Posted: Fri Jan 06, 2012 6:54 Post subject: EOC-5611 :FAIL:
Hello all. I cannot get my 5611 to load. I have tried a couple different ways, used the 12533 version, tried fs init -f as suggested by sash in another post.
I get to the end and do reset, but it never comes back up. I give it five minutes each time, then power it down, and wait another five minutes.
Code:
== Executing boot script in 1.990 seconds - enter ^C to abort
^C
RedBoot> ip_address -l 192.168.1.1 -h 192.168.1.11
IP: 192.168.1.1/255.255.255.0, Gateway: 192.168.21.1
Default server: 192.168.1.11
RedBoot> fis init
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
... Erase from 0xbe7e0000-0xbe7f0000: .
... Program from 0x81fe0400-0x81ff0400 at 0xbe7e0000: .
RedBoot> load -r -b 0x80041000 linux.bin
In this set from the EOC-5610 linux.bin download, it does absolutely nothing. The next paste is with the 12533 version.
Code:
^C== Executing boot script in 0.320 seconds - enter ^C to abort
^C
RedBoot> ip_address -l 192.168.1.1 -h 192.168.1.11
^C
RedBoot> IP: 192.168.1.1/255.255.255.0, Gateway: 192.168.21.1
Default server: 192.168.1.11
RedBoot> fis init
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
... Erase from 0xbe7e0000-0xbe7f0000: .
... Program from 0x81fe0400-0x81ff0400 at 0xbe7e0000: .
RedBoot> load -r -b 0x80041000 linux2.bin
Using default protocol (TFTP)
Raw file loaded 0x80041000-0x8054afff, assumed entry at 0x80041000
RedBoot> fis create linux
... Erase from 0xbe030000-0xbe53a000: .................................................................................
... Program from 0x80041000-0x8054b000 at 0xbe030000: .................................................................................
... Erase from 0xbe7e0000-0xbe7f0000: .
... Program from 0x81fe0400-0x81ff0400 at 0xbe7e0000: .
RedBoot> fconfig boot_script true
boot_script: Setting to true
RedBoot> fconfig boot_script_timeout 4
boot_script_timeout: Setting to 4
Update RedBoot non-volatile configuration - continue (y/n)? y
... Erase from 0xbe7e0000-0xbe7f0000: .
... Program from 0x81fe0400-0x81ff0400 at 0xbe7e0000: .
RedBoot> fconfig
Run script at boot: true
Boot script:
.. fis load -l linux
.. exec
Enter script, terminate with empty line
>> fis load -l linux
>> exec
>>
Boot script timeout (1000ms resolution): 4
Use BOOTP for network configuration: false
Gateway IP address: 192.168.21.1
Local IP address: 192.168.1.1
Local IP address mask: 255.255.255.0
Default server IP address:
Console baud rate: 9600
GDB connection port: 9000
Force console for special debug messages: false
Network debug at boot time: false
Update RedBoot non-volatile configuration - continue (y/n)? y
... Erase from 0xbe7e0000-0xbe7f0000: .
... Program from 0x81fe0400-0x81ff0400 at 0xbe7e0000: .
RedBoot> reset
Can't say I haven't tried and read other topics...
Code:
RedBoot> fis load -l linux
Image loaded from 0x80041000-0x802d4a2c
RedBoot> exec