapth.so.0.0
.0: Operation not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libdl.so.0 to libdl-0.9.28.so: Operation
not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libutil.so.0 to libutil-0.9.28.so: Opera
tion not permitted
Installing package ipkg-opt_0.99.163-9_mipsel.ipk ...
Connecting to ipkg.nslu2-linux.org (140.211.167.169:80)
/opt/sbin/ldconfig: can't link /opt/lib/libipkg.so.0 to libipkg.so.0.0.0: Operat
ion not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libpthread.so.0 to libpthread-0.9.28.so:
Operation not permitted
/opt/sbin/ldconfig: can't link /opt/lib/librt.so.0 to librt-0.9.28.so: Operation
not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libnsl.so.0 to libnsl-0.9.28.so: Operati
on not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libc.so.0 to libuClibc-0.9.28.so: Operat
ion not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libintl.so.0 to libintl-0.9.28.so: Opera
tion not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libmudflap.so.0 to libmudflap.so.0.0.0:
Operation not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libstdc++.so.6 to libstdc++.so.6.0.8: Op
eration not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libcrypt.so.0 to libcrypt-0.9.28.so: Ope
ration not permitted
/opt/sbin/ldconfig: can't link /opt/lib/ld-uClibc.so.0 to ld-uClibc-0.9.28.so: O
peration not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libm.so.0 to libm-0.9.28.so: Operation n
ot permitted
/opt/sbin/ldconfig: can't link /opt/lib/libthread_db.so.1 to libthread_db-0.9.28
.so: Operation not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libresolv.so.0 to libresolv-0.9.28.so: O
peration not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libmudflapth.so.0 to libmudflapth.so.0.0
.0: Operation not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libdl.so.0 to libdl-0.9.28.so: Operation
not permitted
/opt/sbin/ldconfig: can't link /opt/lib/libutil.so.0 to libutil-0.9.28.so: Opera
tion not permitted
/tmp/optware-install.sh: line 91: /opt/bin/ipkg: not found
/tmp/optware-install.sh: line 92: /opt/bin/ipkg: not found
/tmp/optware-install.sh: line 93: /opt/bin/ipkg: not found
root@DD-WRT:~#

Sponsor

Eko
DD-WRT Developer/Maintainer

Joined: 07 Jun 2006
Posts: 5772

Posted: Wed Mar 05, 2008 15:06 Post subject:

braza wrote:

hmm, check if jbd and ext3 are loaded.
_________________
Professional debrick service for EU countries for small fee.
Send inquiries to: debrick at dd-wrt dot si

Have a brick you don't need?

Paypal & Amazon.com gift cards are welcome. Every $ or € counts. Email: donate at dd-wrt dot si

mwl
DD-WRT Novice

Joined: 08 Jan 2007
Posts: 1

Posted: Wed Mar 05, 2008 23:01 Post subject:
Great work!!! Thank you. MWL

extasy
DD-WRT Novice

Joined: 30 Oct 2007
Posts: 44

Posted: Thu Mar 06, 2008 13:31 Post subject:

shinji257 wrote:

Just curious but what does ftdi_sio.o provide?

My USB device needs it when using kernel 2.4. It should be enough with the other module but it just don't seem to do the job by itself.
more information:
http://ftdi-usb-sio.sourceforge.net/#1

Thank you for all your help! If you would make a script for auto mounting hdd that would have been really nice! What I'm dreaming of is a all included mega usb build with all goodies that is usable for ppl like me with 8MiB routers.

Feb 27 21:19:41 kernel: usbserial.c: USB Serial support registered for FTDI SIO
Feb 27 21:19:41 kernel: usbserial.c: USB Serial support registered for FTDI 8U232AM Compatible
kernel: usbserial.c: USB Serial support registered for FTDI FT232BM Compatible
kernel: usbserial.c: FTDI FT232BM Compatible converter detected
kernel: usbserial.c: FTDI FT232BM Compatible converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
kernel: usbserial.c: USB Serial support registered for FTDI FT2232C Compatible
kernel: usbserial.c: USB Serial support registered for FTDI FT232R Compatible
kernel: usbserial.c: USB Serial support registered for USB-UIRT Infrared Tranceiver
kernel: usbserial.c: USB Serial support registered for Home-Electronics TIRA-1 IR Transceiver
kernel: ftdi_sio.c: v1.3.5r1:USB FTDI Serial Converters Driver

Eko
DD-WRT Developer/Maintainer

Joined: 07 Jun 2006
Posts: 5772

Posted: Fri Mar 07, 2008 7:29 Post subject:

braza wrote:

Try
mount -t ext2 .....
_________________
Professional debrick service for EU countries for small fee.
Send inquiries to: debrick at dd-wrt dot si

Have a brick you don't need?

