ZTE MF821D 4G USB modem won't connect in r19342

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Author Message
sick
DD-WRT Novice


Joined: 24 May 2012
Posts: 9

PostPosted: Thu May 24, 2012 15:30    Post subject: ZTE MF821D 4G USB modem won't connect in r19342 Reply with quote
I have a Linksys e4200 and am unable to connect using my MF821D 4G USB Modem.
I tried on both BrainSlayer-V24-preSP2 r18777 & V24-K26 svn18946.
I have also read through and tried as per the following thread http://www.dd-wrt.com/phpBB2/viewtopic.php?p=676542

Any assistance would be greatly appreciated.


Last edited by sick on Tue Jun 12, 2012 10:52; edited 1 time in total
Sponsor
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7647

PostPosted: Thu May 24, 2012 16:01    Post subject: Reply with quote
That thread is a continuation of a previous thread for the stick and there is a link to the previous thread in which you can see what info is required.

You have only provided the model number and that is basically worthless info since there exists so many variants of a certain model number.

Do also read:
www.dd-wrt.com/wiki/index.php/Mobile_Broadband

_________________
Kernel panic: Aiee, killing interrupt handler!
sick
DD-WRT Novice


Joined: 24 May 2012
Posts: 9

PostPosted: Fri May 25, 2012 9:27    Post subject: Reply with quote
cat /proc/bus/usb/devices

T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.24.111 ohci_hcd
S: Product=OHCI Host Controller
S: SerialNumber=0000:00:04.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.24.111 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:04.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=0167 Rev= 0.00
S: Manufacturer=ZTE,Incorporated
S: Product=ZTE LTE Technologies MSM
S: SerialNumber=MF821DTLAS000000
C:* #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms


lsmod

Module Size Used by
option 16384 0
sierra 8192 0
usbserial 24576 2 option,sierra
ohci_hcd 16384 0
uhci_hcd 20480 0
ehci_hcd 28672 0
usbcore 98304 7 option,sierra,usbserial,ohci_hcd,uhci_hcd,ehci_hcd
nls_base 8192 0
switch_robo 4096 0
switch_core 8192 1 switch_robo
bcm57xx 102400 0


dmesg


Linux version 2.6.24.111 (root@dd-wrt) (gcc version 4.1.2) #9581 Mon Mar 19 06:57:10 CET 2012
CPU revision is: 00019740
Found a 16MB ST compatible serial flash
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Entering add_active_range(0, 0, 16384) 0 entries of 256 used
Zone PFN ranges:
Normal 0 -> 16384
HighMem 16384 -> 16384
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 16384
On node 0 totalpages: 16384
Normal zone: 0 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 16384 pages, LIFO batch:3
HighMem zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order. Total pages: 16384
Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM4716 rev 1 at 480 MHz
Using 240.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 58604k/65536k available (3522k kernel code, 6876k reserved, 1373k data, 216k init, 0k highmem)
Calibrating delay loop... 239.20 BogoMIPS (lpj=1196032)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: no core
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.0 to 64
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.1 to 64
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
E4200 GPIO Init
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
et_module_init: passivemode set to 0x0
PCI: Setting latency timer of device 0000:00:02.0 to 64
VID 0 is set in nvram, Ignoring
E4200 switch LEDs fix
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.9
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:01.0 to 64
pflash: found no supported devices
bootloader size: 262144
nvram size: 61440
sflash: Filesystem type: squashfs, size=0x616ad7
partition size = 6426624
Creating 5 MTD partitions on "sflash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x00ff0000 : "linux"
0x0019f000-0x007c0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x00ff0000-0x01000000 : "nvram"
0x007c0000-0x00ff0000 : "ddwrt"
Broadcom Watchdog Timer: 0.07 initialized.
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
decode 1f02
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 216k freed
roboswitch: Probing device eth0: found a 53115!
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB20H mdio control register : 0x8000000c
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB20H mdio control register : 0x8000000c
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
usb usb2: configuration #1 chosen from 1 choice
usb 1-1: new high speed USB device using ehci_hcd and address 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: configuration #1 chosen from 1 choice
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
br0: port 3(eth2) entering learning state
br0: port 2(eth1) entering learning state
br0: port 1(vlan1) entering learning state
device vlan2 entered promiscuous mode
br0: topology change detected, propagating
br0: port 3(eth2) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.7.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
device vlan1 left promiscuous mode
br0: port 1(vlan1) entering disabled state
device eth1 left promiscuous mode
br0: port 2(eth1) entering disabled state
device eth2 left promiscuous mode
br0: port 3(eth2) entering disabled state
device vlan1 entered promiscuous mode
br0: port 1(vlan1) entering learning state
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
device eth2 entered promiscuous mode
br0: port 3(eth2) entering learning state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 3(eth2) entering forwarding state
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7647

PostPosted: Fri May 25, 2012 11:02    Post subject: Reply with quote
sick wrote:

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=0167 Rev= 0.00
S: Manufacturer=ZTE,Incorporated
S: Product=ZTE LTE Technologies MSM
S: SerialNumber=MF821DTLAS000000


See, that was a bit more informative than your previous "It doesn't work" post.

19d2:0167 is also the id of MF820D which I added support for only a few days ago.
The stick should work in the next published public build.

