Flashing EAP 9550

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Senao Devices
Goto page 1, 2  Next
Author Message
guaguasi
DD-WRT Novice


Joined: 09 Mar 2011
Posts: 2

PostPosted: Wed Mar 09, 2011 10:41    Post subject: Flashing EAP 9550 Reply with quote
EnGenius EAP9550
HW: v.1.0.0
SW: v.1.1.3
FCC ID: U2M-AP9550

Firmware found: http://www.dd-wrt.com/site/support/other-downloads?path=others/eko/BrainSlayer-V24-preSP2/2011/02-17-11-r16214/Senao-EAP9550/ (no instructions)

I have read quite a few posts and tried different things. At first, I tried the sticky for all devices and I could not get into RedBoot. After some searching, I decided to try the other sticky for only EOC-2610. Lo and behold, that got me to the next step.

Given that the method I used does not seem to be the norm, I'm curious as to how I should proceed so as to not brick my device. I'm not sure if continuing with the back door method described in the 2610 wiki and it not working would cripple the device. I'm lead to believe that it is unrecoverable.

When I do actually log in to the device, I am left with a menu and a barely responsive putty session (as seen below, the 'n's appear by themselves once every 3 seconds). I read in a post about a 9500, I believe, that the bootloader needed to be updated. I am not sure if that is accurate or if that applies to my device as well, but if it does, I don't have a serial cable so my quest ends there.

I would appreciate any help given.
Sponsor
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17480
Location: Hesse/Germany

PostPosted: Wed Mar 09, 2011 11:19    Post subject: Reply with quote
read 1st:
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
guaguasi
DD-WRT Novice


Joined: 09 Mar 2011
Posts: 2

PostPosted: Wed Mar 09, 2011 12:34    Post subject: Reply with quote
Here's the thing. As helpful as your response was, I made this post because, after reading the guidelines and as per the guidelines, my "problem still exist."

Perhaps I may have missed something, and, if so, would you be so kind as to point out my folly. Otherwise, I'd still appreciate some assistance.
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17480
Location: Hesse/Germany

PostPosted: Wed Mar 09, 2011 13:17    Post subject: Reply with quote
u dont even know your chipset
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
mrchew1982
DD-WRT Novice


Joined: 13 Mar 2011
Posts: 2

PostPosted: Sun Mar 13, 2011 2:15    Post subject: a little help... Reply with quote
my google-fu turned me onto:
http://www.dd-wrt.com/dd-wrtv2/down.php?path=downloads%2Fothers%2Feko%2FBrainSlayer-V24-preSP2%2F2011%2F02-17-11-r16214%2FSenao-EAP9550/

i just searched for "EAP9550 ddwrt" (without the quotes).

looks like someone (probably brainslayer, bless his soul) posted a webflash, that might be usable from their web UI.

I hope that's helpful, I don't know much about the device. I'm still doing research and leaning towards the 3660. I find it hard to believe that they advertise speeds up 300Mbps but only have a 100Mbps LAN connection on the device. Unless i'm not understanding something, seems like 100Mbps is the hard limit, which is the same as the 3660, and the 3660 has more x-mit power.
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1191

PostPosted: Thu Jun 16, 2011 2:11    Post subject: EAP-9550- Reply with quote
ok so here it goes:

I think when I got my first device it had verison 1.1.3 stock senao firmware. I think I was able to get it to flash via tftp uploading firmware.bin. Since then I have gotten a few more of these devices and have not been able to flash them.

1st thing: there is no redboot port on 9000
2nd: no emergency room
3rd: webui is requesting .dlf files, so neither .bin work.... changing file name fails the upload.
4th.. tryed telneting into the device and using the webupg ftp to a local ftp server on my pc... no go.
5th.. Tried rename firmware.bin to firmware.ram and seting up tftp server... no go...
6th.. I have tried upgrading to 1.2.2 and also down to 1.1.3 and nothing flashes to dd-wrt..

I am out of ideas or think I have exhausted the last 2 hours and got nowhere. There is no offical documentation of howto properly flash this device and it has been support since feb 2011 in dd-wrt downloads section... The Chipset is RALINK and after check .dlf files are belkin encrypted files and the stock webui requires these files to upgrade it.

so in closing how do you get this to flash?

Fractal.
GeeTek
DD-WRT Guru


Joined: 06 Jun 2006
Posts: 3742
Location: I'm the one on the plate.

