bbota DD-WRT Novice
Joined: 04 Mar 2011 Posts: 2
|
Posted: Fri Mar 04, 2011 2:40 Post subject: WLI-TX4-G54HP MAC Address conflict |
|
Hello,
Have been trying to set two Buffalo WLI-TX4-G54HP as APs over the same LAN segment, to allow roaming access to WiFi clients. Both APs were just flashed with recommended v24-sp2 (08/07/10) std. Each AP works independently without troubles, and clients can connect to any of them with the same security settings.
As soon as I connect the second AP to the network, sluggish behavior starts. Only one of the APs respond to pings, and the one that answers, gives indication the other is unreachable. Found both APs show the same MAC Address 00:0d:0b:91:00:00. Tried assigning a MAC using MAC Clone, but nothing changes.
In case it helps here is the interface information, using a script published in a previous post:
root@AP250:~# ifconfig
brctl show br0
routebr0 Link encap:Ethernet HWaddr 00:0D:0B:91:00:00
inet addr:192.168.39.250 Bcast:192.168.39.255 Mask:255.255.255.0
UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
RX packets:7034 errors:0 dropped:0 overruns:0 frame:0
TX packets:6856 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:813098 (794.0 KiB) TX bytes:6260439 (5.9 MiB)
br0:0 Link encap:Ethernet HWaddr 00:0D:0B:91:00:00
inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
eth0 Link encap:Ethernet HWaddr 00:0D:0B:91:00:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:6571 errors:0 dropped:0 overruns:0 frame:0
TX packets:7239 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:861308 (841.1 KiB) TX bytes:6360730 (6.0 MiB)
Interrupt:4
eth1 Link encap:Ethernet HWaddr 00:0D:0B:AF:AB:E1
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:390 errors:0 dropped:0 overruns:0 frame:117876
TX packets:1533 errors:32 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:67513 (65.9 KiB) TX bytes:387564 (378.4 KiB)
Interrupt:2 Base address:0x5000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@AP250:~# nvram show|grep ifn
wl0_ifname=eth1
wan_ifname2=eth2
pppoe_wan_ifname=eth2
pppd_pppifname=
lan_ifnames=eth0 eth1
pppoe_ifname=eth2
wan_ifnames=eth2
lan_ifname=br0
wl_ifname=
size: 19841 bytes (12927 left)
wan_ifname=eth2
root@AP250:~# brctl show br0
bridge name bridge id STP enabled interfaces
br0 8000.000d0b910000 no eth0
eth1
root@AP250:~# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.39.0 * 255.255.255.0 U 0 0 0 br0
169.254.0.0 * 255.255.0.0 U 0 0 0 br0
127.0.0.0 * 255.0.0.0 U 0 0 0 lo
default 192.168.39.254 0.0.0.0 UG 0 0 0 br0
Any suggestion would be greatly appreciated.
BB |
|