Hi to all Please can you help me [D-LINK DSL-2640b]

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Author Message
dimoni
DD-WRT Novice


Joined: 06 Apr 2011
Posts: 2
Location: Planeta Tierra

PostPosted: Wed Apr 06, 2011 13:58    Post subject: Hi to all Please can you help me [D-LINK DSL-2640b] Reply with quote
Hi to all dears friends
I searching a CFE.BIN for D-link 2640B european version
The revision of harwware is B2
I posting some lite information of my device when worked.

Code:

Linux version 2.6.32.25 (openwrt@ampere) (gcc version 4.3.3 (GCC) ) #1 Fri Nov 19 21:51:29 PST 2010
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-6.5
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: D-4P-W
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 802981f0, node_mem_map 802df000
  Normal zone: 32 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13284k/16384k available (2140k kernel code, 3100k reserved, 453k data, 140k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x001fff]
pci 0000:01:1e.0: CardBus bridge, secondary bus 0000:02
pci 0000:01:1e.0:   IO window: 0x8008000-0x80080ff
pci 0000:01:1e.0:   IO window: 0x8008400-0x80084ff
pci 0000:01:1e.0:   MEM window: 0x38000000-0x3fffffff
PCI: Enabling device 0000:01:1e.0 (0000 -> 0003)
PCI: Setting latency timer of device 0000:01:1e.0 to 64
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.337:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 25
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
 CFI mfr 0x000000c2
 CFI id  0x000022a8
 Amd/Fujitsu Extended Query Table at 0x0040
  Amd/Fujitsu Extended Query version 1.1.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type D-4P-W
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset f0000 and length 300000
bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 10000 and length 3e0000
bcm963xx_flash: Spare partition is 2a0000 offset and length 150000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000f0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000f0000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2A0000, len=150000
0x0000002a0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x0000003f0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: ppp
Registered led device: ppp-fail
Registered led device: power
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 140k freed
Please be patient, while OpenWrt loads ...
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: port 1(eth1) entering forwarding state
Compat-wireless backport release: compat-wireless-2010-10-14-7-gab01eca
Backport based on wireless-testing.git master-2010-10-19
cfg80211: Calling CRDA to update world regulatory domain
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: found a 5325! It's a 5350.
cfg80211: World regulatory domain updated:
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL, GPIO LED Mask: 0x000f, Firmware-ID: FW13 ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (209 buckets, 836 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state


So hi think a bad flash firmware, from another revision and the router is bricked
Can use te Ejtag from tornado mod and the router is recognized


It's much apreciated some help and came you send the CFE.BIN for recover my broadcom 96348 based router. this is posible, ok.
Thanks, many thanks in advanced.

pd:Sorry for my bad english i'am a spanish user forum
Sponsor
gobbledigook
DD-WRT Guru


Joined: 06 Apr 2009
Posts: 727

PostPosted: Wed Apr 06, 2011 15:24    Post subject: Reply with quote
that router does not appear on the supported devices list? what exactly have you flashed it with?

DSL routers are not widely supported by dd-wrt...

_________________
Please search the forum and dd-wrt wiki before posting, you may be surprised Wink
useful links:
Optware the right way
list of optware packages
broadcom announcements, peacock and recommended builds
dimoni
DD-WRT Novice


Joined: 06 Apr 2011
Posts: 2
Location: Planeta Tierra

PostPosted: Wed Apr 06, 2011 15:52    Post subject: Reply with quote
gobbledigook wrote:
that router does not appear on the supported devices list? what exactly have you flashed it with?

DSL routers are not widely supported by dd-wrt...


First of all thank you very much for your prompt response.
Very well that dd-wrt does not support my router. But I want to say that I have many days reading this forum and to share various CFE, s for different models including the best known and Linksys.
I really have psad a rare case and is as follows.
This router if it is recognized by open-wrt in fact he had as seen in my previous post its firmware backfire
But one day by some of the chances and bringing me extremely well I did not think another thing that is not yet upgrade to a version of firmware d-link to return to their initial state. To my surprise that I did flash it with a version of H / W wrong, yet do not understand how I put it .. I'm sorry.
I've been watching me this website http://pudeev.livejournal.com/33915.html
in Russian and the truth is that it has served me very helpful.
I am also asking for help in open-wrt as well as here.
As if that would happen to this router tubiera alguine 2640B and by chance had made a copy / backup of your original cfe.
I tried several here and many of this forum, I put my jtag home but of course not for the particular model ....

And so I throw a cry of hope to see if anyone can help me do not I think that is, if not rather to have a CFE.BIN for my model of router.

As I said thank you very much for answering, I am very grateful.
At the moment not lost hope of finding it.
Greetings.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum