Posted: Sat Jun 09, 2012 19:18 Post subject: WDNR3800 OK so far
New router, up from very old DD-WRT and old router. Bought WDNR3800, downgrade to OEM .16 version, upgrade to 19342, no problems at all in process.
Speed testing with NTTTCP, 1 stream, defaults:
- Lan to Lan - 826mbs
- Lan to Wan - 333 mbs
- Lan to wlan (no encrypt) 74 mbs
- Lan to wlan (WPA2/AES) 48mbs
Have used port forwarding both few other features, but so far has not missed a beat. As noted by others graphs look wrong. Inconing logs don't show NAT connections (not sure if they should), but the connection works.
Very nice -- needed a new router in a hurry, was lucky to find a decent speed one with DD-WRT support at a local store. Thank you for doing this.
Flashed successfully on WR1043ND. Unfortunately, the wifi speed is still way lower than on 17201 or stock with my Intel ABGN4965. We're talking about 3~3,5 MB/s whereas 17201 and stock max out at around 10~11 MB/s.
Fiddling with the wifi settings (mixed, NG mixed, N-only, channel width [40 Mhz only is not possible since the 4965AGN accepts 20 Mhz only in 2,4], TX/RX antenna chains, yadda yadda...) makes no difference.
there's something up with this build for me.
flashed from 19327 which worked fine.
at first websites load, then after about 10 minutes it's like dns stops resolving - chrome just hangs. give it a minute or two and everything starts working again, 10 minutes latter everything's hanging again... in fact, it's doing it right now - could be opendns i suppose but this only started happening after flashing this build.
EDIT: must be opendns - set dns entries to ISP, problem solved. _________________ WZR-1750DHP r29607
there's something up with this build for me.
flashed from 19327 which worked fine.
at first websites load, then after about 10 minutes it's like dns stops resolving - chrome just hangs. give it a minute or two and everything starts working again, 10 minutes latter everything's hanging again... in fact, it's doing it right now - could be opendns i suppose but this only started happening after flashing this build.
EDIT: must be opendns - set dns entries to ISP, problem solved.
I switched to Googles DNS for the same reason, OpenDNS was hanging and causing all sorts of page loading errors, some sites refused to load, moved to Googles DNS and everything started working again
Weird because OpenDNS was great for a long time prior _________________ TPLINK TL-WR2543ND (5GHz)
WRT160NL (2.4GHz)
I switched to Googles DNS for the same reason, OpenDNS was hanging and causing all sorts of page loading errors, some sites refused to load, moved to Googles DNS and everything started working again
do you use odns's malware and phishing protection?
i've just logged in to the opendns dashboard and it's reporting blocked malware connection attempts to js.tongji.linezing.com... slightly worrying.
Posted: Sun Jun 10, 2012 16:27 Post subject: in/out security logging not functional?
New (again) to dd-wrt, so maybe I am doing it incorrectly, but I cannot get anything to record in the incoming and outgoing log table.
On this version, with WNDR3800, set to enabled, high, and all three options enabled, then tried to connect via PPTP to debug (PPTP failed, I think it's set up right) and to a forwarded port (succeeded), nothing shows up in either case.
I've seen a couple of comments (on other routers) that some versions do not have logging compiled in - perhaps this version does not. Is there a place I can check to know? Sorry if this is intended behavior.
Buffalo (as a Client router) doesn't get assigned an IP in Wan-DHCP (even when this Client is connected FINE to the main router). (but Status-Wireless show 60% connection-wifi as good as it always was).)
Manually copy down IP and set First drop-down to Static, fill out the blanks. Still no Internet .
No success: r19342 wzr-hp-g300nh-dd-wrt-webupgrade-MULTI
Roll-back and everything's normal:
R16785 wzr-hp-g300nh-dd-wrt-webupgrade-MULTI
Wired LAN is dead here. OS X sees that the ethernet cable is plugged in, but gets do address from router DHCP (eventually self-assigns dummy address). This happened under 19327, persists under 19342 and 18777, across hard resets (30-30-30). grrrrrr
Wireless seems fine.
Anything I can do to attempt to revive gigabit LAN?