Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Mon Mar 19, 2012 2:29 Post subject:
Oleg_Andreych wrote:
Doh, still no wi-fi on my dir-825 (not 2.4 nor 5 GHz).
will never be back again until you fix your calibration data which seems to be destroyed on your device. thats the only reason if the wifi is not working. you can see that in the kernel log too _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Mon Mar 19, 2012 2:30 Post subject:
steinwedel wrote:
Webflash on Buffalo WBMR-HP-G300H works ok.
Internet connection via internal modem works. Lan also ok. Airprint works.
Tx power can't be set. Changes are neglected. Airprint via vpn doesn't work.
No other problems so far. Development of firmware is on a good way. A good idea is in my opinion to change under WAN Connection Type, Advanced settings, Payload type the default setting to Bridged.
tx power setting works as always. but dont expect that values are accepted which are invalid/too high/unsupported by the wireless card _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Mon Mar 19, 2012 2:43 Post subject:
would be good. i dont have a wndr3800, but it should be compatible _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Webflash on Buffalo WBMR-HP-G300H works ok.
Internet connection via internal modem works. Lan also ok. Airprint works.
Tx power can't be set. Changes are neglected. Airprint via vpn doesn't work.
No other problems so far. Development of firmware is on a good way. A good idea is in my opinion to change under WAN Connection Type, Advanced settings, Payload type the default setting to Bridged.
tx power setting works as always. but dont expect that values are accepted which are invalid/too high/unsupported by the wireless card
Your are right. Didn't expect, that default power is max allowed power. The web interface seen to accept higher values. Would it be possible to save only allowed values so you notice wrong values on entering data?
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Mon Mar 19, 2012 7:01 Post subject:
TX power may be working fine, but TX chains are not, at least for WNDR3700 v1 and DIR-825 units and probably similar ones, r18024 is the last one with proper TX chains.
r18007 = max TX power 20 dBm, GUI TX 300, GUI RX 300, throughput >110 Mbps
r18024 = max TX power 20 dBm, GUI TX 300, GUI RX 300, throughput >110 Mbps
r18687 = max TX power 17 dBm, GUI TX 150 GUI RX 300, throughput <85 Mbps
r18740 = max TX power 17 dBm, GUI TX 150 GUI RX 300, throughput <85 Mbps
r18767 = max TX power 17 dBm, GUI TX 150 GUI RX 300, throughput <85 Mbps
3 dBm less TX power is half the power + throughput drop. Points to a TX problem. N-Only mode for ath0 also breaks for 2x2 clients starting at r18687, they don't connect at all. With r18007/r18024 I have to set TX chain to 1 to copy the performance of r18687+ at 1+2. Already a ticket up for this. _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
Posted: Mon Mar 19, 2012 12:53 Post subject: Re: No 5GHz Band DIR 825 RevB
grantk wrote:
5GHz band (ath1 interface) on DIR 825 Rev B is not working for me.
Status page says the radio is on, but it doesn't appear to pick a channel on "Auto" channel mode. If I manually try to set the channel, it still doesn't work. The "Channel" parameter just displays "Unknown" all the time. Build 18024 works fine.
*** The same device and the same problem, more than that , VAP's not working also.
- - - When it's just after a hard reset well then every wireless connection's working, but as soon as 2.4 Ghz 's connected (blue INTERNET LED's lighted and i can see a connected devices from each side) as "CLIENT BRIDGE" so after that 5 Ghz and VAPs aren't working if even if enabled...
Posted: Mon Mar 19, 2012 12:58 Post subject: wzr-hp-g300nh
flashed my wzr-hp-g300nh yesterday with webflash image
on my router configured as wireless bridge, worked great, but i couldn't get it to receive default gateway via DHCP,
when i set it manually though it worked. haven't tried doing a 30/30/30 yet. since manual config works.
