go back to the state where you have dd-wrt with wrong mac on the router.
cut off the Netgear header from stock firmware so it starts with HDR0 and update with that file in the dd-wrt gui. _________________ Kernel panic: Aiee, killing interrupt handler!
Joined: 31 Aug 2009 Posts: 2448 Location: Third Rock from the Sun
Posted: Fri Jan 13, 2012 16:08 Post subject:
LOM wrote:
well, then go for plan B
no good
Code:
upgrade_ver[v24.0.0] upgrade_ver[240000] intel_ver[14108] 4712_ver[15000]
function stop_snmp not found
function stop_pppoeserver not found
function stop_olsrd not found
function stop_openvpn not found
function stop_openvpnserver not found
function stop_freeradius not found
freeram=[14524416] bufferram=[1331200]
The free memory is enough, writing image once.
write=[3444736]
linux: CRC OK44785]
Writing image to flash, waiting a moment...
write block [0] at [0x00000000]
write block [65536] at [0x00010000]
write block [131072] at [0x00020000]
write block [196608] at [0x00030000]
write block [262144] at [0x00040000]
write block [327680] at [0x00050000]
write block [393216] at [0x00060000]
write block [458752] at [0x00070000]
write block [524288] at [0x00080000]
write block [589824] at [0x00090000]
write block [655360] at [0x000A0000]
write block [720896] at [0x000B0000]
write block [786432] at [0x000C0000]
write block [851968] at [0x000D0000]
write block [917504] at [0x000E0000]
write block [983040] at [0x000F0000]
write block [1048576] at [0x00100000]
write block [1114112] at [0x00110000]
write block [1179648] at [0x00120000]
write block [1245184] at [0x00130000]
write block [1310720] at [0x00140000]
write block [1376256] at [0x00150000]
write block [1441792] at [0x00160000]
write block [1507328] at [0x00170000]
write block [1572864] at [0x00180000]
write block [1638400] at [0x00190000]
write block [1703936] at [0x001A0000]
write block [1769472] at [0x001B0000]
write block [1835008] at [0x001C0000]
write block [1900544] at [0x001D0000]
write block [1966080] at [0x001E0000]
write block [2031616] at [0x001F0000]
write block [2097152] at [0x00200000]
write block [2162688] at [0x00210000]
write block [2228224] at [0x00220000]
write block [2293760] at [0x00230000]
write block [2359296] at [0x00240000]
write block [2424832] at [0x00250000]
write block [2490368] at [0x00260000]
write block [2555904] at [0x00270000]
write block [2621440] at [0x00280000]
write block [2686976] at [0x00290000]
write block [2752512] at [0x002A0000]
write block [2818048] at [0x002B0000]
write block [2883584] at [0x002C0000]
write block [2949120] at [0x002D0000]
write block [3014656] at [0x002E0000]
write block [3080192] at [0x002F0000]
write block [3145728] at [0x00300000]
write block [3211264] at [0x00310000]
write block [3276800] at [0x00320000]
write block [3342336] at [0x00330000]
write block [3407872] at [0x00340000]
Write fake len/chksum @ 0x3AFFF8 ...done.
uploading [3444785]
BCMDOG: WDT device closed unexpectedly. WDT will not stop!
Restarting system.
Please stand by while rebooting the system...
Decompressing..........done
CFE for WNR3500v2 version: v1.0.29
Build Date: Fri Jun 12 11:11:15 CST 2009
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found a 4MB ST compatible serial flash
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.28
CPU type 0x19740: 453MHz
Tot mem: 32768 KBytes
Device eth0: hwaddr C0-3F-0E-AB-EC-84, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Loader:raw Filesys:tftp Dev:eth0 File:192.168.1.2:vmlinuz Options:(null)
Loading: Failed.
Could not load 192.168.1.2:vmlinuz: Timeout occured
Checksum mismatch:
Image chksum: 0x00000000
Calc chksum: 0x02C0010E
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: . 0 bytes read
Failed.
Could not load flash0.os:: Error
Start TFTP server
Reading ::
Strange.. I know that cfe 1.29 is buggy and there should be a thread about it in myopenwrtrouter, I think they replaced it with an older version.
Plan C
Load the stock firmware in the same way and with the same switches as when you loaded dd-wrt. Make sure the header in the stock is of the same kind as in the header in dd-wrt.
You need to get stock firmware onto the router in some way before converting to dd-wrt. _________________ Kernel panic: Aiee, killing interrupt handler!
Joined: 31 Aug 2009 Posts: 2448 Location: Third Rock from the Sun
Posted: Fri Jan 13, 2012 16:57 Post subject:
fggs wrote:
LOM, isn't checksum the culprit here? I think whenever he gets a valid checksum it will work..
no, getting dd-wrt on here the checksums are off too.
LOM wrote:
Strange.. I know that cfe 1.29 is buggy and there should be a thread about it in myopenwrtrouter, I think they replaced it with an older version.
Plan C
Load the stock firmware in the same way and with the same switches as when you loaded dd-wrt. Make sure the header in the stock is of the same kind as in the header in dd-wrt.
You need to get stock firmware onto the router in some way before converting to dd-wrt.
will try, i erase everything before HDR0 on both dd-wrt.v24-17084_NEWD-2_K2.6_mini-WNR3500v2.chk and WNR3500v2-V1.2.2.28_25.0.85NA.chk. But I will recheck both files to make sure. _________________ Peacock Thread-FAQ -- dd-wrt Wiki
Joined: 31 Aug 2009 Posts: 2448 Location: Third Rock from the Sun
Posted: Fri Jan 13, 2012 17:48 Post subject:
did a search on myopenrouter forums for 3500v2 and it only came up with threads for 3500L and 3500L v2 _________________ Peacock Thread-FAQ -- dd-wrt Wiki
See what tsanga did with the help of LOM, of course!
Good find I had looked at that thread before at the recomedation of LOM but only for the board_data file. After you reposted the link this is what happened.
In WNR3500v2-V1.2.2.28_25.0.85NA.chk I changed the header info from "U12H127T00_NETGEAR" to "U12H127T70_NETGEAR" and uploaded the file to the waiting "Reading ::". It took it and ran with it.
At this point I had OEM firmware running back on it. So I checked all the MAC's in the OEM firmware to make sure they were correct. They were.
Then loaded from the OEM GUI dd-wrt.v24-18024_NEWD-2_K2.6_mini-WNR3500v2.chk. to my amazement it loade fine. Changed the password, then checked the system info and wouldn't ya know it, all the MAC's were correct.
BIG thanks to fggs for pointing out that link again.
Even BIGGER thanks to LOM for participating in the OP.
As a side note: I don't know if this unit is yours or from someone, but you do realise that by editing the FIRMWARE, board_data remains unfixed. Which means, if one day you or the person wants to revert, will need this stock firmware you edited.
Joined: 31 Aug 2009 Posts: 2448 Location: Third Rock from the Sun
Posted: Fri Jan 13, 2012 18:50 Post subject:
fggs wrote:
Thanks! Glad I could help.
As a side note: I don't know if this unit is yours or from someone, but you do realise that by editing the FIRMWARE, board_data remains unfixed. Which means, if one day you or the person wants to revert, will need this stock firmware you edited.
Oh I guess I should have tryed to load the unedited image?
Or does the board data need to be changed to "U12H127T00_NETGEAR" _________________ Peacock Thread-FAQ -- dd-wrt Wiki