[GeneJin]

Hi, any support for DIR-685 yet?

Thanks,
Eugene

[bbb_forever]

[Sash]

[lativ2]

Hi,
hire is link to tech spec,

Looks good :
The DIR-685 has 64 MB of RAM and 32 MB of flash and a 2x2 draft 802.11n radio based on a Ralink RT2880F 2T3R MAC/BB and RT2850L 2.4/5 GHz 2T3R transceiver. The radio, however, is locked to single-band 2.4 GHz operation. The processor could not be determined due to a soldered-in radio module over an RF shield. It does not appear Ubicom-based, however, since Ubicom's signature automatic QoS features are not present in the 685.


http://www.dslreports.com/forum/r22607966-DLinks-new-DIR685-is-speed-daemon[

[dalelovelace]

Posted on the back of the DIR-685 router, and on the inside, is FCC-ID RRK-WMPND02A1. I checked this FCC-ID at FCC.gov and it doesn't show up.

Since the radio module is soldered in over the CPU you can't tell what it is by examination, however according to a post on dsl-reports it seems to be a Ralink RT2880F PU 266MHz with 64MB RAM and 32MB Flash.

I'm linking several hi res pictures I took of the insides to see if this will help. I have one of these that I'm not using right now as I have replaced it with a Belkin that will run dd-wrt! Will be happy to try any build on it if someone is nice enough to try one. I don't have a jtag cable, but I'm going to order one today so I can get more info on this great router.

http://daleandkim.com/DIR-685-receiver-side.jpg
http://daleandkim.com/DIR-685-switchside.jpg
http://daleandkim.com/DIR-685-chip1.jpg
http://daleandkim.com/DIR-685-chip2.jpg
http://daleandkim.com/DIR-685-chip3.jpg

[samurai123]

Besides the RF module, it has Cortina CS3516 SoC.

[Sash]

[olympuse-FC]

[pintoyac]

How much money would be needed to buy this router? I have no problem donating in order for it to be supported, D-Link's firmware is a joke

[chengsheng16]

[Jivatman]

I found GPL sources for DIR-685

ftp://gpl.dlink.com/DIR-685/DIR-685_GPL_061709.tgz

[lokistrategiesinc]

[Sash]

we need a serial port log.

[lokistrategiesinc]

I own a DIR-685. What is a Serial Port Log(sorry I'll Google it later), and how can I get it?

[samurai123]

Here is the serial port log

ILI9322_init......
Enabling TVE controller
@@===in gpio0_16high value 110000

Storlink SL351x Boot Loader [Linux2], version 1.0.9
Built by linux, 11:45:14, Jun 30 2009

Alpha version v0.5 SVN Revision 147

Processor: SL3516c3
CPU Rate: 300000000
AHB Bus Clock:150MHz Ratio:2/1
MAC 1 Address: 00:xx:yy:zz:xx:yy
MAC 2 Address: 00:xx:yy:zz:yy:zz
inet addr: 192.168.0.1/255.255.255.0
==> enter ^C to abort booting within 1 seconds ......
Load kernel from 0x30040000 to 0x1600000 size 11866304
v3 check
Image header (0x00000024):
magic : 0x20080321
size : 11866144 (0xb51020)
offset : 0x00000000
devname: '/dev/mtdblock/1'
digest : Advance to next block : offset=11866304(0xb510c0), size=11866304(0xb510c0)
Uncompressing Linux...7zip decompressing ...

7zip decompress success

done, booting the kernel.

FTC_FOTG2XX : registered host c7c7cc00

FTC_FOTG2XX_1 : registered host c7c7c400

test_interrupt interrupt


init started: BusyBox v1.00 (2009.07.27-14:12+0000) multi-call binary

Starting pid 393, console /dev/console: '/etc/init.d/rcS'
[/etc/init.d/S03config.sh]
Mounting proc and var ...
Using /lib/modules/ufsd.ko
ufsd: module license 'Commertial product' taints kernel.

ufsd: driver loaded

UFSD version 6.1 (Jul 31 2007, 21:51:29)

NTFS read/write support included

$Id: ufsdvfs.c,v 1.109 2007/07/31 12:01:57 shura Exp $

ufsd: address 0xbf000000

Starting udevd...
Starting udevstart...
Starting udevstart...
Start xmldb ...
[/etc/scripts/misc/profile.sh] get ...
[/etc/scripts/misc/defnodes.sh] ...
[/etc/defnodes/S10setext.sh] ...
PHP [/etc/defnodes/S11setnodes.php] ...
PHP [/etc/defnodes/S12features.php] ...
PHP [/etc/defnodes/S13flashspeed.php] ...
[/etc/defnodes/S14wps_upnp.sh] ...
PHP [/etc/defnodes/S20setnodes.php] ...
devdata: not found
VFS: Can't find ext3 filesystem on dev mtdblock5.

