Joined: 06 Jun 2006 Posts: 7463 Location: Dresden, Germany
Posted: Sat Jul 23, 2011 13:52 Post subject: Re: configurar dd-wrt para antena wifi
95salo wrote:
BrainSlayer quisiera saber como debo configurar el dd-wrt std ( 14896) en router linksys wrt160nl para conectarle una antena hechiza ( antena wifi jolly rogers)la hice
con el proposito de acceder a internet de forma gratuitamente a travez de esta antena
como debo hacerlo ,configurarlo etc
gracias
emmanuel
sorry. i do not speak spanish _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Posted: Tue Feb 07, 2012 12:34 Post subject: Re: Bricked Unifi AP
odewitt wrote:
BrainSlayer wrote:
unifi support is now done and dd-wrt works on it.
Brand New Unifi AP - Bricked by DD-Wrt
..........
Thanks
John
Did you use ddwrt and instructions by BraySlayer?
I have few more questions for BrainSlayer.
1) is this the most recent version of ddwrt for Unifi?
2) How to get back to original FW if i would need? It would be nice if you could upload restore guide.
If your bootloader is undamaged, you can get in via serial console. You will need a serial to TTL adapter, which you can build yourself if you want following the initial part of this tutorial I wrote:
5. It's important to reboot once more after the whole bootup procedure has finished, sometimes there are settings not properly configured until the second boot.
here the test images + initial installation instructions
Hi BrainSlayer,
i have tried you bin and install.txt instructions. Flashing proccess goes well, but after:
1) I see only SSID "ddwrt"
2) I can connect with client to Unifi with ddwrt firmware and SSID "ddwrt", but doesnt work correctly. For example my phone get from dhcp server correct gateway (and internet work fine) but laptop get wrong gateway. If i connect not via Unifi laptop it gets correct GW.
3) The biggest problem is that i cant find any IP addrees which should Unifi use (before flashing i setup static 192.168.1.20, which work fine till flashed) so i cant connect to unifi and manage anything. Neither via http nor ssh. Also ping doesnt work.
4) AP Unifi keep flashing green light, i am not sure if it is some kind of status warning.
i am stupid and you should write better instructions!
At first you should specify that after flashing ddwrt firmware IP address of Unifi AP is set to 192.168.1.1 and also there is activated DHCP server by default. In my case the IP colidate with our server and also dhcp server.
I was also very surprised that this ddwrt is only 24h trial. If i know before it that this version is paid i will probably not lost time with try. 24h for some testing isnt much if you try it in the Friday afternoon before the weekend
I swear I read lot of artickles and guides here. If you think i have not read the right one please point me else please dont criticize me.
-I have tried ssh and telnet into the ddwrt without luck. SSH/telnet daemon was enabled and also managment via SSH/telnet was enabled via WebGUI. Maybe you disable this option in non activated FW?
-Also i have tried several fw versions 18687, 18024, 18007, 18000, 17967 because i have found artickle with informations that some version has not working ssh/telnet. After flashing 17967 i bricked my UNIFI, i cant ping anymore and LED doesnt light, just flash a while(orange) every ~1 minute.
-i cant get to recovery mode because uploading via TFTP doesnt succeedded
-the last solution i have found is get SERIAL to TTL converter, but i cant find this anywhere in my country
So i am very disapointed. I wait so long for any response from your team and the result is that i have bricked Unifi.