PostPosted: Thu Jun 16, 2011 3:36    Post subject: Reply with quote
Ubiquity has recently changed their hardware to facilitate improved regulation compliance. With Senao being the stuttering, red-headed bastard half step cousing of Ubiquity, it is not inconceivable that they too have had to make some revisions.
_________________
http://69.175.13.131:8015 Streaming Week-End Disco. Station Ripper V 1.1 will do.
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1191

PostPosted: Thu Jun 16, 2011 3:44    Post subject: Reply with quote
yeah something is definatly going that way lol.... I never have any problems with broadcom, and it always works.... once you start stepping out the box and go for looks (aka smoke detector ) it gets complicated and doesnt work 80% of the time..

PS: I tried the bootloader install method as well, no dice there either... get arp packets but it doesnt install bootloader either... I dont think this device is suppose to have a redboot.

Fractal


GeeTek wrote:
Ubiquity has recently changed their hardware to facilitate improved regulation compliance. With Senao being the stuttering, red-headed bastard half step cousing of Ubiquity, it is not inconceivable that they too have had to make some revisions.
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17480
Location: Hesse/Germany

PostPosted: Thu Jun 16, 2011 7:39    Post subject: Reply with quote
http://www.dd-wrt.com/wiki/index.php/WHR-G300N
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1191

PostPosted: Thu Jun 16, 2011 17:40    Post subject: Reply with quote
I tried the TFTPd32 method, seems the device does not have a bootloader at 192.168.11.1

The device never tries to connect to 192.168.11.2 during startup or after 30/30/reset ect.

I also tried installing bootloader from the forums method and no go.

The device pings @ 192.168.1.1 right from power on, tftp and telnet methods to upgrade firmware fail.. The webui looks for .dlf files to upgrade its software. Senao firmware come in 2 files, 1 is the kernel, and the other is the apps... Not sure what to try next, I think we have to get a bin that will pass encrytion for .dlf files and flash from webui.

Fractal



Sash wrote:
http://www.dd-wrt.com/wiki/index.php/WHR-G300N
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1191

PostPosted: Thu Jun 16, 2011 19:19    Post subject: EAP-9550 Reply with quote
ok,

So I decide to call engenius technologies to see if this device has a redboot port or special IP ect that would allow dd-wrt to be written to it. I was on hold for well over and hour and was then able to communicate with there tech "Marcos" Here is the summary of what I was told.

1. Only the EAP-3660 is supported by dd-wrt, the 9550 is not supported.
2. The .dlf files are encrypted WEBUI flash files only and there is no opensource for this router.
3. There are no future plans of releasing source or encryption headers to the community going forward with their products. There products are going to remain closed source... And if you are able to get dd-wrt on the device successfully then you voice the warrenty ect.

In a nutshell he said that engenious took alot of RMA's cause people bricked there router trying to get dd-wrt installed, so an executive decision was made to close source all new products.

so to get this working someone is officially going to have to DUMP the cfe, find the encryption method for webui or alternate redboot. I am doubtful at this point anyone has gotten dd-wrt to work with newer model EAP-9550's. Back to the shelf it goes until I solder a serial up and decide if its worth dumping the cfe.

Fractal.

Incase anyone wants there contact info and doesnt know how to use google.

Corporate Mailing Address:
1580 Scenic Ave.
Costa Mesa, CA 92626
Electronic Mail:
Telecom: info@engeniustech.com
Datacom: wlan@engeniustech.com
Website: partners@engeniustech.com

Contact by Telephone:
Toll-free: 888-735-7888
Local: 714-432-8668
Fax: 714-432-8667

Accounts Payable ext. 518
Credits ext. 856
Telecom Sales ext. 515
Telecom Support ext. 514
Datacom Sales ext. 516
Datacom Support ext. 517
Consumer Data Sales ext. 518
Consumer Data Support ext. 519
ascott
DD-WRT Novice


Joined: 17 Jun 2011
Posts: 11

PostPosted: Fri Jun 17, 2011 21:13    Post subject: Reply with quote
Here's some serial output. (Not much interesting.)

No help nor any commands available.

Code:
U-boot Ver:1.0.1.30 2009/10/12


Board: Ralink APSoC DRAM:  32 MB  1*32 MB
============================================
ASIC 3052_MP2 (Port5<->None)
Product Name: EAP9550
SDRAM CAS = 3(d1835272)
============================================

Please choose the operation:
   1: Load system code to SDRAM via TFTP.

LINUX started...

 THIS IS ASIC
init started: BusyBox v1.7.5 (2010-10-13 13:42:00 CST)
starting pid 131, tty '/dev/console': '/sbin/config_init'
Config Init version: 1.2.2.17 date: 2010/10/13
Could not find Watchdog driver (/apps/lib/modules/2.6.21/kernel/arch/mips/rt2880/rt_timer.ko)
starting pid 178, tty '/dev/ttyS1': '/sbin/config_term'
************************************************************************
*                                  EAP9550                             *
************************************************************************

KernelApp/Ramdisk Ver:1.2.2.17                   Date:2010/10/13
console> cat: can't open '/apps/lib/modules/2.6.21/modulesApp.dep': No such file or directory
ln: /sbin/./apps_init: File exists
ln: /sbin/./httpsd: File exists
sh: cannot create /proc/senao/ip_conntrack_interface: nonexistent directory
sh: cannot create /proc/senao/ip_conntrack_interface: nonexistent directory
sh: cannot create /proc/senao/ip_conntrack_interface: nonexistent directory
sh: cannot create /proc/switch/power_status: nonexistent directory
sh: cannot create /proc/switch/power_status: nonexistent directory

?
************************************************************************
*                                  EAP9550                             *
************************************************************************

KernelApp/Ramdisk Ver:1.2.2.17                   Date:2010/10/13
console> j^H
************************************************************************
*                                  EAP9550                             *
************************************************************************

KernelApp/Ramdisk Ver:1.2.2.17                   Date:2010/10/13
console> help
************************************************************************
*                                  EAP9550                             *
************************************************************************


If I choose 1. at startup, it appears I can tftp an image over that way.

Code:
U-boot Ver:1.0.1.30 2009/10/12


Board: Ralink APSoC DRAM:  32 MB  1*32 MB
============================================
ASIC 3052_MP2 (Port5<->None)
Product Name: EAP9550
SDRAM CAS = 3(d1835272)
============================================

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   
1: System Load Linux to SDRAM via TFTP.
 Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.99.9) ==:     


It appears as though it defaults to looking to 192.168.99.9 for an image. But which image? A .bin, or does it have to be a .dlf?
ascott
DD-WRT Novice


Joined: 17 Jun 2011
Posts: 11

PostPosted: Sat Jun 25, 2011 1:52    Post subject: Reply with quote
Code:
U-boot Ver:1.0.1.30 2009/10/12                                                 
                                                                               
                                                                               
Board: Ralink APSoC DRAM:  32 MB  1*32 MB                                     
============================================                                   
ASIC 3052_MP2 (Port5<->None)                                                   
Product Name: EAP9550                                                         
SDRAM CAS = 3(d1835272)                                                       
============================================                                   
                                                                               
Please choose the operation:                                                   
   1: Load system code to SDRAM via TFTP.                                     
                                                                               
1: System Load Linux to SDRAM via TFTP.                                       
 Please Input new ones /or Ctrl-C to discard                                   
        Input device IP (192.168.99.9) ==:192.168.99.9                         
        Input server IP (192.168.99.8) ==:192.168.99.8                         
        Input Linux Kernel filename (uImageEAP9550) ==:firmware.bin           
Using Eth0  device                                                             
TFTP from server 192.168.99.8; our IP address is 192.168.99.9                 
Filename 'firmware.bin'.                                                       
Loading: *                                                                     
ArpTimeoutCheck                                                               
Got ARP REPLY, set server/gtwy eth addr (00:23:5a:f1:a2:ad)                   
Got it                                                                         
T #                                                                           
 first block received                                                         
################################################################               
         #################################################################     
         #################################################################     
         #################################################################     
         #################################################################     
         #################################################################     
         #################################################################     
         #################################################################     
         #################################################################     
         #################################################################     
         #################################################################     
         #######                                                               
done                                                                           
Bytes transferred = 3691602 (385452 hex)                                       
File: env_flash.c, Func: saveenv, Line: 300                                   
Un-Protected 1 sectors                                                         
Erasing Flash...                                                               
                                                                               
 erase sector  = 3                                                             
Erased 1 sectors                                                               
Writing to Flash... done                                                       
Protected 1 sectors                                                           
                                                                               
LINUX started...                                                               
                                                                               
 THIS IS ASIC                                                                 
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.1.2) #6717 Wed Apr 13 13:1
                                                                               