VFS: Can't find an ext2 filesystem on dev mtdblock5.

FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

FAT: invalid media value (0xbb)

VFS: Can't find a valid FAT filesystem on dev mtdblock5.

FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

FAT: invalid media value (0xbb)

VFS: Can't find a valid FAT filesystem on dev mtdblock5.

SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock5

ufsd: failed to mount mtdblock5

mount: Mounting /dev/mtdblock/5 on /www/locale/alt failed: Invalid argument
PHP [/etc/defnodes/S40brand.php] ...
PHP [/etc/defnodes/S42features.php] ...
[/etc/scripts/misc/defnodes.sh] Done !!
[/etc/templates/timezone.sh] ...
zone : 5
gen :
[/etc/templates/logs.sh] ...
[/var/run/logs_run.sh] ...
Using /lib/modules/nas_gpio_access.ko
nas_gpio Access Init.

start fresetd ...
Inserting modules ...
Using /lib/modules/ifresetcnt.ko
Network interface reset count v1.0

Factory reset time : 5 secs
System reset time : 2 secs
Storlink eth0 address = 00265A23166A

Can't find version control

GMAC-0 Flow Control Enable.

Storlink eth0 address = 00265A23166A

Enable MAC Flow Control...

set interrupt f

Storlink eth1 address = 00265A23166B

Can't find version control

GMAC-1 Flow Control Enable.

Storlink eth1 address = 00265A23166B

Enable MAC Flow Control...

[/etc/templates/webs.sh] start ...
[/var/run/webs_start.sh] ...
Starting HTTPD ...
[/etc/init.d/S03config.sh] done!
[/etc/init.d/S10system.sh]
start scheduled ...
[/etc/templates/scheduled.sh] start ...
[/var/run/scheduled_start.sh] ...
Start scheduled ...
setup layout ...
[/etc/scripts/layout.sh] ...
[/var/run/layout_start.sh] ...
Start router layout ...
device eth0 entered promiscuous mode

br_stp_recalculate_bridge_id: p->dev->dev_addr[0]-[5]= 0:26:5a:23:16:6a

interface ra0 does not exist!
joel disable stun ..
[/etc/scripts/network_usb.sh] start...
insmod: /lib/modules/2.6.15: No such file or directory
Using /lib/modules/sxuptp.ko
alloc success ffc7c000 dma 7560000

alloc success ffc9c000 dma 7580000

insmod: /lib/modules/2.6.15: No such file or directory
Using /lib/modules/sxuptp_generic.ko
usbcore: registered new driver sxuptp_generic

insmod: /lib/modules/2.6.15: No such file or directory
Using /lib/modules/jcp.ko
insmod: /lib/modules/2.6.15: No such file or directory
Using /lib/modules/jcp_cmd.ko
start LAN ...
[/etc/templates/lan.sh] ...
[/var/run/lan_start.sh] ...
Start LAN (br0/192.168.0.1/255.255.255.0)...
Start DHCP server (br0) ...
Start igmp ...
[/etc/templates/igmpproxy.sh] start ...
[/var/run/igmpproxy_start.sh] ...


igmp snooping is disabled ...

IGMP proxy is not enabled!
enable LAN ports ...
[/etc/scripts/enlan.sh] ...
!!!!!!!!!!!!!!! TODO [/etc/scripts/enlan.sh] !!!!!!!!!!!!!!
start WLAN ...
[/etc/templates/wlan.sh] start ...
[/etc/templates/wifi/wlan_sch.sh] stop ...
Hello from hostapd.ra0.conf
[/var/run/wlan_start.sh] ...
Start WLAN interface ra0 ...
[/etc/templates/wps.sh] pre_setie ...
GMAC-1 link down

restart WLAN driver ...
Using /lib/modules/rt2880_iNIC.ko
RT2880 iNIC: 802.11n WLAN PCI driver v2.0.0.0 (Jan. 15, 2009)

RT2880 iNIC: pci dev 0000:00:0c.0 (id 1814:0801 rev 00)

PCI: enabling device 0000:00:0c.0 (0140 -> 0142)

rt->regs = ca820000

===> Get MAC from iNIC

============= Init Thread ===================

RacfgTaskThread pid = 761

RacfgBacklogThread pid = 762

ra0: Ralink iNIC at 0xca820000, 00:43:0c:00:00:00, IRQ 67

SIOCSIFTXQLEN: No such device
/proc/net/br_forward_br0: cannot create
Start WLAN interface ra0 Done !!!
[/etc/templates/wifi/wlan_sch.sh] start ...
[/var/run/wlan_sch_start.sh] ...
[/etc/templates/wifi/wlan_sch_run.sh] restart ...
[/var/run/wlan_sch_run_start.sh] ...
Start WLAN layout ...
device ra0 entered promiscuous mode

br_stp_recalculate_bridge_id: p->dev->dev_addr[0]-[5]= 0:43: c: 0: 0: 0

br_stp_recalculate_bridge_id: p->dev->dev_addr[0]-[5]= 0:26:5a:23:16:6a

[/etc/templates/wps.sh] setie ...
Using specified config file : /var/run/wps.config
Configuration file: /var/run/hostapd.ra0.conf
iNIC Open ra0

BssidNum=1

ADDR0 = 58000008, ADDR1 = 58100008

CMD = 0156, STATUS = 04a0

LATENCY = 00, CACHE LINE SIZE = 08

INT LINE = 67

Reset Card

ADDR0 = 58000008, ADDR1 = 58100008

CMD = 0156, STATUS = 04a0

INT LINE = 67

### LATENCY = 20, CACHE LINE SIZE = 08

PDMA_RST_IDX = 0

PDMA_GLO_CFG = 00000020

TX_MAX_CNT0 = 00000080

2. reg = 00000020

2. PDMA_GLO_CFG = 0000006d, reg = 00000065

RACFG_CMD_BOOT_NOTIFY

Op mode = 1

Wait for boot done...

Open file: /etc/Wireless/RT2880/iNIC_ap.bin

Open file: /var/run/RT2880AP.dat

RACFG_CMD_BOOT_NOTIFY

Open file: /etc/Wireless/RT2880/iNIC_ap.bin

Open file: /var/run/RT2880AP.dat

RACFG_CMD_BOOT_INITCFG(0)

RACFG_CMD_BOOT_INITCFG(0)

Send Init Cfg Data Done(1 packets)

WARNING! iNIC profile ack sequence 0<->-1 mismatched,duplicated packet? ignore...

RACFG_CMD_BOOT_UPLOAD(0)

RACFG_CMD_BOOT_UPLOAD(1)

RACFG_CMD_BOOT_UPLOAD(2)


CRC:01 08 14 18 49 86 1c 7f 22 32 2e 30 2e 30 2e 30 22 00 00 00 32 30 30 39 30 33 31 30 00 00 00 00 00 00 00 00 78 83 07 00

Send RT2880 Firmware Done

===================================

version: "2.0.0.0"

size: 492408 bytes

date: 20090310

===================================


Send STARTUP to RT2880

Close Firmware file

RACFG_CMD_BOOT_STARTUP

Update MAC(0)=00:26:5a:23:16:6a

ralink_init: Initiating ralink_wireless_event_init...
Using interface ra0 with hwaddr 00:26:5a:23:16:6a and ssid 'Gate'
=>=>=> set ssid to Gate
start Application ...
[/usr/sbin/submit] GROUP_ADD ...
GMK - hexdump(len=32): cc cc f8 67 68 90 28 94 5b 9f 2d 54 d6 b4 3e c5 0f a1 c7 d2 0d 68 14 41 be fd ba 4e 81 51 43 bc
GTK - hexdump(len=32): f4 ae 0b 6c b8 44 a3 6a f9 1b 91 ef 0c 2c 31 21 1d 41 dc 1b 3e 53 75 7a 8b 05 b3 0b 38 e9 f0 96
hostapd_setup_interface: return 0
[/usr/sbin/submit] USER_ADD ...
[/usr/sbin/submit] PURE-FTPD ...
[/etc/templates/user.sh] ...
[/usr/sbin/submit] NET_ACCESS ...
[/etc/templates/pure_ftpd.sh] ...
[/var/run/user_add.sh] ...
rm: cannot remove `/var/smbpasswd[/etc/templates/group.sh] ...
[/var/run/group_add.sh] ...
': No such file or directory
Start smbd...
[/usr/sbin/submit] UPNP_AV_START ...
[/usr/sbin/submit] ITUNES_START ...
[/etc/templates/upnp_av.sh] ...
pure_ftpd is disabled !
[/var/run/upnp_av_start.sh] ...
No: [/var/run/prescan_start.sh] ...
[/etc/templates/network_access.sh] ...
not found
Upnp-av server is disabled !
[/usr/sbin/submit] BT_START ...
[/etc/templates/itunes_server.sh] ...
start Guest Zone
[/etc/templates/bt.sh] ...
[/etc/templates/gzone.sh] ...
[/var/run/bt_start.sh] ...
generate_start !
BT is disabled !
[/var/run/itunes_server_start.sh] ...
No: not found
[/var/run/gzone_start.sh] ...
[/var/run/network_access_start.sh] ...
Start smbd...
[/etc/templates/enable_gzone.sh] ...
[/var/run/enable_gzone_start.sh] ...
start RG ...
add passwd from file
[/etc/templates/rg.sh] start ...
[/var/run/rg_start.sh] ...
startsmbfilepwent_internal: file /var/smbpasswd did not exist. File successfully created.
Added user nobody.
Using /lib/modules/ifresetcnt.ko
insmod: cannot insert `/lib/modules/ifresetcnt.ko': File exists (-1): File exists
insmod: /lib/modules/2.6.15: No such file or directory
insmod: ip_conntrack_ike_m.ko: no module by that name found
insmod: /lib/modules/2.6.15: No such file or directory
insmod: ip_conntrack_esp_m.ko: no module by that name found
insmod: /lib/modules/2.6.15: No such file or directory
insmod: ip_conntrack_proto_esp_m.ko: no module by that name found
insmod: /lib/modules/2.6.15: No such file or directory
insmod: ip_nat_proto_esp_m.ko: no module by that name found
iptables: No chain/target/match by that name
sendto_unsock(/var/run/portt.unixsocket, flush)
/proc/sys/net/ipv4/arp_flood_burst: cannot create
/proc/sys/net/ipv4/arp_flood_cost: cannot create
start DNRD ...
[/etc/templates/dnrd.sh] ...
[/var/run/dnsmasq_start.sh] ...
Start Dnsmasq ...
Start telnetd ...
start UPNPD ...
[/etc/templates/upnpd.sh] ...
[/var/run/upnpd_start.sh] ...
Starting UPnP ...
[/var/run/upnp_alive.sh] ...
start WAN ...
Set WAN port media type 0
rtl8366rb_setEthernetPHY port 4 type 0

[/etc/templates/wan.sh] start ...
[/var/run/wan_start.sh] ...
insmod: /lib/modules/2.6.15: No such file or directory
insmod: sw_tcpip.ko: no module by that name found
It is the DHCP mod start!!
Storlink eth1 address = 001E37DA242F

Can't find version control

GMAC-1 Flow Control Enable.

Storlink eth1 address = 001E37DA242F

Enable MAC Flow Control...

Clone WAN MAC : 00:aa:bb:cc:dd:ee
DHCP client on WAN(eth1) CloneMAC(00:aa:bb:cc:dd:ee) ...
start LLD2D ...
[/etc/templates/lld2d.sh] ...
[/var/run/lld2d_start.sh] ...
Start LLD2 daemon ...
start fcrss_server ...
[/etc/templates/fcrss_server.sh] start...
GMAC-1 link down

start Neaps ...
[/etc/templates/neaps.sh] start ...
[/var/run/neaps_start.sh] ...
Start Neap Server ...
start igmpproxy ...
[/etc/templates/igmpproxy.sh] start ...
[/var/run/igmpproxy_stop.sh] ...
IGMP proxy is not started !
[/var/run/igmpproxy_start.sh] ...


igmp snooping is disabled ...

IGMP proxy is not enabled!
start LCD Display ...
[/etc/templates/lcd_display.sh] ...
start Wake on LAN ...
[/etc/init.d/S10system.sh] done!
[/etc/templates/wol.sh] ...
rcS done!

Starting pid 1308, console /dev/console: '/bin/sh'


BusyBox v1.00 (2009.07.27-14:12+0000) Built-in shell (msh)