Paypal & Amazon.com gift cards are welcome. Every $ or € counts. Email: donate at dd-wrt dot si

braza
DD-WRT User

Joined: 09 Oct 2006
Posts: 105

Posted: Fri Mar 07, 2008 9:21 Post subject:
"mount -t ext2" on other firwares version I get all my memory device.. Jffs..mmc..usb..bla...bla..bla.. ! In nokaid usb firmware send the command "mount -t ext2" is nothing ! root@DD-WRT:~# mount -t ext2 root@DD-WRT:~# mount -t ext2 root@DD-WRT:~#

shinji257
DD-WRT User

Joined: 02 May 2007
Posts: 222

Posted: Fri Mar 07, 2008 9:24 Post subject:
You still need to specify mount point and device! Example: mount -t ext2 /dev/discs/disc0/part1 /mnt

braza
DD-WRT User

Joined: 09 Oct 2006
Posts: 105

Posted: Fri Mar 07, 2008 9:34 Post subject:
Yes,... Try.. nothing ! Only on previos firmware its works !

shinji257
DD-WRT User

Joined: 02 May 2007
Posts: 222

Posted: Fri Mar 07, 2008 9:35 Post subject:
Hmm... When I get a chance I will load eko's latest build and try it myself. I've been kinda busy with other things lately.

braza
DD-WRT User

Joined: 09 Oct 2006
Posts: 105

Posted: Fri Mar 07, 2008 9:38 Post subject:

PART1 is ext2

PART2 is FAt16

Code:

DD-WRT v24 std (c) 2008 NewMedia-NET GmbH
Release: 03/05/08 (SVN revision: 9235)

DD-WRT login: root
Password:
==========================================================

____ ___ __ ______ _____ ____ _ _
| _ \| _ \ \ \ / / _ \_ _| __ _|___ \| || |
|| | || ||____\ \ /\ / /| |_) || | \ \ / / __) | || |_
||_| ||_||_____\ V V / | _ < | | \ V / / __/|__ _|
|___/|___/ \_/\_/ |_| \_\|_| \_/ |_____| |_|

DD-WRT v24
http://www.dd-wrt.com

==========================================================

BusyBox v1.9.0 (2008-03-05 12:29:44 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

root@DD-WRT:~# umount /dev/scsi/host0/bus0/target0/lun0/part1
root@DD-WRT:~# mount -t ext2 /dev/scsi/host0/bus0/target0/lun0/part1 /jffs
root@DD-WRT:~# df
Filesystem 1k-blocks Used Available Use% Mounted on
rootfs 2880 2880 0 100% /
/dev/root 2880 2880 0 100% /
/dev/mtdblock/4 4160 324 3836 8% /jffs
root@DD-WRT:~# mount /dev/scsi/host0/bus0/target0/lun0/part2
root@DD-WRT:~# mount /dev/scsi/host0/bus0/target0/lun0/part2 /jffs
root@DD-WRT:~# df
Filesystem 1k-blocks Used Available Use% Mounted on
rootfs 2880 2880 0 100% /
/dev/root 2880 2880 0 100% /
/dev/mtdblock/4 16040 11376 4664 71% /jffs
/dev/scsi/host0/bus0/target0/lun0/part2
16040 11376 4664 71% /jffs
root@DD-WRT:~#

braza
DD-WRT User

Joined: 09 Oct 2006
Posts: 105

Posted: Fri Mar 07, 2008 9:47 Post subject:
@shinji257 You live in Japan ?? I live and have one question about HIKARI FIRE "NTT"!

shinji257
DD-WRT User

Joined: 02 May 2007
Posts: 222

Posted: Fri Mar 07, 2008 9:48 Post subject:
no. i do not live in japan.

braza
DD-WRT User

Joined: 09 Oct 2006
Posts: 105

Posted: Fri Mar 07, 2008 9:56 Post subject:

@shinji257. ok thank you !

Code:

root@DD-WRT:~# lsmod
Module Size Used by
ip_nat_pptp 2284 0 (unused)
ip_conntrack_pptp 2812 1
ip_nat_proto_gre 1552 0 (unused)
ip_conntrack_proto_gre 2440 0 [ip_nat_pptp ip_conntrack_pptp]
jffs2 153624 1
printer 9852 0 (unused)
vfat 11692 0
fat 36840 0 [vfat]
ext3 72724 0
jbd 54328 0 [ext3]
usb-storage 34072 0
sd_mod 12500 0
scsi_mod 95720 2 [usb-storage sd_mod]
usb-ohci 19060 0 (unused)
usbcore 76344 0 [printer usb-storage usb-ohci]
root@DD-WRT:~#

jnjn
DD-WRT User

Joined: 07 Jun 2006
Posts: 428
Location: PRC

Posted: Sat Mar 08, 2008 15:57 Post subject:

for someone who would like to get a better experience in usb printer support using p910nd, please use the attached binary instead of that old version 0.7-1 which ipkg installed from that old openwrt package repository. Wink

p910nd.zip

Description:

v 0.91 of p910nd.
works fine with present canon pixma ip1xxx printers.

Download

Filename:

p910nd.zip

Filesize:

4.69 KB

Downloaded:

590 Time(s)

Bird333
DD-WRT Guru

Joined: 07 Jun 2006
Posts: 803

Posted: Sat Mar 08, 2008 16:50 Post subject:
which directory do I put this in? I got p910nd in '/jffs/usr/sbin', and /jffs/etc/init.d. Will this finally allow bidirectional communication?

Goto page Previous 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 Next

Display posts from previous:

Page 6 of 10

DD-WRT Forum Forum Index -> Broadcom SoC based Hardware

All times are GMT

Navigation

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum