TENDA W311R - Bad flash recover and Install dd-wrt firmware!

Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware
Goto page Previous  1, 2, 3 ... 17, 18, 19 ... 21, 22, 23  Next
Author Message
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Fri Jan 27, 2012 20:22    Post subject: Reply with quote
kapastratos wrote:
Without a serial console, you can`t do anything about it.

so this is what you have to do:

1 - clean the board with some alcohol
2 - make a good quality photo
3 - upload it here

I wanna see how bad is it and if it can be fixed.

OK, tomorrow I will upload photo
Sponsor
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sat Jan 28, 2012 11:24    Post subject: Reply with quote
TendaW311R+ wrote:
kapastratos wrote:
Without a serial console, you can`t do anything about it.

so this is what you have to do:

1 - clean the board with some alcohol
2 - make a good quality photo
3 - upload it here

I wanna see how bad is it and if it can be fixed.

OK, tomorrow I will upload photo

Hi again. this is damage part. Please see it. Is there any way to repair it ? Thanks
kapastratos
DD-WRT Novice


Joined: 04 Oct 2008
Posts: 33
Location: Romania

PostPosted: Sat Jan 28, 2012 12:22    Post subject: Reply with quote
this is the best picture that you were able to make? please make a good quality picture, this is a bad picture and I am unable to see the traces...
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sat Jan 28, 2012 12:24    Post subject: Reply with quote
kapastratos wrote:
this is the best picture that you were able to make? please make a good quality picture, this is a bad picture and I am unable to see the traces...

OK, but I am going to make it, after one hour.
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sat Jan 28, 2012 13:05    Post subject: Reply with quote
TendaW311R+ wrote:
kapastratos wrote:
this is the best picture that you were able to make? please make a good quality picture, this is a bad picture and I am unable to see the traces...

OK, but I am going to make it, after one hour.

This is the best picture, that I can do
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sat Jan 28, 2012 16:54    Post subject: Reply with quote
Please help me
kapastratos
DD-WRT Novice


Joined: 04 Oct 2008
Posts: 33
Location: Romania

PostPosted: Sat Jan 28, 2012 17:32    Post subject: Reply with quote
OK, I did a high quality photo of my router, and this is what you have to do:

- Scratch the red points (you need a magnifier)
- Solder 2 wires with a 15W soldering iron...more than that and you will deteriorate the pcb (you need a magnifier)
- Check the wiring to avoid doing any bridges.
- Follow my first post and you will be able to recover your router.

Good luck.
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sat Jan 28, 2012 18:28    Post subject: Reply with quote
This is my motherboard. Please see it and tell me may I solder on RX. Is there any other pins, when I can solder on RX. Thanks for all help and picture too
kapastratos
DD-WRT Novice


Joined: 04 Oct 2008
Posts: 33
Location: Romania

PostPosted: Sat Jan 28, 2012 18:53    Post subject: Reply with quote
dude, do you see the picture that I posted? I already told you where to solder. good luck
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sat Jan 28, 2012 18:55    Post subject: Reply with quote
kapastratos wrote:
dude, do you see the picture that I posted? I already told you where to solder. good luck

Put my RX is damage ( that you show in your picture ). So this is the end of the router, right ?
kapastratos
DD-WRT Novice


Joined: 04 Oct 2008
Posts: 33
Location: Romania

PostPosted: Sat Jan 28, 2012 19:02    Post subject: Reply with quote
I don`t see from your picture, I think you can solder there...that`s why I told you to send me a good quality picture...not a zoomed one!
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sat Jan 28, 2012 19:12    Post subject: Reply with quote
May be this one is good. If it is not. Sorry for that
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sat Jan 28, 2012 19:15    Post subject: Reply with quote
Are there any other pins for TX, RX ?
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sat Jan 28, 2012 19:28    Post subject: Reply with quote
TendaW311R+ wrote:
Are there any other pins for TX, RX ?

tomorrow I will try with better picture and will post it here Wink
kapastratos
DD-WRT Novice


Joined: 04 Oct 2008
Posts: 33
Location: Romania

PostPosted: Sat Jan 28, 2012 20:16    Post subject: Reply with quote
no, there are no other pins, they go directly to the CPU!
Goto page Previous  1, 2, 3 ... 17, 18, 19 ... 21, 22, 23  Next Display posts from previous:    Page 18 of 23
Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum