17967 through 18007 WRT400N Semi-Brick

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page 1, 2  Next
Author Message
Dark_Shadow
DD-WRT Guru


Joined: 31 Aug 2009
Posts: 2430
Location: Third Rock from the Sun

PostPosted: Fri Dec 09, 2011 12:58    Post subject: 17967 through 18007 WRT400N Semi-Brick Reply with quote
I have bricked and unbricked many broadcom units, but never an atheros. I flashed 17967 and lost communication via cable and did all the proper resets. I am thinking I can breack into the boot and start tftpd, but do not know the proper command. anywho here is the boot log after flash.

Code:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.12.09 07:41:31 =~=~=~=~=~=~=~=~=~=~=~=
þ

U-Boot 1.1.4 (Oct 22 2008 - 12:35:32)

AP94 (ar7100) U-boot 0.0.12
DRAM:  b8050000: 0xc0140180
32 MB
Top of RAM usable for U-Boot at: 82000000
Reserving 4308k for U-Boot at: 81bc8000
Reserving 192k for malloc() at: 81b98000
Reserving 44 Bytes for Board Info at: 81b97fd4
Reserving 36 Bytes for Global Data at: 81b97fb0
Reserving 128k for boot params() at: 81b77fb0
Stack Pointer at: 81b77f98
Now running in RAM - U-Boot at: 81bc8000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed address
eth0: 00:03:7f:09:0b:ad
eth0 up
No valid address in Flash. Using fixed address
eth1: 00:03:7f:09:0b:ad
eth1 up
eth0, eth1
Press CTRL+C to stop autoboot:  1  0
## Booting image at bf040000 ...
   Image Name:   MIPS Linux Kernel Image
   Created:      2011-12-07   6:12:41 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    950515 Bytes = 928.2 kB
   Load Address: 80002000
   Entry Point:  801f6bd0
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 801f6bd0) ...
## Giving linux memsize in bytes, 33554432

Starting kernel ...

[    0.000000] Linux version 2.6.34.10-svn17952 (root@dd-wrt) (gcc version 4.5.4 20110526 (prerelease) (Linaro GCC 4.5-2011.06-0) ) #9507 Wed Dec 7 07:07:04 CET 2011
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] booting platform Atheros AR7161 rev 2 (0xaa)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 29480k/32768k available (2028k kernel code, 3288k reserved, 503k data, 144k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] irq init done
[    0.000000] plat_time_init: plat time init done
[    0.000000] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[    0.250000] Mount-cache hash table entries: 512
[    0.250000] NET: Registered protocol family 16
[    3.250000] registering PCI controller with io_map_base unset
[    3.260000] bio: create slab <bio-0> at 0
[    3.290000] found calibration data for slot 0 on 0xBF7F1000
[    3.300000] PCI: fixup device 0000:00:00.0
[    3.330000] found calibration data for slot 1 on 0xBF7F5000
[    3.340000] PCI: fixup device 0000:00:01.0
[    3.350000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[    3.350000] pci 0000:00:00.0: BAR 0: set to [mem 0x10000000-0x1000ffff] (PCI address [0x10000000-0x1000ffff]
[    3.360000] pci 0000:00:01.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
[    3.360000] pci 0000:00:01.0: BAR 0: set to [mem 0x10010000-0x1001ffff] (PCI address [0x10010000-0x1001ffff]
[    3.370000] fixup irq: got 48
[    3.370000] fixup irq: got 49
[    3.370000] Switching to clocksource MIPS
[    3.380000] NET: Registered protocol family 2
[    3.380000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    3.390000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    3.400000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    3.400000] TCP: Hash tables configured (established 1024 bind 1024)
[    3.410000] TCP reno registered
[    3.410000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    3.420000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    3.420000] NET: Registered protocol family 1
[    3.430000] gpio_proc: module loaded and /proc/gpio/ created
[    3.430000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
[    3.440000] AR7100 GPIOC major 0
[    3.440000] init_vdso successfull
[    3.450000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[    3.450000] msgmni has been set to 57
[    3.460000] io scheduler noop registered
[    3.460000] io scheduler deadline registered (default)
[    3.470000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    3.480000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
[    3.480000] console [ttyS0] enabled, bootconsole disabled
[    3.480000] console [ttyS0] enabled, bootconsole disabled
[    3.500000] guessed flashsize = 8M
[    3.500000] scanning for root partition
[    3.500000] uboot detected
[    3.510000] bootloader size = 40000
[    3.510000]
[    3.510000] found squashfs at 129000
[    3.520000] Creating 8 MTD partitions on "ar7100-nor0":
[    3.520000] 0x000000000000-0x000000040000 : "RedBoot"
[    3.530000] 0x000000040000-0x000000800000 : "linux"
[    3.540000] 0x000000129000-0x000000660000 : "rootfs"
[    3.540000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    3.550000] mtd: partition "rootfs" set to be root filesystem
[    3.560000] 0x000000660000-0x0000007e0000 : "ddwrt"
[    3.570000] 0x0000007e0000-0x0000007f0000 : "nvram"
[    3.570000] 0x0000007f0000-0x000000800000 : "FIS directory"
[    3.580000] 0x0000007f0000-0x000000800000 : "board_config"
[    3.580000] 0x000000000000-0x000000800000 : "fullflash"
[    3.590000] PPP generic driver version 2.4.2
[    3.590000] PPP Deflate Compression module registered
[    3.600000] PPP BSD Compression module registered
[    3.600000] PPP MPPE Compression module registered
[    3.610000] NET: Registered protocol family 24
[    3.610000] PPPoL2TP kernel driver, V1.0
[    3.620000] IMQ driver loaded successfully.
[    3.620000]    Hooking IMQ before NAT on PREROUTING.
[    3.630000]    Hooking IMQ after NAT on POSTROUTING.
[    3.630000] tun: Universal TUN/TAP device driver, 1.6
[    3.640000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    4.040000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
[    4.070000] u32 classifier
[    4.070000]     input device check on
[    4.080000]     Actions configured
[    4.080000] Netfilter messages via NETLINK v0.30.
[    4.080000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
[    4.090000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[    4.100000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[    4.110000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[    4.110000] nf_conntrack_rtsp v0.6.21 loading
[    4.120000] nf_nat_rtsp v0.6.21 loading
[    4.120000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    4.130000] IPP2P v0.8.2 loading
[    4.130000] TCP westwood registered
[    4.130000] TCP hybla registered
[    4.140000] TCP vegas registered
[    4.140000] NET: Registered protocol family 17
[    4.140000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    4.150000] All bugs added by David S. Miller <davem@redhat.com>
[    4.190000] Broken NVRAM found, recovering it (Magic FFFFFFFF)
[    4.200000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    4.200000] Freeing unused kernel memory: 144k freed
start service
starting Architecture code for wrt400
starting hotplug
Jan  1 00:00:05 udevtrigger[251]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory

done
load ATH Ethernet Driver
insmod: ag7100_mod.ko: module not found
[    7.170000] Writing 4
[    8.180000] Writing 6
load ATH 802.11 a/b/g Driver
insmod: ath_hal.ko: module not found
insmod: ath_pci.ko: module not found
insmod: ath_ahb.ko: module not found
load ATH9K 802.11n Driver
[    8.300000] Compat-wireless backport release: compat-wireless-2011-11-08-1-g4ab9b62
[    8.310000] Backport based on wireless-testing.git master-2011-11-15
insmod: compat_firmware_class.ko: module not found
[    8.500000] cfg80211: Calling CRDA to update world regulatory domain
[    8.600000] cfg80211: World regulatory domain updated:
[    8.610000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.620000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.620000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.630000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.640000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.650000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.260000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=48
[    9.270000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[    9.310000] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0010000, irq=49
/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
ath9k deconfigure_single: phy0 ath0
ath9k deconfigure_single: phy1 ath1
[   11.430000] device br0 entered promiscuous mode
killall: ead: no process killed
[   11.470000] ag7100_ring_free Freeing at 0x8197d000
[   11.470000] ag7100_ring_free Freeing at 0x81ae1000
[   12.490000] Writing 4
[   12.500000] ag7100_ring_free Freeing at 0x81ae1000
[   12.500000] ag7100_ring_free Freeing at 0x8197d000
[   13.520000] Writing 4
[   13.530000] device eth0 entered promiscuous mode
/bin/sh: ead: not found[   13.540000] device br0 left promiscuous mode

[   13.550000] device br0 entered promiscuous mode
[   13.560000] device br0 left promiscuous mode
[   13.560000] device br0 entered promiscuous mode
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ath9k deconfigure_single: phy0 ath0
ath9k deconfigure_single: phy1 ath1
/bin/sh: can't create /proc/sys/dev/wifi0/superchannel: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/regdomain: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/countrycode: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/outdoor: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/antennagain: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/antennagainsub: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/channelbw: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/channelshift: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi1/superchannel: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi1/regdomain: nonex[   13.660000] cfg80211: Calling CRDA for country: US
istent directory
/bin/sh: can't create /proc/sys/dev/wifi1/countrycode: nonexistent directory
/bin/sh: can't create /proc/sys/[   13.680000] cfg80211: Regulatory domain changed to country: US
dev/wifi1/outdoo[   13.680000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
r: nonexistent d[   13.690000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
irectory
/bin/s[   13.700000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
h: can't create [   13.710000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
/proc/sys/dev/wi[   13.720000] cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
fi1/antennagain:[   13.730000] cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 nonexistent dir[   13.740000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
ectory
/bin/sh: can't create /proc/sys/dev/wifi1/antennagainsub: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi1/channelbw: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi1/channelshift: nonexistent directory
ath9k configure_single: phy0 ath0
call mac80211autochannel for interface: ath0
þ


at this point it starts over and outputs the very same thing.

P.S. this is not my main router or my only router.

Note: Recoverable via http://infodepot.wikia.com/wiki/Linksys_WRT400N_v1.0#Serial_Recovery

_________________
Peacock Thread-FAQ -- Firmware Recommendations -- dd-wrt Wiki

Testing Multiple Routers -- Bootloader Collection Project -- My Wiki


Last edited by Dark_Shadow on Tue Dec 20, 2011 18:57; edited 4 times in total
Sponsor
Dark_Shadow
DD-WRT Guru


Joined: 31 Aug 2009
Posts: 2430
Location: Third Rock from the Sun

PostPosted: Fri Dec 09, 2011 13:08    Post subject: Reply with quote
Recoverable via http://infodepot.wikia.com/wiki/Linksys_WRT400N_v1.0#Serial_Recovery


Broke boot and started TFTPD tryed to upload both dd-wrt files and OEM bin. I get

ar7100> tftpd
TFTP Server IP is : 192.168.1.1
Load address: 0x80000000
WRequest from 192.168.1.10: [t400n-firmware.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [t400n-firmware.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [t400n-firmware.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [t400n-firmware.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [nksys-to-ddwrt-firmware.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [nksys-to-ddwrt-firmware.bin], [octet]
Error: invalid packet format
Abort
ar7100> tftpd
TFTP Server IP is : 192.168.1.1
Load address: 0x80000000
WRequest from 192.168.1.10: [T400N_1.0.01.19_US_20081224.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [T400N_1.0.01.19_US_20081224.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [T400N_1.0.01.19_US_20081224.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [T400N_1.0.01.19_US_20081224.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [T400N_1.0.01.19_US_20081224.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [T400N_1.0.01.19_US_20081224.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [T400N_1.0.01.19_US_20081224.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [T400N_1.0.01.19_US_20081224.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [T400N_1.0.01.19_US_20081224.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [T400N_1.0.01.19_US_20081224.bin], [octet]
Error: invalid packet formatWRequest from 192.168.1.10: [T400N_1.0.01.19_US_20081224.bin], [octet]
Error: invalid packet format
Abort

_________________
Peacock Thread-FAQ -- Firmware Recommendations -- dd-wrt Wiki

Testing Multiple Routers -- Bootloader Collection Project -- My Wiki


Last edited by Dark_Shadow on Fri Dec 09, 2011 16:09; edited 1 time in total
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7072

PostPosted: Fri Dec 09, 2011 14:01    Post subject: Re: BS 17967 flash WRT400N now stuck in boot loop Reply with quote
Dark_Shadow wrote:
I have bricked and unbricked many broadcom units, but never an atheros.


My skype logs tells me you have Very Happy
There should be debrick instructions at infodepot for the WRT400N..

_________________
I'm on a whiskey diet, lost 3 days already
Dark_Shadow
DD-WRT Guru


Joined: 31 Aug 2009
Posts: 2430
Location: Third Rock from the Sun

PostPosted: Fri Dec 09, 2011 14:47    Post subject: Re: BS 17967 flash WRT400N now stuck in boot loop Reply with quote
LOM wrote:
Dark_Shadow wrote:
I have bricked and unbricked many broadcom units, but never an atheros.


My skype logs tells me you have Very Happy
There should be debrick instructions at infodepot for the WRT400N..
Why would I look on my own wiki? LOL

what routers does your skype log say?

_________________
Peacock Thread-FAQ -- Firmware Recommendations -- dd-wrt Wiki

Testing Multiple Routers -- Bootloader Collection Project -- My Wiki
Dark_Shadow
DD-WRT Guru


Joined: 31 Aug 2009
Posts: 2430
Location: Third Rock from the Sun

PostPosted: Fri Dec 09, 2011 14:50    Post subject: Reply with quote
Nevermind, I feel real stupid Embarassed
_________________
Peacock Thread-FAQ -- Firmware Recommendations -- dd-wrt Wiki

Testing Multiple Routers -- Bootloader Collection Project -- My Wiki
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7072

PostPosted: Fri Dec 09, 2011 15:17    Post subject: Reply with quote
Dark_Shadow wrote:
Nevermind, I feel real stupid Embarassed


Don't, we all have those Alzheimer moments.
Got it running?

_________________
I'm on a whiskey diet, lost 3 days already
Dark_Shadow
DD-WRT Guru


Joined: 31 Aug 2009
Posts: 2430
Location: Third Rock from the Sun

PostPosted: Fri Dec 09, 2011 15:41    Post subject: Reply with quote
LOM wrote:
Dark_Shadow wrote:
Nevermind, I feel real stupid Embarassed


Don't, we all have those Alzheimer moments.
Got it running?
I can get it back to 17201, but if I load anything higher I get the loop boot. Seams to get stuck at call mac80211autochannel for interface: ath0 and rebooting.

Is there any other data I can provide so the problem with the firmware can be found?

_________________
Peacock Thread-FAQ -- Firmware Recommendations -- dd-wrt Wiki

Testing Multiple Routers -- Bootloader Collection Project -- My Wiki
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17417
Location: Hesse/Germany

PostPosted: Fri Dec 09, 2011 19:42    Post subject: Reply with quote
prob forwarded

next time would be nice if u could create a ticket Smile

_________________
GEGEN die EEG-UMLAGE auf EIGENVERBRAUCH!
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
Dark_Shadow
DD-WRT Guru


Joined: 31 Aug 2009
Posts: 2430
Location: Third Rock from the Sun

PostPosted: Fri Dec 09, 2011 20:04    Post subject: Reply with quote
Sash wrote:
prob forwarded

next time would be nice if u could create a ticket Smile
I get confused sometime. If I create a ticket I get "discuss in forums" and when I start a thread.... Well you get the picture.Very Happy


Ticket created http://svn.dd-wrt.com:8000/ticket/2290

_________________
Peacock Thread-FAQ -- Firmware Recommendations -- dd-wrt Wiki

Testing Multiple Routers -- Bootloader Collection Project -- My Wiki
cityismine
DD-WRT Novice


Joined: 09 Feb 2007
Posts: 25

PostPosted: Sun Dec 11, 2011 8:16    Post subject: Reply with quote
I hastily installed r17990 and ended with a bricked unit as well. Can I use tftp method to recover, or will I have to purchase a jtag or serial cable?
Dark_Shadow
DD-WRT Guru


Joined: 31 Aug 2009
Posts: 2430
Location: Third Rock from the Sun

PostPosted: Sun Dec 11, 2011 9:31    Post subject: Reply with quote
cityismine wrote:
I hastily installed r17990 and ended with a bricked unit as well. Can I use tftp method to recover, or will I have to purchase a jtag or serial cable?
You can try, mine wouldn't do it. I had to use a serial TTL convertor and recover via the link I posted.
_________________
Peacock Thread-FAQ -- Firmware Recommendations -- dd-wrt Wiki

Testing Multiple Routers -- Bootloader Collection Project -- My Wiki
Dark_Shadow
DD-WRT Guru


Joined: 31 Aug 2009
Posts: 2430
Location: Third Rock from the Sun

PostPosted: Mon Dec 12, 2011 15:23    Post subject: Reply with quote
@ BrainSlayer

Any word on a test build to test booting problems?

_________________
Peacock Thread-FAQ -- Firmware Recommendations -- dd-wrt Wiki

Testing Multiple Routers -- Bootloader Collection Project -- My Wiki
Dark_Shadow
DD-WRT Guru


Joined: 31 Aug 2009
Posts: 2430
Location: Third Rock from the Sun

PostPosted: Mon Dec 12, 2011 18:34    Post subject: Reply with quote
flashing 18000 results

uploading [6410317]
[ 3083.730000] SQUASHFS error: lzma returned unexpected result 0x1
[ 3083.730000] SQUASHFS error: Unable to read page, block fdb8a, size a87c
[ 3083.790000] SQUASHFS error: lzma returned unexpected result 0x2
[ 3083.800000] SQUASHFS error: Unable to read fragment cache block [291822]
[ 3083.800000] SQUASHFS error: Unable to read page, block 291822, size 9254
[ 3083.810000] SQUASHFS error: lzma returned unexpected result 0x2
[ 3083.820000] SQUASHFS error: Unable to read fragment cache block [291822]
[ 3083.820000] SQUASHFS error: Unable to read page, block 291822, size 9254
[ 3083.830000] SQUASHFS error: lzma returned unexpected result 0x2
[ 3083.840000] SQUASHFS error: Unable to read fragment cache block [291822]
[ 3083.840000] SQUASHFS error: Unable to read page, block 291822, size 9254

Amber SES flashing, No GUI

at this point a power cycle results in boot problem. recoverable via serial.

_________________
Peacock Thread-FAQ -- Firmware Recommendations -- dd-wrt Wiki

Testing Multiple Routers -- Bootloader Collection Project -- My Wiki
Dark_Shadow
DD-WRT Guru


Joined: 31 Aug 2009
Posts: 2430
Location: Third Rock from the Sun

PostPosted: Tue Dec 13, 2011 16:29    Post subject: Reply with quote
Dark_Shadow wrote:
flashing 18000 results

uploading [6410317]
[ 3083.730000] SQUASHFS error: lzma returned unexpected result 0x1
[ 3083.730000] SQUASHFS error: Unable to read page, block fdb8a, size a87c
[ 3083.790000] SQUASHFS error: lzma returned unexpected result 0x2
[ 3083.800000] SQUASHFS error: Unable to read fragment cache block [291822]
[ 3083.800000] SQUASHFS error: Unable to read page, block 291822, size 9254
[ 3083.810000] SQUASHFS error: lzma returned unexpected result 0x2
[ 3083.820000] SQUASHFS error: Unable to read fragment cache block [291822]
[ 3083.820000] SQUASHFS error: Unable to read page, block 291822, size 9254
[ 3083.830000] SQUASHFS error: lzma returned unexpected result 0x2
[ 3083.840000] SQUASHFS error: Unable to read fragment cache block [291822]
[ 3083.840000] SQUASHFS error: Unable to read page, block 291822, size 9254

Amber SES flashing, No GUI

at this point a power cycle results in boot problem. recoverable via serial.


@ BrainSlayer

I see you posted a fix for the lzma error, Could I get a test build for the WRT400N to see if it fixes that as well?

_________________
Peacock Thread-FAQ -- Firmware Recommendations -- dd-wrt Wiki

Testing Multiple Routers -- Bootloader Collection Project -- My Wiki
Dark_Shadow
DD-WRT Guru


Joined: 31 Aug 2009
Posts: 2430
Location: Third Rock from the Sun

PostPosted: Wed Dec 14, 2011 23:49    Post subject: Reply with quote
18007 Results in same simi-bricked state. It's still recoverable.
_________________
Peacock Thread-FAQ -- Firmware Recommendations -- dd-wrt Wiki

Testing Multiple Routers -- Bootloader Collection Project -- My Wiki
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum