Use build 15508 or higher to fix the VLAN GUI for that model. _________________ Read the forum announcements thoroughly! Be cautious if you're inexperienced.
Available for paid consulting. (Don't PM about complicated setups otherwise)
Looking for bricks and spare routers to expand my collection. (not interested in G spec models)
To do a 30-30-30 reset you must push the reset button with your router powered on.
NOTICE: you have to use a WIRED connection
with current build
hard-reset for 35 seconds
without turning it off-line, refresh IP and connecting to 192.168.1.1
password page is display and details entered - using simple name and password (no funky characters like %$)
now for a full hard-reset
35 seconds pressing reset button WITH power on
turning power OFF AND CONTINUE pressing reset button for another 35 seconds
turning power ON AND CONTINUE pressing reset button for another 35 seconds
change password again - it should request it when you access it
after, unplug the power cable for at least 30 seconds, physically pull the cable out
bring it power on-line
i am using a WNR3500L, and following advice from the Guru's at DD-WRT forum, i will be installing:
dd-wrt.v24-15940_NEWD-2_K2.6_big.bin
login into the router and upgrade the firmware with the of above. choose to reset the configuration at the same time.
the page goes into the usual horizontal bar, telling us to wait and after a while but eventually it comes back (or stops - just goto to http://192.168.1.1 manually)
login back in, and check your update by clicking on the right-upper corner on the firmware link. on the new page you will find your build details. in this case:
DD-WRT v24-sp2 (12/18/10) big
(SVN revision 15940)
so it is working again!!
now for the vlan setup configuration
objective
set a vlan to be a DMZ subnet
ideally i would like to make this to a single port; having two networks available through the same physical port.
but i could not work out how to do that. instead i will try to do it against all ports
firstly i have setup my laptop to have a vlan with VLAN TAGGING 9 (using ubuntu 10.10)
~# vconfig add eth0 9
~# ifconfig eth0.9 192.168.13.89
in the router using the web UI
on page VLANs, all ports are kept together on vlan1
on page Networking, i did the following:
on VLAN TAGGING (matching the tagging on my laptop)
add VLAN0 interface with VLAN1, tag number 9 prio 1
save and apply
on port setup
Network Configuration vlan1.9 = Unbridged
Masquerade / NAT = Enable
IP = 192.168.13.1
subnet mask = 255.255.255.0
save, apply and then rebooted
my latpop received the correct dhcp offer with ip range of 192.168.1.0/24
But i can not ping 192.168.13.1 (router IP on vlan1.9)
and i can find the correct entry on my laptop on the route
Destination Gateway Genmask Flags Metric Ref Use Iface
...
192.168.13.0 * 255.255.255.0 U 0 0 0 eth0.9
on the router ssh i find the following info:
192.168.13.1
root@DD-WRT:~# nvram show | grep vlan1.9
vlan1.9_mtu=1500
vlan1.9_nat=1
vlan1.9_multicast=0
vlan1.9_bridged=0
vlan1.9_ipaddr=192.168.13.1
vlan1.9_netmask=255.255.255.0
vlan_tags=vlan1>9>1
size: 24824 bytes (7944 left)
Don't use VLAN tagging on the networking page for Broadcom based routers, use the VLAN page. See the wiki for more info. _________________ Read the forum announcements thoroughly! Be cautious if you're inexperienced.
Available for paid consulting. (Don't PM about complicated setups otherwise)
Looking for bricks and spare routers to expand my collection. (not interested in G spec models)