Surf@home 2 ?

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> ARM oder PPC basierte Hardware
Author Message
Simon94
DD-WRT Novice


Joined: 24 Jul 2009
Posts: 32

PostPosted: Fri Jul 24, 2009 3:58    Post subject: Surf@home 2 ? Reply with quote
Wunderschönen guten Tag.

Ich habe den o.g. Router. Dieser verfügt über 32 Mb Ram sowie 16 Mb Flashspeicher.
Der Prozessor ist ein IXP425.

Darauf läuft OpenRG (eine kommerziell genutze Router FW), dieses wiederum verwendet einen 2.4er Kernel.


Das Teil hat scheinbar Intern nen USB Port, an welchem ein USB2Serial Konverter hängt. Daher schlussfolgere, dass hieran das Display hängt.

Krieg ich auf die Kiste eine WRT-FW?

Und die entscheidene Frage, wie Krieg ichs rauf?!



Hier noch paar Ausgaben:
Code:
/ # cat /proc/kmsg
<4>Linux version 2.4.21openrg-rmk1 #2 Wed Nov 30 12:51:10 CET 2005
<4>CPU: XScale-IXP4xx/IXC11xx revision 1
<4>Machine: Intel IXP425 Possio PX40
<4>Memory range 0x1fff000-0x2000000 is excluded because of PCI DMA bug
<4>On node 0 totalpages: 8192
<4>zone(0): 8192 pages.
<4>zone(1): 0 pages.
<4>zone(2): 0 pages.
<4>Kernel command line: console=ttyS1,115200 root=/dev/ram0 rw nohalt panic=2
<7>Relocating machine vectors to 0xffff0000
<4>Using IXP425 Timer 0 as timer source
<4>Calibrating delay loop... 266.24 BogoMIPS
<6>Memory: 32MB = 32MB total
<5>Memory: 26640KB available (1416K code, 4267K data, 52K init)
<6>XScale Cache/TLB Locking Copyright(c) 2001 MontaVista Software, Inc.
<6>Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
<6>Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<4>Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
<4>Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
<4>POSIX conformance testing by UNIFIX
<4>PCI Autoconfig: Found CardBus bridge, device 14 function 0
<4>PCI Autoconfig: Found Bus 0, Device 14, Function 0
<4>PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bfff000
<4>PCI Autoconfig: Found Bus 0, Device 15, Function 0
<4>PCI Autoconfig: BAR 0, Mem, size=0x2000, address=0x4bffc000
<4>Scanning bus 00
<4>Found 00:00 [8086/8500] 000b40 00
<6>PCI: Calling quirk c0009e08 for 00:00.0
<6>PCI: Calling quirk c00a0bf8 for 00:00.0
<4>Found 00:70 [104c/ac56] 000607 02
<6>PCI: Calling quirk c0009e08 for 00:0e.0
<6>PCI: Calling quirk c00a0bf8 for 00:0e.0
<4>Found 00:78 [1814/0201] 000280 00
<6>PCI: Calling quirk c0009e08 for 00:0f.0
<6>PCI: Calling quirk c00a0bf8 for 00:0f.0
<4>Fixups for bus 00
<6>PCI: bus0: Fast back to back transfers disabled
<4>Scanning behind PCI bridge 00:0e.0, config 000000, pass 0
<4>Scanning behind PCI bridge 00:0e.0, config 000000, pass 1
<4>Bus scan for 00 returning with max=04
<4>
<4>>> PCI IRQ 0.1 : -1
<3>PCI fixup irq: (PCI device 8086:8500 (Intel Corp.)) got 0
<4>
<4>>> PCI IRQ 14.1 : 25
<3>PCI fixup irq: (Texas Instruments PCI1510 PC card Cardbus Controller) got 25
<4>
<4>>> PCI IRQ 15.1 : 7
<3>PCI fixup irq: (PCI device 1814:0201) got 7
<6>PCI: Calling quirk c0010214 for 00:00.0
<6>PCI: Calling quirk c0009f28 for 00:0e.0
<6>PCI: Calling quirk c0010214 for 00:0e.0
<6>PCI: Calling quirk c0010214 for 00:0f.0
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<4>Starting kswapd
<7>i2c-core.o: i2c core module
<7>i2c-dev.o: i2c /dev entries driver module
<7>i2c-algo-bit.o: i2c bit algorithm module
<4>i2c-dev.o: Registered 'IXP425 I2C Adapter' as minor 0
<4>
<4>Random: 0x65b5a2be
<4>pty: 256 Unix98 ptys configured
<6>Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PC
 enabled
<6>ttyS00 at 0xff000003 (irq = 15) is a XScale UART
<6>ttyS01 at 0xff001003 (irq = 13) is a XScale UART
<6>SCSI subsystem driver Revision: 1.00
<6>Linux Kernel Card Services 3.1.22
<6>  options:  [pci] [cardbus]
<4>PCI: enabling device 00:0e.0 (0140 -> 0143)
<6>usb.c: registered new driver usbdevfs
<6>usb.c: registered new driver hub
<4>Yenta IRQ list 0000, PCI irq25
<4>Socket status: 30000820
<6>Initializing USB Mass Storage driver...
<6>usb.c: registered new driver usb-storage
<6>USB Mass Storage support registered.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<6>IP: routing cache hash table of 512 buckets, 4Kbytes
<6>TCP: Hash tables configured (established 2048 bind 4096)
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<1>802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
<1>All bugs added by David S. Miller <davem@redhat.com>
<6>cs: cb_alloc(bus 1): vendor 0x1033, device 0x0035
<4>Found 01:00 [1033/0035] 000c03 00
<4>PCI: enabling device 01:00.0 (0000 -> 0002)
<4>PCI: Enabling bus mastering for device 01:00.0
<6>host/usb-ohci.c: USB OHCI at membase 0xc2804000, IRQ 25
<6>host/usb-ohci.c: usb-01:00.0, PCI device 1033:0035
<6>usb.c: new USB bus registered, assigned bus number 1
<6>hub.c: USB hub found
<6>hub.c: 1 port detected
<4>Found 01:01 [1033/0035] 000c03 00
<4>PCI: enabling device 01:00.1 (0000 -> 0002)
<4>PCI: Enabling bus mastering for device 01:00.1
<6>host/usb-ohci.c: USB OHCI at membase 0xc280a000, IRQ 25
<6>host/usb-ohci.c: usb-01:00.1, PCI device 1033:0035
<6>usb.c: new USB bus registered, assigned bus number 2
<6>hub.c: USB hub found
<6>hub.c: 1 port detected
<4>VFS: Mounted root (tmpfs filesystem).
<4>Mount of initial cramfs successful
<6>Freeing init cramfs memory: 32K
<6>Freeing init memory: 52K
<4>Mounting cramfs image at 'cramfs'
<4>loading license key: possio
<4>loading license key: possio
<4>loading license key: possio
<5>cfi_cmdset_0001: Erase suspend on write enabled
<7>0: offset=0x0,size=0x20000,blocks=128
<4>Using buffer write method
<4>Using predefined MTD partitions.
<5>Creating 1 MTD partitions on "IXP425 Flash Bank 0":
<5>0x00000000-0x01000000 : "openrg"
<6>hub.c: new USB device 01:00.1-1, assigned address 2
<4>usb.c: USB device 2 (vend/prod 0xaf0/0x6300) is not claimed by any active dr
ver.
<4>lcdm.c: Loading lcd
<4>I2C: ds1050_attach
<4>DS1050 returned 18
<6>Initializing Nozomi driver (build date: Nov 30 2005 12:39:26)
<4>Module init.
<4>Intel CSR QMGR & NPE(s) init done.
<4>Initializing ixp425_eth driver 0.0.8
<4>Found PHY 0 at 1
<4>PHY 0 MAC address is:        04:04:04:04:04:04
<4>PHY 1 MAC address is:        06:06:06:06:06:06
<4>IPV4 device driver registered
<6>usb.c: registered new driver serial
<6>usbserial.c: USB Serial support registered for Generic
<6>usbserial.c: Generic converter detected
<6>usbserial.c: Generic converter now attached to ttyUSB0 (or usb/tts/0 for dev
s)
<6>usbserial.c: Generic converter detected
<6>usbserial.c: Generic converter now attached to ttyUSB1 (or usb/tts/1 for dev
s)
<6>usbserial.c: Generic converter detected
<6>usbserial.c: Generic converter now attached to ttyUSB2 (or usb/tts/2 for dev
s)
<6>usbserial.c: USB Serial Driver core v1.4
<6>hw_button: add: button_id=1, gpio_pin=5, irq=22
<6>hw_button: add: button_id=2, gpio_pin=6, irq=23
<6>hw_button: add: button_id=3, gpio_pin=7, irq=24
<6>hw_button: add: button_id=4, gpio_pin=12, irq=29
<6>hw_button: add: button_id=5, gpio_pin=2, irq=19
<6>Freeing modfs memory: 864K
<4>Unloading lcd
<4>PHY 0 MAC address is:        00:09:8c:00:85:40
<4>PHY 0 MAC address is:        00:09:8c:00:85:40
<4>ixp0: Entering promiscuous mode
<6>device ixp0 entered promiscuous mode
<4>STP: ixp0 enters blocking mode
<6>device ra0 entered promiscuous mode
<4>STP: ra0 enters blocking mode
<4>STP: ixp0 enters blocking mode
<4>STP: ra0 exits blocking mode
<4>STP: ixp0 exits blocking mode


Code:
/ # cat /proc/cpuinfo
Processor       : XScale-IXP4xx/IXC11xx rev 1 (v5b)
BogoMIPS        : 266.24
Features        : swp half thumb fastmult edsp

Hardware        : Intel IXP425 Possio PX40
Revision        : 0000
Serial          : 0000000000000000


Code:
/ # cat /proc/meminfo
        total:    used:    free:  shared: buffers:  cached:
Mem:  28250112 15245312 13004800        0        0  4780032
Swap:        0        0        0
MemTotal:        27588 kB
MemFree:         12700 kB
MemShared:           0 kB
Buffers:             0 kB
Cached:           4668 kB
SwapCached:          0 kB
Active:           1300 kB
Inactive:         5960 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:        27588 kB
LowFree:         12696 kB
SwapTotal:           0 kB
SwapFree:            0 kB


Danke schonmal im vorraus Wink[/code]
Sponsor
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17379
Location: Hesse/Germany

PostPosted: Fri Jul 24, 2009 7:50    Post subject: Reply with quote
no board no port
_________________
GEGEN die EEG-UMLAGE auf EIGENVERBRAUCH!
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
Simon94
DD-WRT Novice


Joined: 24 Jul 2009
Posts: 32

PostPosted: Fri Jul 24, 2009 8:33    Post subject: Reply with quote
Was bitte?

Edit:

http://dd-wrt.com/wiki/index.php/MI424WR

Das Ding hat dieselbe Linux Distri wie mein Router drauf. Auch CPU, Flash und RAM sind gleich. Der Ethernetadapter is auch der selbe. Kann ich einfach so vorgehen wies beschrieben is?
masko72
DD-WRT Novice


Joined: 22 May 2007
Posts: 5

PostPosted: Sun Aug 14, 2011 8:24    Post subject: Reply with quote
Hi!

I have many board of them, resulting from a 0ption clearance blowout
0ption kept them away for warranty purposes... now warranty has ended for that model, and they 'scraped' the boards Very Happy

There are bare board only, without pcmcia HSDPA cards and plastic housings... so will be useful if reflashed with DD-WRT and usable at least as AP/bridge/repeater

I can donate 8-10 of these boards to you, to test if possible to adapt an existing firmware e.g.: from MI424WR

Let me know details and availability - Rgds C.M.
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17379
Location: Hesse/Germany

PostPosted: Sun Aug 14, 2011 12:18    Post subject: Reply with quote
do
http://www.dd-wrt.com/site/support/router-detection

_________________
GEGEN die EEG-UMLAGE auf EIGENVERBRAUCH!
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
soldiaz
DD-WRT Novice


Joined: 29 Oct 2011
Posts: 1

PostPosted: Sat Oct 29, 2011 13:49    Post subject: Reply with quote
Dear folks! I am interessted in Doing the same as Simon94. Is it just that easy to follow the steps for the mentioned hardware`?

Kind regards Soldiaz
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> ARM oder PPC basierte Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum