Getnet GR-124W Rev. 1.0 supported by DD-WRT?

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware
Author Message
darkside40
DD-WRT Novice


Joined: 02 Mar 2007
Posts: 25

PostPosted: Sat Jun 26, 2010 20:26    Post subject: Getnet GR-124W Rev. 1.0 supported by DD-WRT? Reply with quote
Hi there,
i just bought an ultra low cost (16€) Wireless Router which is running Linux, and now i wanted to now if it could be supported bei DD-WRT.

The Router is a Getnet GR-124W, seems that Getnet belongs to Edimax and build cheap devices for them.

You can find the Product here incl. Links to an Linux SDK: http://www.getnet.eu/products_GR-124W.html

Here are the Specs of the Router:
CPU: Ralink 3050F / 384MHz
Flash: 4MB / KH29LV320DB
Ram: 16MB / Aotom A128168L-6TE
Wlan: 54MBit
Lan: 4x 100MBit
Serial Port: Yes (i will mark the Pinout if needed)
JTAG: 14 Pin Connector is there but i dont know the Pinout and the diy JTAG cable is crap
FCC: No ID

Serial Output:
Code:
U-Boot 1.1.3 (Oct 23 2009 - 11:47:45)


Board: Ralink APSoC DRAM:  16 MB

relocate_code Pointer at: 80fb0000

flash_protect ON: from 0xBF000000 to 0xBF01D733

flash_protect ON: from 0xBF030000 to 0xBF030FFF

*** Warning - bad CRC, using default environment


============================================

Ralink UBoot Version: 3.3

--------------------------------------------

ASIC 3052_MP2 (Port5<->None)

DRAM component: 128 Mbits SDR

DRAM bus: 16 bit

Total memory: 16 MBytes

Flash component: NOR Flash

Date:Oct 23 2009  Time:11:47:45

============================================

icache: sets:256, ways:4, linesz:32 ,total:32768

dcache: sets:128, ways:4, linesz:32 ,total:16384


 ##### The CPU freq = 384 MHZ ####


SDRAM bus set to 16 bit

 SDRAM size =16 Mbytes


Please choose the operation:

   1: Load system code to SDRAM via TFTP.

   2: Load system code then write to Flash via TFTP.

   3: Boot system code via Flash (default).

   4: Entr boot command line interface.

   6: Load whole flash then write to Flash via TFTP.

   9: Load Boot Loader code then write to Flash via TFTP.



You choosed 3


 0

   

3: System Boot system code via Flash.

## Booting image at bf050000 ...

   Image Name:   Linux Kernel Image

   Created:      2009-12-23   1:12:24 UTC

   Image Type:   MIPS Linux Kernel Image (lzma compressed)

   Data Size:    3449550 Bytes =  3.3 MB

   Load Address: 80000000

   Entry Point:  80233000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

No initrd

## Transferring control to Linux (at address 80233000) ...

## Giving linux memsize in MB, 16


Starting kernel ...



LINUX started...

 THIS IS ASIC
Linux version 2.6.21 (fupeng@wireless.gj.com) (gcc version 3.4.2) #1 Mon Nov 16 14:34:38 CST 2009

 The CPU feqenuce set to 384 MHz
CPU revision is: 0001964c
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 4064
Kernel command line: console=ttyS1,57600n8 root=1f04
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 90800064, status = 1100ff00
PID hash table entries: 64 (order: 6, 256 bytes)
calculating r4koff... 00177000(1536000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13776k/16384k available (1976k kernel code, 2608k reserved, 271k data, 116k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered (default)
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
rdm_major = 254
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
ralink flash device: 0x1000000 at 0x1f000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
0x00040000-0x00050000 : "Factory"
0x00050000-0x0010730e : "Kernel"
mtd: partition "Kernel" doesn't end on an erase block -- force read-only
0x0010730e-0x01000000 : "RootFS"
mtd: partition "RootFS" extends beyond the end of device "Ralink SoC physically mapped flash" -- size truncated to 0x2f8cf2
mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
0x00050000-0x01000000 : "Kernel_RootFS"
mtd: partition "Kernel_RootFS" extends beyond the end of device "Ralink SoC physically mapped flash" -- size truncated to 0x3b0000
block2mtd: version $Revision: 1.1.1.1 $
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (128 buckets, 1024 max) - 228 bytes per conntrack
ip_conntrack_pptp version 3.1 loaded
ip_nat_pptp version 3.0 loaded
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.00  256 rx/tx descriptors allocated, mtu = 1500!
GDMA1_MAC_ADRH -- : 0x0000001f
GDMA1_MAC_ADRL -- : 0x1f978d80
PROC INIT OK!
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 116k freed

init started: BusyBox v1.12.1 (2009-12-12 09:41:58 CST)

