Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Wed Nov 15, 2006 0:29 Post subject:
i will write a comment like *solved* to the post so far i implemented the card _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
I'm trying to install the X86 version on a nokia ip130. It seems to work, only it gives a failure with loading the 3 intel e100 ethernet interfaces:
==========
PCI: Found IRQ 10 for device 0000:00:0e.0
IRQ routing conflict for 0000:00:0e.0, have irq 11, want irq 10
e100: 0000:00:0e.0: e100_eeprom_load: EEPROM corrupted (stored: e6bc,
calc'ed: 54cf)
e100: eth0: e100_probe: addr 0x80100000, irq 11, MAC addr 00:A0:8E:22:xx:xx
PCI: Found IRQ 11 for device 0000:00:0f.0
IRQ routing conflict for 0000:00:0f.0, have irq 10, want irq 11
e100: 0000:00:0f.0: e100_eeprom_load: EEPROM corrupted (stored: d9cc,
calc'ed: 53cf)
e100: eth1: e100_probe: addr 0x80300000, irq 10, MAC addr 00:A0:8E:22:xx:xx
PCI: Found IRQ 10 for device 0000:00:10.0
IRQ routing conflict for 0000:00:10.0, have irq 5, want irq 10
e100: 0000:00:10.0: e100_eeprom_load: EEPROM corrupted (stored: d95a,
calc'ed: 52cf)
e100: eth2: e100_probe: addr 0x80500000, irq 5, MAC addr 00:A0:8E:22:xx:xx
==========
I've tryed on 3 ip130's, but all gave the same error.
I've searched with google and found that many different brands using the intel e100 and that many of these are giving problems with kernel 2.6
The solution should be patching it.
Mayby this gives some more info: http://lkml.org/lkml/2006/7/9/55
==========
DD-WRT VeryBusyBox v1.2.2 (2006.11.15-04:25+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
~ # lspci
00:00.0 Host briCyrix Corporation PCI Master
00:0d.0 Co-processor: Broadcom Corporation: Unknown device 5802 (rev 01)
00:0e.0 Ethernet controller: Intel Corporation 8255xER/82551IT Fast Ethernet Controller (rev 10)
00:0f.0 Ethernet controller: Intel Corporation 8255xER/82551IT Fast Ethernet Controller (rev 10)
00:10.0 Ethernet controller: Intel Corporation 8255xER/82551IT Fast Ethernet Controller (rev 10)
00:12.0 ISA bridge: Cyrix Corporation 5530 Legacy [Kahlua] (rev 30)
00:12.1 Bridge: Cyrix Corporation 5530 SMI [Kahlua]
00:12.2 IDE interface: Cyrix Corporation 5530 IDE [Kahlua]
00:12.3 Multimedia audio controller: Cyrix Corporation 5530 Audio [Kahlua]
~ #
==========
Is it possible to solve this problem? I think more people can get this problem, because the intel e100 is many used nic.
I'm ready to help/test with this problem.
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Wed Nov 22, 2006 14:59 Post subject:
the e100 works perfectly. but you have another problem which is caused by your bios or something else. the irq mapping in your computer looks like faulty. this can be a acpi problem _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Mon Nov 27, 2006 13:36 Post subject:
i fixed it now by adding this driver to the detection list. never knewed that there is a second pro 100 driver _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Hi all, I stumbled into this x86 version of DD-WRT, because of this I started digging. And ran into some of my older router systems which I still had doing nothing (for 4+ years i think).
This Digital Multia (pizabox systems) (socket5 system @133Mhz).
I put (for now) 32Megs of ram in the box, 1 old ~800Meg 2.5Inch HDD (yeah,4200RPM but it still works after all those years!).
Managed to get the DDWRT x86 on it , and I was able to boot it. On the console.
The onboard nic is not detected, same for the PCMCIA slots (2) in this machine.
I managed to get one 3com board working, and I was able to log in via the network. (3c905 still rox )
The onboard card, DEC21040 (quite comon, works under almost every linux distri)
The lspci I extracted on this system:
00:00.0 Host bridge: Intel Corporation 430FX - 82437FX TSC [Triton I] (rev 01)
00:06.0 Non-VGA unclassified device: LSI Logic / Symbios Logic 53c810 (rev 01)
00:07.0 ISA bridge: Intel Corporation 82371FB PIIX ISA [Triton I] (rev 02)
00:07.1 IDE interface: Intel Corporation 82371FB PIIX IDE [Triton I] (rev 02)
00:08.0 Ethernet controller: Digital Equipment Corporation DECchip 21040 [Tulip] (rev 23)
00:0b.0 VGA compatible controller: S3 Inc. 86c968 [Vision 968 VRAM] rev 0
00:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
Next I will try the Soekris 4521 and see what this will do...
only atheros wireless NICS work with dd-wrt x86 , this has to do with the poor driver support for most other wireless chipsets , in your case texas instruments ...
Console screen get errors like this A LOT!
SIOCGIFFLAGS: No Such Device (over and over while booting...)
CPU is CPU
CPU Model - VIA Samuel 2
CPU Clock - 796.180 MHz
It is a PCChips M789CG which I use for all of my experiments. Runs ddwrt-x86-reg perfectly. I am anxious to see how well it runs in production with ddwrt-x86-reg.
I have no No eth2. Is all the above basically telling me my Senao NL2511MP is not compatible? Not Atheros? Is this fixable? Do I need to supply more info? Do I need to get a new wifi card?
Richard