I could possibly do some testing.. I have this particular model at home. What exactly would I have to do?
Testing out with a multimeter the gpio pin assignments for the different LED's.
A few gpio's can be found by watching the LED's while doing gpio enable/gpio disable commands but most of them has to be checked with a multimeter.
Tell me if you are able to do that and I can then give you further instructions.
other LEDs are controled by two 74HC595s ,whose data-sheet can be found at http://www.nxp.com/documents/data_sheet/74HC_HCT595.pdf
GPIO 0 connected to pin 14 for data source, GPIO 1 connected to pin 11 for shift register clock input ,GPIO 11 connected to pin 12 for storage register clock input,GPIO 5 should set to enable for power supply,GPIO 4 connected to ping 13 for output enable,gpio enable 4 can turn off all LEDs without lost status and gpio disable 4 can restore them.
except download LED group,there are 7 LED signs on front panel,they are security、wireless、wired、storage、router、modem、internet
from top to down。every sign has two colors,blue first and red second expect router sign,serial turn on sequences are shown blew
router sign also contains two LEDs ,not two color but two separate blue LEDs
gpio 0 disable
to set one LED on
gpio 0 enable
to set one LED off
gpio enable 1
gpio disable 1
set shift register serial
this need to repeat 14 times to set every LEDs
gpio disable 11
gpio enable 11
flush shift register data to storage register and show at the front panel.
gpio 4 always should disable and gpio 5 should enable.
click images can see large images
Last edited by loveni on Wed Jun 08, 2011 1:05; edited 1 time in total
Good job you have done there loveni, the same type of circuit is used in the v2 version (Ralink RT3052 cpu) of the router so I had already figured out the function by looking in the GPL code for that one and it was merely a question of which i/o-pins had been used in the v3. (there is no GPL code available for the v3).
I doubt that Eko is willing to implement a special led-gpio function for this router when all other Broadcom based routers works with one LED on it's own gpio pin and not a serial-to-parallel shift register like this.
It would be the only Broadcom router with a different gpio module and would need a specific build for the router instead of a general build..
I'll email Eko and give him a heads up and a pointer to your posts in case he hasn't seen them.
I can implement it, similar I just did for Netgear wndr4000 (one 8 bit shift register). _________________ Professional debrick service for EU countries for small fee.
Send inquiries to: debrick at dd-wrt dot si
Have a brick you don't need?
Paypal & Amazon.com gift cards are welcome. Every $ or € counts. Email: donate at dd-wrt dot si
Posted: Wed Aug 17, 2011 23:57 Post subject: How to install & USB support
I have this router and your latest dd-wrt.v24-16309_NEWD-2_K2.6_mini.bin for it. I have tried to update the firmware from the default belkin interface and no go. What is the procedure to install this version on this router? Ill check the peacock thread but since this router is WIP I dont want to brick it doing something wrong. Hope you can help.
Also is USB support available with this build or can it be added? I see there is a procedure to add USB support but I am a bit of a noob and am just learning DD-wrt in and outs.
Posted: Fri Aug 19, 2011 4:18 Post subject: How to x2
I'm looking for the same thing. I have this router and can not figure out how to get DD-wrt onto it or any other 3rd party firmware for that matter. Can someone help. Looks like it takes TFTP but there is no confirmation of that here nore in the DD-wrt wiki... Whats the process?
Posted: Fri Aug 19, 2011 7:28 Post subject: ahhh that makes sense
Are you sure I can go to a mega release after? The highest version I have found so far is v24-17084_NEWD-2_K2.6_mini_f5d8235v3. I have not seen mega releases but that is what Im looking for as those have USB support. Is USB working on this router under DD-wrt? I know it can be added through some tinkering but being a noob I was hoping it would be included in the latest build.
Update: I have been able to go from 16302 to 16309 but can not seen to update to version 17084 or version 16785 that you pointed to in the brainslayer k26 updates. Any idea why? I get the message upgrade failed when I tried. Is there another incremental update I need to do first to move to those?
I know its been a while since this topic was posted on, and its an obvious question (I'm new to dd-wrt)but I can't seem to be able to flash my box with DD-WRT. I assumed in LOM's post that uploading meant using the web gui (it used that terminology in the wiki) but when I try to flash either of the new firmwares, it just reboots the box into stock firmware, so its not actually flashing it. I also tried using TFTP, but I may have not been doing it right. (i followed the instructions here http://www.dd-wrt.com/wiki/index.php/TFTP_flash for mac)
My box isn't very reliable so I'm keen to try and put DD-WRT on it. Any help anyone can offer would be appreciated
I assumed in LOM's post that uploading meant using the web gui (it used that terminology in the wiki) but when I try to flash either of the new firmwares, it just reboots the box into stock firmware, so its not actually flashing it.
Others have succeeded so there is nothing wrong with the firmware.
Trailed build (with router name in the file name) for first time flashing from Belkin stock firmware to dd-wrt.
Firewall and antivirus program off, upload the file via Belkins web gui for firmware update.
Try another browser or a windows machine if you still can't get a successful flash.