joedr
DD-WRT Novice
Joined: 03 Jan 2011
Posts: 7
|
 Posted: Sat Aug 27, 2011 17:26 Post subject: LAN Ports not working after reboot - Senao ESR-9752 |
 |
All,
I am running into a very unique situation on my ESR-9752.
So far, I am able to drop any version of the firmware using the serial method. Even configure the router as Repeater and Repeater Bridge.
I verified that the router is working as expected. However, when I reboot the router via the admin page or via terminal.... The router reboots and everything is working fine except the LAN ports. For some reason, the LAN ports stop working and there is no way to enable them.
I tried 3 or 4 different builds and getting the same result. All work fine before reboot and after reboot only the LAN ports stop working.
Does anybody had similar situation? Any ideas or checks to help me diagnose this issue?
Thanks!
Joed |
|
joedr
DD-WRT Novice
Joined: 03 Jan 2011
Posts: 7
|
| Posted: Sat Aug 27, 2011 17:38 Post subject: Sample from terminal |
|
This is the output on terminal during power on and the one where the LAN ports don't work.
| Code: | U-boot Ver:1.0.1.2 2009/09/25
Board: Ralink APSoC DRAM: 16 MB 1*16 MB
============================================
ASIC 3052_MP2 (Port5<->None)
Product Name: ESR-9752
SDRAM CAS = 3(d1835272)
============================================
Please choose the operation:
1: Load system code to SDRAM via TFTP.
LINUX started...
THIS IS ASIC
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.1.2) #6706 Wed Apr 13
12:17:55 CEST 2011
The CPU frequency set to 384 MHz
16M RAM Detected!
CPU revision is: 0001964c
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Built 1 zonelists in Zone order. Total pages: 4064
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4
rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 90800018, status = 1100ff00
PID hash table entries: 64 (order: 6, 256 bytes)
calculating r4koff... 003a9800(3840000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
console [ttyS1] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13228k/16384k available (2166k kernel code, 3156k reserved, 321k
data, 120k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
Load Ralink DFS Timer Module
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
rt3052 access driver initialization.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ralink flash device: 0x1000000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit
bank
Amd/Fujitsu Extended Query Table at 0x0040
Ralink SoC physically mapped flash: Swapping erase regions for broken CFI
table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
found squashfs at 124000
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "uboot"
0x00030000-0x00040000 : "uboot-config"
0x00040000-0x00050000 : "factory-defaults"
0x00050000-0x003e0000 : "linux"
0x00124000-0x003e0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force
read-only
0x003e0000-0x003f0000 : "nvram"
Ralink APSoC Hardware Watchdog Timer
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
IPP2P v0.8.2 loading
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <deri@ntop.org>
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
MAC_ADRH -- : 0x00000000
MAC_ADRL -- : 0x00000000
eth2 mii.o query= phy_id:0, address:1 retval:7849
Ralink APSoC Ethernet Driver Initilization. v2.0 256 rx/tx descriptors
allocated, mtu = 1500!
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256
MAC_ADRH -- : 0x0000000c
MAC_ADRL -- : 0x43305277
decode /dev/mtdblock4
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 120k freed
start service
starting Architecture code for rt2880
rt2860v2_ap: module license 'unspecified' taints kernel.
phy_tx_ring = 0x00957000, tx_ring = 0xa0957000
phy_rx_ring0 = 0x00958000, rx_ring0 = 0xa0958000
RT305x_ESW: Link Status Changed
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 710000
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1002
switch reg write offset=44, value=1001
switch reg write offset=48, value=1001
switch reg write offset=70, value=ffff417e
sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent
directory
sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent
directory
sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent
directory
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device br0 entered promiscuous mode
Algorithmics/MIPS FPU Emulator v1.5
device vlan1 entered promiscuous mode
device eth2 entered promiscuous mode
sh: ead: not foundbr0: port 1(vlan1) entering learning state
device br0 left promiscuous mode
device br0 entered promiscuous mode
device br0 left promiscuous mode
device br0 entered promiscuous mode
RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
0x1300 = 00064380
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
0x1300 = 00064380
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
wland: No such file or directory
device vlan2 entered promiscuous mode
SIOCGIFFLAGS: No such device
device vlan2 left promiscuous mode
SIOCGIFFLAGS: No such device
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
etherip: Ethernet over IPv4 tunneling driver
sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent
directory
sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent
directory
sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent
directory
DD-WRT v24-sp2 std (c) 2011 NewMedia-NET GmbH
Release: 04/13/11 (SVN revision: 16785)
ÿ
DD-WRT login:
|
|
|
