But after flashing, I think it's bricked~ The Lan light was keeping on and off after power was on. I would try to un-bricked.
BTW,I was still wondering which version of dd-wrt should flash on my router~
@tzjwxpre
sorry for the bricking.
All my steps are under serial console. If you find your router serial pin define and have the connector, you may try my steps.
I post my steps to unbrick below.
2. Connect the serial and run terminal utility,(57600)
3.Power on the router, and enter the uboot (press "4").
This is my uboot message (I bulid my own uboot)
Code:
U-Boot 1.1.3 (Mar 19 2010 - 10:55:07)
Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81fb0000
flash_protect ON: from 0xBF000000 to 0xBF01D3C3
flash_protect ON: from 0xBF030000 to 0xBF030FFF
============================================
Ralink UBoot Version: 3.3
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 256 Mbits SDR
DRAM bus: 32 bit
Total memory: 64 MBytes
Flash component: NOR Flash
Date:Mar 19 2010 Time:10:55:07
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 384 MHZ ####
SDRAM bus set to 32 bit
SDRAM size =32 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
1
You choosed 4
4: System Enter Boot Command Line Interface.
U-Boot 1.1.3 (Mar 19 2010 - 10:55:07)
RT3052 #
You may check the env setting by enter "printenv"
This is mine.
Thanks! It's unbricked. I flashed bk to ralink firmware 3.3.0.0.
Now, I am still seraching a version of dd-wrt with USB port working! I've tried your suggesion (asus-rtn13u version) but can't work. Lan port will keep on and off. If you get any idea for me, please advise me~
I setted Tx Power to 25 and it still acts like as 71. I read somewhere that Ralink datasheet is 14Dbm, which is 25mW.
Secondly, I'm currently using it at dd-wrt Repeater Bridge mode, attached to my main router via wireless, and works flawlassly. But When I restart my main router, dd-wrt don't connects automatically again, I have to restart dd-wrt manually(power off/on). Are there anything I can do?
does anybody have boot loader file that I can use? I have a Ralink RT3052 with a Ralink RT2860V2 wireless interface (not sure about the wireless interface) bought form dealextreme. The same router as mention in the first post in this thread.
Joined: 10 May 2008 Posts: 1380 Location: Pacific North West, USA
Posted: Sat May 22, 2010 10:41 Post subject:
Fixx wrote:
I setted Tx Power to 25 and it still acts like as 71. I read somewhere that Ralink datasheet is 14Dbm, which is 25mW.
Secondly, I'm currently using it at dd-wrt Repeater Bridge mode, attached to my main router via wireless, and works flawlassly. But When I restart my main router, dd-wrt don't connects automatically again, I have to restart dd-wrt manually(power off/on). Are there anything I can do?
1) I don't know if the TX power adjusting up/down actually works. I have my AP/RB's set @ 100mw but have no way to tell actual power output. It has not affected performance - i.e. - there has been no degradation of router operation
2) I have to do the same. I reboot the main AP, I have to power cycle the RB - I think it will connect on its own, but I thought I read somewhere it could take up to 5-10 minutes to re-connect on its own. Maybe sometime when I'm bored I'll try and test out if this is true or not. _________________ Soylent Green Is People !
=-=-=-=-=-=-=-=-=-=-=
Netgear Nighthawk R7000 - DD-WRT Build R46220
Linksys EA8500 - OpenWRT IPQ806x Trunk R16375 5.4 Kernel
weird note
couple days ago i flashed build 14311 and today router acted akward. using cable, everything was ok but when i used Wifi whole LAN connection was about 5-6kbit/s. made couple "nvram erase" and "factory default"s but nothing good. then flashed again 14311 but still nothing
then i got pissed off and flashed 14144 and everything is OK
Joined: 10 May 2008 Posts: 1380 Location: Pacific North West, USA
Posted: Thu Jun 03, 2010 12:53 Post subject:
Yeah, I have a couple extra WHR-G300N's for 'testing'
14144 seems to be the current stable build for these.
Newer builds are sort of acting flaky.
14144 is fine for me, but others are still reporting I-Phone / I-Touch issues. _________________ Soylent Green Is People !
=-=-=-=-=-=-=-=-=-=-=
Netgear Nighthawk R7000 - DD-WRT Build R46220
Linksys EA8500 - OpenWRT IPQ806x Trunk R16375 5.4 Kernel
if I m not wrong, is this floppy power connector? _________________ 1X Unbranded Ralink SoC RT3052 based router (Dead)
1X Wippies Wifibox
1X TP-Link WR-1043ND
Joined: 10 May 2008 Posts: 1380 Location: Pacific North West, USA
Posted: Sat Jun 26, 2010 10:48 Post subject:
ATVATOR,
How did you flash that wive-ng firmware to the WHR-G300N?
I've tried multiple builds - it won't flash.
Did you have to hex-edit the file? _________________ Soylent Green Is People !
=-=-=-=-=-=-=-=-=-=-=
Netgear Nighthawk R7000 - DD-WRT Build R46220
Linksys EA8500 - OpenWRT IPQ806x Trunk R16375 5.4 Kernel