Author
Message
Fractal DD-WRT Guru Joined: 19 Apr 2010 Posts: 1243
Posted: Tue May 03, 2011 15:03 Post subject: Linksys/Cisco E2500 for DD-WRT
I have been doing some testing with the E2500 unit... I think the port is going to be pretty easy. I will attach some output dumps from the e2500 that I conducted during my testing.... Today I noticed that walmart/staples/officedepot are no longer carrying the E2K/E3K/ and are moving to the E1500/1700/2500/4200. So porting to E2500 is not a bad idea...
Code:
#
# dmesg[J
# cat /proc/cpuinfo [J
system type : Broadcom BCM5357 chip rev 1
processor : 0
cpu model : MIPS 74K V4.9
BogoMIPS : 149.50
wait instruction : no
microsecond timers : yes
tlb_entries : 64
extra interrupt vector : no
hardware watchpoint : yes
ASEs implemented : mips16 dsp
VCED exceptions : not available
VCEI exceptions : not available
unaligned_instructions : 40
dcache hits : 2147483648
dcache misses : 736174114
icache hits : 2147483648
icache misses : 3757207204
instructions : 2147483648
CFE BOOT:
Code:
Boot version: v4.12
The boot is CFE
Nothing...
No country code find
### CLKDIV= 0x20e0842, SFlashClkDiv=2 clkdivsf=2 ###
### Change it to 0x20e0842 (2) ###
Device eth0: hwaddr C0-C1-C0-XX-XX-XX, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Header CRC: 0xBEAC3156
Calculate CRC: 0xBEAC3156
internal pic as well:
Last edited by Fractal on Tue May 03, 2011 15:13; edited 1 time in total
Back to top
Sponsor
Dark_Shadow DD-WRT Guru Joined: 31 Aug 2009 Posts: 2448 Location: Third Rock from the Sun
Back to top
Fractal DD-WRT Guru Joined: 19 Apr 2010 Posts: 1243
Posted: Tue May 03, 2011 15:13 Post subject:
updated with pic...
Fractal
Back to top
Fractal DD-WRT Guru Joined: 19 Apr 2010 Posts: 1243
Posted: Tue May 03, 2011 15:16 Post subject:
Getting closer:
Code:
Linux version 2.6.22-g28ac0946-dirty (root@GavinPC.localdomain) (gcc version 4.2.3) #339 Wed Feb 23 20:27:27 CST 2011
CPU revision is: 00019749
Found a 8MB ST compatible serial flash
wombo_reset set to gpio 23
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0 -> 16384
HighMem 16384 -> 16384
early_node_map[1] active PFN ranges
0: 0 -> 16384
Built 1 zonelists. Total pages: 16384
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit mem=64M
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM5357 rev 1 at 300 MHz
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60428k/65536k available (2705k kernel code, 5048k reserved, 522k data, 208k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: no core
PCI: Fixing up bus 0
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
gpio_init: power pulse time 7
Register DIAG LED in /proc/sys/diag_blink.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
fuse init (API version 7.8)
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
NET: Registered protocol family 24
pflash: found no supported devices
sflash: squash filesystem with lzma found at block 1706
Creating 4 MTD partitions on "sflash":
0x00000000-0x00040000 : "boot"
0x00040000-0x007f0000 : "linux"
0x001aaa24-0x007f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x007f0000-0x00800000 : "nvram"
u32 classifier
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
edward ====to register conntrack protocol helper for esp:
nf_conntrack_rtsp v0.6.21 loading
GRE over IPv4 tunneling driver
nf_nat_rtsp v0.6.21 loading
edward =======nf_nat_proto_esp_init
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 208k freed
Back to top
Dark_Shadow DD-WRT Guru Joined: 31 Aug 2009 Posts: 2448 Location: Third Rock from the Sun
Back to top
Fractal DD-WRT Guru Joined: 19 Apr 2010 Posts: 1243
Posted: Tue May 03, 2011 15:46 Post subject:
Chips:
Wireless Radio = BCM5358U (2.4ghz)
Wireless Radio = BCM43236 (5.8ghz)
Back to top
matthileo DD-WRT Novice Joined: 30 May 2011 Posts: 3
Posted: Mon May 30, 2011 19:46 Post subject:
Any word on how this is going?
Back to top
jaksco DD-WRT Novice Joined: 12 Jun 2011 Posts: 3
Posted: Sun Jun 12, 2011 19:17 Post subject:
Any development?
Back to top
sektor DD-WRT Novice Joined: 25 Dec 2006 Posts: 2 Location: Florida
Posted: Tue Jun 28, 2011 22:15 Post subject: E2500 updates
Any updates on possible firmware?
Back to top
doublej472 DD-WRT Novice Joined: 29 Jun 2011 Posts: 2
Posted: Wed Jun 29, 2011 18:17 Post subject: E2500 router
How much of the software has been done so far?
Back to top
Fractal DD-WRT Guru Joined: 19 Apr 2010 Posts: 1243
Posted: Wed Jun 29, 2011 19:44 Post subject: Re: E2500 router
The CFE has been dumped and are just awaiting eko's response... The CFE dumped info is in this thread.
Fractal
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=140536
doublej472 wrote: How much of the software has been done so far?
Back to top
doublej472 DD-WRT Novice Joined: 29 Jun 2011 Posts: 2
Posted: Thu Jun 30, 2011 2:45 Post subject: Re: E2500 router
Thanks
Back to top