 The CPU frequency set to 384 MHz                                             
32M RAM Detected!                                                             
CPU revision is: 0001964c                                                     
Determined physical RAM map:                                                   
 memory: 02000000 @ 00000000 (usable)                                         
Built 1 zonelists in Zone order.  Total pages: 8128                           
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squad
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.   
Primary data cache 16kB, 4-way, linesize 32 bytes.                             
Synthesized TLB refill handler (20 instructions).                             
Synthesized TLB load handler fastpath (32 instructions).                       
Synthesized TLB store handler fastpath (32 instructions).                     
Synthesized TLB modify handler fastpath (31 instructions).                     
Cache parity protection disabled                                               
cause = 90800068, status = 1100ff00                                           
PID hash table entries: 128 (order: 7, 512 bytes)                             
calculating r4koff... 003a9800(3840000)                                       
CPU frequency 384.00 MHz                                                       
Using 192.000 MHz high precision timer.                                       
console [ttyS1] enabled                                                       
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)                 
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)                   
Memory: 29472k/32768k available (2166k kernel code, 3296k reserved, 321k data,)
Mount-cache hash table entries: 512                                           
NET: Registered protocol family 16                                             
Generic PHY: Registered new driver                                             
NET: Registered protocol family 2                                             
Time: MIPS clocksource has been installed.                                     
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)                 
TCP established hash table entries: 1024 (order: 1, 8192 bytes)               
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)                       
TCP: Hash tables configured (established 1024 bind 1024)                       
TCP reno registered                                                           
Load Ralink DFS Timer Module                                                   
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)                         
devfs: boot_options: 0x1                                                       
squashfs: version 3.0 (2006/03/15) Phillip Lougher                             
io scheduler noop registered                                                   
io scheduler deadline registered (default)                                     
Ralink gpio driver initialized                                                 
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled       
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A                     
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A                     
rt3052 access driver initialization.                                           
PPP generic driver version 2.4.2                                               
PPP Deflate Compression module registered                                     
PPP BSD Compression module registered                                         
MPPE/MPPC encryption/compression module registered                             
NET: Registered protocol family 24                                             
PPPoL2TP kernel driver, V1.0                                                   
tun: Universal TUN/TAP device driver, 1.6                                     
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>                         
ralink flash device: 0x1000000 at 0xbf000000                                   
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank 
 Amd/Fujitsu Extended Query Table at 0x0040                                   
Ralink SoC physically mapped flash: Swapping erase regions for broken CFI tabl.
number of CFI chips: 1                                                         
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.       
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":             
0x00000000-0x00030000 : "uboot"                                               
0x00030000-0x00040000 : "uboot-config"                                         
0x00040000-0x00050000 : "factory-defaults"                                     
0x00050000-0x00120000 : "linux"                                               
0x00120000-0x00400000 : "rootfs"                                               
0x003f0000-0x00400000 : "nvram"                                               
Ralink APSoC Hardware Watchdog Timer                                           
u32 classifier                                                                 
    Actions configured                                                         
Netfilter messages via NETLINK v0.30.                                         
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)                           
ctnetlink v0.93: registering with nfnetlink.                                   
IPv4 over IPv4 tunneling driver                                               
GRE over IPv4 tunneling driver                                                 
ip_tables: (C) 2000-2006 Netfilter Core Team                                   
IPP2P v0.8.2 loading                                                           
ClusterIP Version 0.8 loaded successfully                                     
TCP bic registered                                                             
TCP cubic registered                                                           
TCP westwood registered                                                       
TCP highspeed registered                                                       
TCP hybla registered                                                           
TCP htcp registered                                                           
TCP vegas registered                                                           
TCP scalable registered                                                       
NET: Registered protocol family 1                                             
NET: Registered protocol family 17                                             
Welcome to PF_RING 3.2.1                                                       
(C) 2004-06 L.Deri <deri@ntop.org>                                             
NET: Registered protocol family 27                                             
PF_RING: bucket length    128 bytes                                           
PF_RING: ring slots       4096                                                 
PF_RING: sample rate      1 [1=no sampling]                                   
PF_RING: capture TX       No [RX only]                                         
PF_RING: transparent mode Yes                                                 
PF_RING initialized correctly.                                                 
PF_RING: registered /proc/net/pf_ring/                                         
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>                 
All bugs added by David S. Miller <davem@redhat.com>                           
MAC_ADRH -- : 0x00000000                                                       
MAC_ADRL -- : 0x00000000                                                       
                                                                               
eth2 mii.o query= phy_id:0, address:1 retval:7869                             
Ralink APSoC Ethernet Driver Initilization. v2.0  256 rx/tx descriptors alloca!
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256                         
MAC_ADRH -- : 0x0000000c                                                       
MAC_ADRL -- : 0x43305277                                                       
Trap instruction in kernel code[#1]:                                           
Cpu 0                                                                         
$ 0   : 00000000 00000000 00000001 00000000                                   
$ 4   : 00000000 8f838f83 00000000 00000002                                   
$ 8   : 000000aa 00000000 00000000 81168f00                                   
$12   : 00000001 ffffffff 52d9b780 00000000                                   
$16   : 00002000 80261230 8f838f83 00002000                                   
$20   : 811a0a00 8de60a38 811a0a00 80260000                                   
$24   : 00000000 80135308                                                     
$28   : 81050000 81051d50 00000000 8012f618                                   
Hi    : 00000002                                                               
Lo    : ffffffff                                                               
epc   : 8012f66c     Not tainted                                               
ra    : 8012f618 Status: 1100fc03    KERNEL EXL IE                             
Cause : 10800034                                                               
PrId  : 0001964c                                                               
Modules linked in:                                                             
Process swapper (pid: 1, threadinfo=81050000, task=802fe878)                   
Stack : 00000008 8029892c 8f838f83 802a0000 00000000 802fe878 8001c8ec 00000000
        00000000 00000000 003f0000 00000000 00002000 00002000 811a0a00 00000000
        81168f10 80261230 003f0000 8012a8fc 80029780 000000d0 81198000 00000000
        00000000 80134134 8de60a38 811b7c7c 810c6080 81051e70 00000000 81051e54
        81198000 81051e5c 802e0000 802d0000 802d0000 8012dc84 00009860 8012f598
        ...                                                                   
Call Trace:[<8001c8ec>][<8012a8fc>][<80029780>][<80134134>][<8012dc84>][<8012f]
                                                                               
Code: 70433002  24020001  00e3001a <006001f4> 00c54821  1082000c  00002812  24
Kernel panic - not syncing: Attempted to kill init!                           
Rebooting in 1 seconds..                                                       
                                                                               
                                                                               
U-boot Ver:1.0.1.30 2009/10/12                                                 
                                                                               
                                                                               
Board: Ralink APSoC DRAM:  32 MB  1*32 MB                                     
============================================                                   
ASIC 3052_MP2 (Port5<->None)                                                   
Product Name: EAP9550                                                         
SDRAM CAS = 3(d1835272)                                                       
============================================                                   
                                                                               
Please choose the operation:                                                   
   1: Load system code to SDRAM via TFTP.                                     
                                                                               
LINUX started...                                                               
                                                                               
 THIS IS ASIC                                                                 
init started: BusyBox v1.7.5 (2010-10-13 13:42:00 CST)                         
starting pid 131, tty '/dev/console': '/sbin/config_init'                     
Config Init version: 1.2.2.17 date: 2010/10/13                                 
Could not find Watchdog driver (/apps/lib/modules/2.6.21/kernel/arch/mips/rt28)
starting pid 178, tty '/dev/ttyS1': '/sbin/config_term'                       
************************************************************************       
*                                  EAP9550                             *       
************************************************************************       
                                                                               
KernelApp/Ramdisk Ver:1.2.2.17                   Date:2010/10/13               
console> cat: can't open '/apps/lib/modules/2.6.21/modulesApp.dep': No such fiy
ln: /sbin/./apps_init: File exists                                             
ln: /sbin/./httpsd: File exists                                               
sh: cannot create /proc/senao/ip_conntrack_interface: nonexistent directory   
sh: cannot create /proc/senao/ip_conntrack_interface: nonexistent directory   
sh: cannot create /proc/senao/ip_conntrack_interface: nonexistent directory   
sh: cannot create /proc/switch/power_status: nonexistent directory             
sh: cannot create /proc/switch/power_status: nonexistent directory
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1191

PostPosted: Fri Aug 26, 2011 17:13    Post subject: Unsupported Device Reply with quote
looks like nearly a month with no reply on this new smoke detector wireless N device...

Can we assume there will be no dd-wrt support for this device and remove it from the supported device list?

Fractal
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17480
Location: Hesse/Germany

PostPosted: Thu Nov 29, 2012 22:52    Post subject: Reply with quote
as you can see ascott go it booting. it should work with current builds
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Senao Devices All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum