Thanks modervador, this is for all who have wanted these features but didn't have the room. Tested on a usr5461, works good but I don't have a printer to test. Flash and post your issues or thoughts.
Hi autobot,
I gave this a try but it doesn't seem to work for me at all. I can only access the router admin webpage if its not connected to WAN and I'm connecting via wireless. Using other USR5461 builds work fine, but this one in particular does not work for me.
anyone else experience this?
Just a bit more detail:
I gave this a try twice. The first time, was the very first time I flashed my USR5461. I flashed from the original firmware to the one posted above using the web interface (I compiled tsr2usr for windows and ran it on the provided bin file first). It wasn't stable (being connected to WAN, and having LAN connections caused dd-wrt web gui to not be usable) so I flashed it (using dd-wrt web interface with no devices connected other than a single wireless client) to a different version (generic) that did work. I tried to flash again to the above bin, but the dd-wrt web interface complained about the file being invalid. So I flashed it using the alternative method (ping, unplug, uplad via tftp). The web interface again was unusable when WAN and LAN connections were connected, so I just reflashed it back to generic.
Where you using autoap when this happened? And which generic version gives you no problems as I have the same router and I always like the VINT builds from Eko but made this NEWD for those who have Asus units. _________________ Eko Builds
Searching for autoap on dd-wrt, it seems like it has to be manually enabled (maybe I'm wrong). So if that's the case, autoap was disabled. If I have to disable it by running a script, then I missed that step.
Thanks modervador, this is for all who have wanted these features but didn't have the room. Tested on a usr5461, works good but I don't have a printer to test. Flash and post your issues or thoughts.
Hi autobot,
I gave this a try but it doesn't seem to work for me at all. I can only access the router admin webpage if its not connected to WAN and I'm connecting via wireless. Using other USR5461 builds work fine, but this one in particular does not work for me.
anyone else experience this?
Just a bit more detail:
I gave this a try twice. The first time, was the very first time I flashed my USR5461. I flashed from the original firmware to the one posted above using the web interface (I compiled tsr2usr for windows and ran it on the provided bin file first). It wasn't stable (being connected to WAN, and having LAN connections caused dd-wrt web gui to not be usable) so I flashed it (using dd-wrt web interface with no devices connected other than a single wireless client) to a different version (generic) that did work. I tried to flash again to the above bin, but the dd-wrt web interface complained about the file being invalid. So I flashed it using the alternative method (ping, unplug, uplad via tftp). The web interface again was unusable when WAN and LAN connections were connected, so I just reflashed it back to generic.
Where you using autoap when this happened? And which generic version gives you no problems as I have the same router and I always like the VINT builds from Eko but made this NEWD for those who have Asus units.
@modervador: your firmware is not stable, very slow and i can't see USB support in services ,
@autobot:i need usb print server and AP, repeater mode or client mode maybe usb storage .That's all.you can remove VLANs,Security,access restrictions,NAT&QoS to have room.thanks so much.now i'm using micro bulid 12533,it's very good.thanks again
did you clear the nvram to get this working? i tried to install it out of the box, but maybe i missed a step?
sogoku_vn wrote:
@modervador: your firmware is not stable, very slow and i can't see USB support in services ,
@autobot:i need usb print server and AP, repeater mode or client mode maybe usb storage .That's all.you can remove VLANs,Security,access restrictions,NAT&QoS to have room.thanks so much.now i'm using micro bulid 12533,it's very good.thanks again
yes,i did it but no happen .no USB support in Services.should i install to JFFS using ipkg and then loaded (using insmod) from a startup script to enable USB support?
You must have me confused with somebody else. My firmware is quite stable, with uptimes measured in years. It is very unlikely that you have used it, as it serves a very small market segment of about 10 systems. I haven't had to make a new build in about 7 years, which was when the newest system was put into service. It definitely hasn't been compiled to run on Broadcom routers.
In this firmware usb is enabled by default(no webif), plugin a usb hard drive and issue the command mount -o noatime,nodiratime /dev/disks/disk0/part1 /mnt and you would change the part1 to which ever partition your ext2 is. Printing is also ready to go(no webif), plug in a usb printer and read the manual on using p910nd by googling for it. Autoap is used by issuing the command autoap. I'm busy, but will try to make a better build when I get time. Perhaps using some of fraters auto mounting scripts and such. _________________ Eko Builds
In this firmware usb is enabled by default(no webif), plugin a usb hard drive and issue the command mount -o noatime,nodiratime /dev/disks/disk0/part1 /mnt and you would change the part1 to which ever partition your ext2 is. Printing is also ready to go(no webif), plug in a usb printer and read the manual on using p910nd by googling for it. Autoap is used by issuing the command autoap. I'm busy, but will try to make a better build when I get time. Perhaps using some of fraters auto mounting scripts and such.
Maybe if anyone is willing and able, the filename could be changed to add the "plus" in there to prevent confusion.
PS: If anyone can answer this quick easy question, I'd appreciate it...
I'm getting ready to do the CFE compression on my 2mb WRT54Gv8 so I can use micro-plus. All I want is the expanded command set, SSH, and AutoAP. If I install one of the *NEWD_micro-plus_ssh builds, will there be room to install the AutoAP script with or without the AutoAP GUI? I am aware the CGI isn't working after 12533 - I haven't decided which way to go with that yet.
EDIT:
Why does the firmware within the zip in the OP have a .trx extension? Can this simply be changed to .bin before flashing, or is this something special?
That's a great idea, FYI there is no ssh in my firmware as it had to be removed to make room for the other things, telnet is still in there though. Yes there is room for autoap, yes you can rename the .trx to .bin. _________________ Eko Builds