starting pid 12, tty '': '/etc_ro/rcS'
Algorithmics/MIPS FPU Emulator v1.5
mount: mounting devpts: called with bogus options
none on /sys failed: No such device
mount: mounting none on /proc/bus/usb failed: No such file or directory
mount: mounting tmpfs on /var/webcgi failed: Invalid argument
internet.sh
MP AUTOMATION daemon (ver 1.0)

starting pid 39, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2009-12-12 09:41:58 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# Password for 'admin' changed
insmod: bridge.ko: module not found
insmod: mii.ko: module not found
insmod: raeth.ko: module not found

phy_tx_ring = 0x00f54000, tx_ring = 0xa0f54000

phy_rx_ring = 0x00000000, rx_ring = 0x00000000
RT305x_ESW: Link Status Changed
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 710000
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
rmmod: rt2860v2_ap: No such file or directory
rmmod: rt2860v2_sta: No such file or directory
Commit crc = c4a2524a
RT305x_ESW: Link Status Changed
rt2860v2_ap: module license 'unspecified' taints kernel.


=== pAd = c0002000, size = 495376 ===

<-- RTMPAllocAdapterBlock, Status=0
rmmod: ip_nat_pptp: No such file or directory
rmmod: ip_conntrack_pptp: No such file or directory
RX DESC a0a06000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 0
2. Phy Mode = 0
3. Phy Mode = 0
MCS Set = 00 00 00 00 00
Main bssid = 00:1f:1f:97:8d:80
<==== rt28xx_init, Status=0
0x1300 = 00064380
insmod: 8021q.ko: module not found
eth2.2: Setting MAC address to  00 1f 1f 97 8d 80.
VLAN (eth2.2):  Underlying device (eth2) has same MAC, not checking promiscious mode.
ifconfig: ioctl 0x8913 failed: No such device
brctl: bridge br0: No such device or address
##### config RT3052 vlan partition (WLLLL) #####
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=54, value=4003
switch reg write offset=58, value=6005
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1002
switch reg write offset=44, value=4003
switch reg write offset=48, value=6005
switch reg write offset=70, value=48444142
switch reg write offset=74, value=ffffff50
device ra0 entered promiscuous mode
brctl: bridge br0: Device or resource busy
RT305x_ESW: Link Status Changed
eth2.1: dev_set_promiscuity(master, 1)
device eth2 entered promiscuous mode
device eth2.1 entered promiscuous mode
eth2.3: dev_set_promiscuity(master, 1)
device eth2.3 entered promiscuous mode
eth2.4: dev_set_promiscuity(master, 1)
device eth2.4 entered promiscuous mode
eth2.5: dev_set_promiscuity(master, 1)
device eth2.5 entered promiscuous mode
udhcpc (v1.12.1) started
br0: port 5(eth2.5) entering learning state
br0: port 4(eth2.4) entering learning state
br0: port 3(eth2.3) entering learning state
br0: port 2(eth2.1) entering learning state
br0: port 1(ra0) entering learning state
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
/sbin/lan.sh: line 63: hostname: not found
killall: udhcpd: no process killed
RT305x_ESW: Link Status Changed
Set: phy[1].reg[0] = 3900
Set: phy[2].reg[0] = 3900
RT305x_ESW: Link Status Changed
Set: phy[3].reg[0] = 3900
Set: phy[4].reg[0] = 3900
Set: phy[1].reg[0] = 3100
Set: phy[2].reg[0] = 3100
Set: phy[3].reg[0] = 3100
RT305x_ESW: Link Status Changed
Set: phy[4].reg[0] = 3100
ifconfig: ioctl 0x8913 failed: No such device
/sbin/lan.sh: line 148: can't create /proc/sys/net/ipv6/conf/all/forwarding: nonexistent directory
killall rt2860apd 1>/dev/null 2>&1
iptables -F -t filter 1>/dev/null 2>&1
iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -F macipport_filter 1>/dev/null 2>&1
iptables -D FORWARD -j web_filter  1>/dev/null 2>&1
iptables -F web_filter  1>/dev/null 2>&1
iptables -P INPUT ACCEPT
iptables -P OUTPUT ACCEPT
iptables -P FORWARD ACCEPT
iptables -t filter -N web_filter 1>/dev/null 2>&1
iptables -t filter -N macipport_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1
iptables -t filter -A INPUT -i eth2.2 -p icmp -j DROP
iptables -A INPUT -i eth2.2 -m state -p tcp --dport 80 --state NEW,INVALID -j DROP
iptables -A INPUT -i ! eth2.2 -j ACCEPT
iptables -A INPUT -i eth2.2 -m state --state RELATED,ESTABLISHED -j ACCEPT
iptables -A INPUT -j DROP
iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1
iptables -t nat -F port_forward  1>/dev/null 2>&1; iptables -t nat -X port_forward  1>/dev/null 2>&1
iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1
iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ  1>/dev/null 2>&1
iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1
iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j DMZ 1>/dev/null 2>&1
iptables -t nat -F POSTROUTING
nat.sh
ntp.sh
greenap.sh init
sh: greenap.sh: not found
ddns.sh
route delete 239.255.255.250 1>/dev/null 2>&1
killall wscd 1>/dev/null 2>&1
killall -9 wscd 1>/dev/null 2>&1
iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
killall -q klogd
killall -q syslogd
syslogd -C8 1>/dev/null 2>&1
klogd 1>/dev/null 2>&1
killall -q zebra
killall -q ripd
/bin/qos_run
webs: Listening for HTTP requests at address 192.168.1.1
br0: topology change detected, propagating
br0: port 5(eth2.5) entering forwarding state
br0: topology change detected, propagating
br0: port 4(eth2.4) entering forwarding state
br0: topology change detected, propagating
br0: port 3(eth2.3) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth2.1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(ra0) entering forwarding state


So you see it runs a Linux Kernel 2.6.21, and the output says Asic 3052_MP2, the Chip itself is labeled 3050F.
Here are two HiRes Pics of the PCB, if you need any more simply tell me.
Sponsor
darkside40
DD-WRT Novice


Joined: 02 Mar 2007
Posts: 25

PostPosted: Tue Jun 29, 2010 12:10    Post subject: Reply with quote
No one an idea?
Or not interested?
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7018

PostPosted: Tue Jun 29, 2010 13:13    Post subject: Reply with quote
No dd-wrt builds for 16MB ram Ralink devices yet, and possibly never.
It is just too little for a standard dd-wrt build to work in.
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17339
Location: Hesse/Germany

PostPosted: Tue Jun 29, 2010 13:40    Post subject: Reply with quote
no we have 1 ralink unit with 16mb but stability is far from perfect. but without an donation it wont be possible on this low ram units.
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
_________________
Andreas Baumert: "Kundige Menschen befragen Fachleute, ohne ihnen auf die Nerven zu gehen. Sie stellen keine Fragen, die sie mit etwas Fleiß und Lektüre selber beantworten können. Sie wissen, auf welche Quellen es ankommt,und wie man sich Zugang zu ihnen verschafft."
darkside40
DD-WRT Novice


Joined: 02 Mar 2007
Posts: 25

PostPosted: Mon Nov 22, 2010 10:49    Post subject: Reply with quote
Maybe there is any beta firmware i could try to flash in the meantime?
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17339
Location: Hesse/Germany

PostPosted: Mon Nov 22, 2010 13:55    Post subject: Reply with quote
no port without donated hw
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
_________________
Andreas Baumert: "Kundige Menschen befragen Fachleute, ohne ihnen auf die Nerven zu gehen. Sie stellen keine Fragen, die sie mit etwas Fleiß und Lektüre selber beantworten können. Sie wissen, auf welche Quellen es ankommt,und wie man sich Zugang zu ihnen verschafft."
chateau
DD-WRT User


Joined: 20 Aug 2010
Posts: 104

PostPosted: Mon Nov 22, 2010 15:05    Post subject: Reply with quote
Quote:
no we have 1 ralink unit with 16mb but stability is far from perfect


My ESR-9753 which is 16mb seems to run OK on the ESR-9752 DD-WRT firmware.

I have used it for an AP in the past and it is now being used as a Bridged Repeater by a relative.

It has never been subjected to heavy traffic in any of these applications. Not sure if that has any bearing on stability.
darkside40
DD-WRT Novice


Joined: 02 Mar 2007
Posts: 25

PostPosted: Mon Nov 22, 2010 16:03    Post subject: Reply with quote
May you have a photo of the ESR-9753 PCB?
sfstudio
DD-WRT User


Joined: 19 Sep 2010
Posts: 218

PostPosted: Mon Nov 22, 2010 17:38    Post subject: Re: Getnet GR-124W Rev. 1.0 supported by DD-WRT? Reply with quote
darkside40 wrote:

Flash: 4MB / KH29LV320DB
Ram: 16MB / Aotom A128168L-6TE


You should try Wive-RTNL build for acorp 1T1R.
Update from boot menu (or try update over web).
Download http://sourceforge.net/projects/wive-ng/files/wive-ng-rtnl/.

Unzip and try acorp.1T1R-16.1.2.3.RU.18112010.bin.zip
chateau
DD-WRT User


Joined: 20 Aug 2010
Posts: 104

PostPosted: Mon Nov 22, 2010 17:54    Post subject: Reply with quote
Quote:
May you have a photo of the ESR-9753 PCB?


It looks nothing like your router so I don't think you could safely try that firmware.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum