Posted: Tue Mar 16, 2010 15:33 Post subject: D-Link DIR-300 Rev. A zerschossen?
Hallo,
ich habe einen D-Link DIR-300 Rev. A.
Nun kam ich auf die Idee die aktuelle Stable von DD-WRT zu flashen ueber die redboot variante.
Habe es nach der Anleitung hier in der Datenbank gemacht und alles hat auch wunderbar funktioniert.
Nach dem letzten Schritt faehrt jedoch das System nicht mehr richtig hoch scheinbar.
Der Router ist kurz ueber 192.168.1.1 fuer 4-5 Pings anpingbar bekommt dann aber einen Timeout. Nach 30-60 Sekunden das selbe spiel wieder von vorne.
Kein Webinterface garnix...
Jetzt das dumme. Ich kann ploetzlich auch nicht mehr ueber den wan port per telnet connecten(redboot).
Habe ich den Router jetzt zerschossen?
Was kann ich tun?
Wie das, wenn ich nicht an den Bootloader komme?
Keine Konsole - kein Reflash. Das war auch meine erste Idee.
Habe schon daran gedacht mich an den seriellen port zu hängen, möchte das Gerät aber ungerne aufschrauben.
Nun habe ich ihn aufgeschraubt und mir pins an den seriellen port gelötet, ich komme hier so nicht weiter...
Habe ein altes Siemens Handykabel zum connecten mit dem pc genommen.
Code:
+... waiting for BOOTP information
Can't get BOOTP info, using default IP address
Ethernet eth0: MAC address xx:xx:xx:xx:xx:xx
IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.1.1
RedBoot(tm) bootstrap and debug environment [ROMRAM]
production release, version "2.1.3" - built 18:43:19, Sep 20 2007
Platform: ap61 (Atheros WiSOC)
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
Copyright (C) 2007, NewMedia-NET GmbH.
Board: DLINK DIR-300
RAM: 0x80000000-0x81000000, [0x80040580-0x80fe1000] available
FLASH: 0xbfc00000 - 0xbfff0000, 64 blocks of 0x00010000 bytes each.
== Executing boot script in 4.000 seconds - enter ^C to abort
DD-WRT> fis load -l linux
Image loaded from 0x80041000-0x802d0c58
DD-WRT> exec
Now booting linux kernel:
Base address 0x80030000 Entry 0x80041000
Cmdline :
Code:
CPU revision is: 00019064
mem setup
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Built 1 zonelists in Zone order. Total pages: 4064
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashfs noinitrd mem=16M
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 64 (order: 6, 256 bytes)
Using 92.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13060k/16384k available (2203k kernel code, 3324k reserved, 292k data, 124k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Found board config at 0xa83f0000
Radio config found at offset 0xf8(0x1f8) (a83f00f8)
Generic PHY: Registered new driver
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
gpio_proc: module loaded and /proc/gpio/ created
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb1100003 (irq = 37) is a 16550A
serial8250 serial8250.0: unable to register port at index 0 (IO3f8 MEM0 IRQ4): -28
serial8250 serial8250.0: unable to register port at index 1 (IO2f8 MEM0 IRQ3): -28
serial8250 serial8250.0: unable to register port at index 2 (IO3e8 MEM0 IRQ4): -28
serial8250 serial8250.0: unable to register port at index 3 (IO2e8 MEM0 IRQ3): -28
Infineon ADM6996: Registered new driver
Marvell 88E6060: Registered new driver
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
scanning for root partition
[0x00000000]
[0x00010000]
[0x00020000]
[0x00030000]
[0x00040000]
[0x00050000]
[0x00060000]
[0x00070000]
[0x00080000]
[0x00090000]
[0x000A0000]
[0x000B0000]
[0x000C0000]
[0x000D0000]
[0x000E0000]
[0x000F0000]
[0x00100000]
found squashfs at 100000
found RedBoot partition at [0xBFC00000]
found linux partition at [0xBFC30000]
Creating 8 MTD partitions on "spiflash":
0x00000000-0x00030000 : "RedBoot"
0x00030000-0x003d0000 : "linux"
0x00100000-0x003b0000 : "rootfs"
0x003b0000-0x003d0000 : "ddwrt"
0x003d0000-0x003e0000 : "nvram"
0x003e0000-0x003f0000 : "FIS Directory"
0x003f0000-0x00400000 : "board_config"
0x00030000-0x003e0000 : "fullflash"
watchdog hb: 20 ISR: 0x20 IMR: 0x8 WD : 0x18cca547 WDC: 0x0
ar2315_wdt_init using heartbeat 20 s cycles 800000000
watchdog hb: 20 ISR: 0x20 IMR: 0x88 WD : 0x2fa9dfc8 WDC: 0x0
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <deri@ntop.org>
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
decode /dev/mtdblock2
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 124k freed
ar2315_wdt: starting watchdog w/timeout 20 seconds
watchdog hb: 20 ISR: 0x20 IMR: 0x89 WD : 0x2fad08b4 WDC: 0x0
Algorithmics/MIPS FPU Emulator v1.5
test pattern is FFFFFFFF
eth0: Atheros AR231x: 00:24:01:b7:e9:4a, irq 4
ar2313_eth_mii: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:00)
ath_hal: module license 'Proprietary' taints kernel.
Reset ICPLUS Phy
Start Autonegotiation
Port 0, Negogiation timeout
Port 1, Negogiation timeout
Port 2, Negogiation timeout
Port 3, Negogiation timeout
Port 4, Negogiation timeout
Port 5, Negogiation timeout
Setup VLANS
sh: cannot create /proc/sys/net/ipv4/tcp_westwood: nonexistent directory
sh: cannot create /proc/sys/net/ipv4/tcp_vegas_cong_avoid: nonexistent directory
sh: cannot create /proc/sys/net/ipv4/tcp_vegas_alpha: nonexistent directory
sh: cannot create /proc/sys/net/ipv4/tcp_vegas_beta: nonexistent directory
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device vlan0 entered promiscuous mode
device eth0 entered promiscuous mode
sh: cannot create /proc/sys/dev/wifi0/compression: nonexistent directory
ath0
Interface doesn't accept private ioctl...
compression (8BE0): Invalid argument
Interface doesn't accept private ioctl...
ff (8BE0): Invalid argument
Invalid command : scandisable
Interface doesn't accept private ioctl...
compression (8BE0): Invalid argument
Interface doesn't accept private ioctl...
ff (8BE0): Invalid argument
SET failed on device ath0 ; Invalid argument.
Interface doesn't accept private ioctl...
compression (8BE0): Invalid argument
Interface doesn't accept private ioctl...
ff (8BE0): Invalid argument
device ath0 entered promiscuous mode
Invalid command : scandisable
br0: port 2(ath0) entering learning state
br0: port 1(vlan0) entering learning state
br0: topology change detected, propagating
br0: port 2(ath0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan0) entering forwarding state
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
CPU 0 Unable to handle kernel paging request at virtual address 2bfd1b16, epc == c00d8120, ra == c00da4fc
Oops[#1]:
Cpu 0
$ 0 : 00000000 10009400 0000ffff 2bfd1b12
$ 4 : 0000ffff c0107c40 00000000 00280400
$ 8 : 00000024 00000002 00000002 82848b96
$12 : 00000018 00000016 6ffffffa 70000013
$16 : 80a22c46 8092d3a0 80c9c3a0 8092a000
$20 : 8092db58 8092a1cf 00000000 00016826
$24 : 00000002 00000000
$28 : 80f54000 80f55b40 c0110000 c00da4fc
Hi : 00000000
Lo : 00000000
epc : c00d8120 Tainted: P
ra : c00da4fc Status: 10009403 KERNEL EXL IE
Cause : 30800008
BadVA : 2bfd1b16
PrId : 00019064
Modules linked in: ath_ahb ath_hal(P) ar2313
Process rmmod (pid: 218, threadinfo=80f54000, task=80ecd0a8)
Stack : 00000001 80095c88 80a22c36 8092d3a0 c00da4fc 8092db58 c00f7338 00000001
80331660 80ecd0a8 8092a000 8092db58 8097ebe0 8092d3a0 80c9c3a0 80934000
c00da860 c00da844 802e0000 00000001 00b33717 800a3a84 80a22c28 80c9c3a0
8092d3a0 80c9c3a0 8092a000 80998800 00000000 c00c5738 80ed5c50 80ecd0a8
802b8860 2aab0000 80f55ca8 00030000 80ed5c50 80ecd0a8 8004e2cc 8004e29c
...
Call Trace:[<80095c88>][<c00da4fc>][<c00f7338>][<c00da860>][<c00da844>][<800a3a84>][<c00c5738>][<802b8860>][<8004e2cc>][<8004e29c>][<802b8860>][<c00d21cc>][<802b8860>][<8004e29c>][<802b8860>][<8008b604>][<80043140>][<8008d6fc>][<80042a40>][<8008e2a0>][<80043164>][<802b8860>][<80095c88>][<8004ec48>][<800a1650>][<800a1634>][<800a6d34>][<800a3980>][<802b8860>][<802b8860>][<802b8860>][<802b8894>][<8004e29c>][<802b8860>][<802b8860>][<800a92d8>][<802b8860>][<800a7c34>][<800b053c>][<80048820>][<800b3c84>][<80043140>][<8004c0d0>]
Code: 3402ffff 10620002 3404ffff <90640004> 8fbf0010 00801021 03e00008 27bd0018 3c02c00f
Kernel panic - not syncing: Fatal exception in interrupt
Rebooting in 1 seconds..
Fragen soweit beantwortet.
Leider kann ich kein strg+c drücken um in den bootmanager zu kommen.
Also ein letztes Mal brauche ich eure Hilfe. :(
Ok, habe das Problem ganz leicht geloest.
Ich hatte als redboot ip und serverip die selbe dummerweise vergeben, darum konnte ich nicht mehr mit telnet zu redboot connecten.
Durch die serielle console habe ich dann bemerkt dass ich redboot durch dhcp ips zuweisen kann.
Neue ip und siehe da, telnet ging wieder.
Ddwrt andere version drauf geflashed und alles geht jetzt.
Sehr komisch war die tatsache dass ich bei allen ausser der vorletzten beta einen kernel panic hatte... sogar bei der letzten stable.
Schade eigentlich.