_________________
Kernel panic: Aiee, killing interrupt handler!
sick
DD-WRT Novice


Joined: 24 May 2012
Posts: 9

PostPosted: Fri May 25, 2012 11:52    Post subject: Reply with quote
Great stuff, much appreciated Very Happy
sick
DD-WRT Novice


Joined: 24 May 2012
Posts: 9

PostPosted: Tue May 29, 2012 6:19    Post subject: Reply with quote
Any word on when we could expect the next release?
Tx
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7647

PostPosted: Tue May 29, 2012 7:49    Post subject: Reply with quote
That is something only the developers know.
I only upload 3G modem fixes for them to apply.

_________________
Kernel panic: Aiee, killing interrupt handler!
sick
DD-WRT Novice


Joined: 24 May 2012
Posts: 9

PostPosted: Tue May 29, 2012 17:48    Post subject: Reply with quote
is there perhaps a command I can run to get it to work in the meantime?
sick
DD-WRT Novice


Joined: 24 May 2012
Posts: 9

PostPosted: Tue Jun 12, 2012 10:54    Post subject: Reply with quote
Still not working with new release.
Any assistance would be greatly appreciated.



cat /proc/bus/usb/devices

T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.24.111 ohci_hcd
S: Product=OHCI Host Controller
S: SerialNumber=0000:00:04.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.24.111 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:04.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=0167 Rev= 0.00
S: Manufacturer=ZTE,Incorporated
S: Product=ZTE LTE Technologies MSM
S: SerialNumber=MF821DTLAS000000
C:* #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms


lsmod

Module Size Used by
option 20480 0
usbserial 24576 1 option
ohci_hcd 16384 0
uhci_hcd 20480 0
ehci_hcd 28672 0
usbcore 98304 6 option,usbserial,ohci_hcd,uhci_hcd,ehci_hcd
nls_base 8192 0
switch_robo 4096 0
switch_core 8192 1 switch_robo
bcm57xx 102400 0



dmesg

Linux version 2.6.24.111 (root@dd-wrt) (gcc version 4.1.2) #10759 Fri Jun 8 02:46:04 CEST 2012
CPU revision is: 00019740
Found a 16MB ST compatible serial flash
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Entering add_active_range(0, 0, 16384) 0 entries of 256 used
Zone PFN ranges:
Normal 0 -> 16384
HighMem 16384 -> 16384
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 16384
On node 0 totalpages: 16384
Normal zone: 0 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 16384 pages, LIFO batch:3
HighMem zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order. Total pages: 16384
Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM4716 rev 1 at 480 MHz
Using 240.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 58604k/65536k available (3522k kernel code, 6868k reserved, 1366k data, 216k init, 0k highmem)
Calibrating delay loop... 239.20 BogoMIPS (lpj=1196032)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: no core
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.0 to 64
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.1 to 64
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
E4200 GPIO Init
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = Cool is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
et_module_init: passivemode set to 0x0
PCI: Setting latency timer of device 0000:00:02.0 to 64
VID 0 is set in nvram, Ignoring
E4200 switch LEDs fix
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.9
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:01.0 to 64
pflash: found no supported devices
bootloader size: 262144
nvram size: 61440
sflash: Filesystem type: squashfs, size=0x63f384
partition size = 6558720
Creating 5 MTD partitions on "sflash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x00ff0000 : "linux"
0x0019ec00-0x007e0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x00ff0000-0x01000000 : "nvram"
0x007e0000-0x00ff0000 : "ddwrt"
Broadcom Watchdog Timer: 0.07 initialized.
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
decode 1f02
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 216k freed
roboswitch: Probing device eth0: found a 53115!
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB20H mdio control register : 0x8000000c
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB20H mdio control register : 0x8000000c
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
br0: port 3(eth2) entering learning state
br0: port 2(eth1) entering learning state
br0: port 1(vlan1) entering learning state
device vlan2 entered promiscuous mode
br0: topology change detected, propagating
br0: port 3(eth2) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1.1
device vlan1 left promiscuous mode
br0: port 1(vlan1) entering disabled state
device eth1 left promiscuous mode
br0: port 2(eth1) entering disabled state
device eth2 left promiscuous mode
br0: port 3(eth2) entering disabled state
device vlan1 entered promiscuous mode
br0: port 1(vlan1) entering learning state
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
device eth2 entered promiscuous mode
br0: port 3(eth2) entering learning state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 3(eth2) entering forwarding state
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7647

PostPosted: Tue Jun 12, 2012 11:13    Post subject: Reply with quote
The updated drivers I have submitted has not yet been committed to the source tree. Sad

http://svn.dd-wrt.com:8000/ticket/2556

_________________
Kernel panic: Aiee, killing interrupt handler!
sick
DD-WRT Novice


Joined: 24 May 2012
Posts: 9

PostPosted: Tue Jun 12, 2012 12:27    Post subject: Reply with quote
Is there anyway to get this working manually?
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7647

PostPosted: Tue Jun 12, 2012 15:04    Post subject: Reply with quote
sick wrote:
Is there anyway to get this working manually?


No, it needs driver support.

_________________
Kernel panic: Aiee, killing interrupt handler!
sick
DD-WRT Novice


Joined: 24 May 2012
Posts: 9

PostPosted: Sat Aug 18, 2012 10:47    Post subject: Reply with quote
07-20-12-r19519

Still not working Sad
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7647

PostPosted: Sat Aug 18, 2012 11:16    Post subject: Reply with quote
sick wrote:
07-20-12-r19519

Still not working Sad


Show me the device list again when running r19519.
It should have driver = option instead of driver =none for the first 5 interfaces (0-4) and your dmesg should also show creation of ttyUSB0 to ttyUSB4.

There is from what I can see nothing missing in the source and the stick is now supported in the option driver.

_________________
Kernel panic: Aiee, killing interrupt handler!
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum