D-Link DIR-600 rev B5

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware
Goto page Previous  1, 2, 3, 4, 5  Next
Author Message
ccmuhah
DD-WRT Novice


Joined: 26 Mar 2012
Posts: 3

PostPosted: Thu Apr 05, 2012 12:39    Post subject: Reply with quote
We desperately need DD-WRT on our routers... Crying or Very sad Crying or Very sad Crying or Very sad
Sponsor
iddeenkhai
DD-WRT Novice


Joined: 30 Dec 2009
Posts: 18

PostPosted: Thu Apr 05, 2012 17:28    Post subject: Reply with quote
Just get another router. As I already explained, support for unsupported chipset is even harder to come by.
checho
DD-WRT User


Joined: 27 Feb 2007
Posts: 492
Location: Bulgaria

PostPosted: Sat Jun 16, 2012 9:43    Post subject: Reply with quote
I have read the serial console of that device.

Here is the native firmware booting

Code:
U-Boot 1.1.3 (Feb 25 2011 - 14:31:26) (ALPHA)

SVN revision: 499
Target board: WRG-N49

Board: Ralink APSoC DRAM:  32 MB
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 42
spi device id: ef 40 16 0 0 (40160000)
find flash: W25Q32BV
..============================================
Ralink UBoot Version: 3.5.1.0
--------------------------------------------
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:Feb 25 2011  Time:14:31:26
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
## Powering down port 0 ~ 3.

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
   A: Load  Runtime code then write to Flash via Serial.

You choosed 3

 0
   
3: System Boot system code via Flash.
## Booting image at bc050000 ...
........................................................addr:80400000
We have SEAMA, Image Size = 3559456
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... OK
## Transferring control to Linux (at address ff000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...


LINUX started...

 THIS IS ASIC
is_RT3052 = 0, is_RT3352 = 0
is_RT3350 = 0, is_RT5350 = 1
Linux version 2.6.33.2 (kwest@enzo) (gcc version 4.3.3 (GCC) ) #1 Wed Jan 26 19:29:59 CST 2011

 The CPU feqenuce set to 360 MHz
bootconsole [early0] enabled
CPU revision is: 0001964c (MIPS 24Kc)
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock1 noinitrd
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=000602a0
Readback ErrCtl register=000602a0
Memory: 28976k/32768k available (2623k kernel code, 3792k reserved, 613k data, 152k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:128
setup_irq 6
CPU frequency 360.00 MHz
[debug] (r4k_clockevent_init line: 172)
[debug] 128 aba9500 (r4k_clockevent_init line: 176)
[debug] (r4k_clockevent_init line: 185)
[debug] irq: 5 , 800086d4 , (r4k_clockevent_init line: 195)
4,[debug] (r4k_clockevent_init line: 217)
5,[debug] (r4k_clockevent_init line: 222)
setup_irq 5
[debug] (r4k_clockevent_init line: 228)
If the above line no "setup_irq 5", mean irq for timer is not installed
Calibrating delay loop... 239.61 BogoMIPS (lpj=479232)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Load RT2880 Timer Module(Wdg/Soft)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
Ralink gpio driver initialized
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
console [ttyS1] enabled, bootconsole disabled12) is a 16550A
console [ttyS1] enabled, bootconsole disabled
deice id : ef 40 16 0 0 (40160000)
Warning: un-recognized chip ID, please update SPI driver!
25064BVSIG(ef 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
seama skip the header
xxxxxxxx: squashfs filesystem found at offset 1507392, magic 73717368
Creating 8 MTD partitions on "raspi":
0x000000170060-0x0000003b5060 : "rootfs"
0x000000050000-0x0000003e0000 : "upgrade"
0x000000040000-0x000000050000 : "devconf"
0x000000030000-0x000000040000 : "devdata"
0x0000003e0000-0x000000400000 : "langpack"
0x000000000000-0x000000400000 : "flash"
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000038000 : "boot env"
MAC_ADRH -- : 0x00000000
MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.0  256 rx/tx descriptors allocated, mtu = 1500!
eth2: set mac address
MAC_ADRH -- : 0x0000000c
MAC_ADRL -- : 0x43288081
PROC INIT OK!
rt3052 access driver initialization.
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
skb rate limit initialization.
GACT probability NOT on
u32 classifier
    Actions configured
nf_conntrack version 0.5.0 (452 buckets, 1808 max)
nf_conntrack_rtsp v0.6.21 loading
nf_conntrack_rtsp  port #0: 554
nf_conntrack_rtsp  port #1: 557
xt_time: kernel timezone is -0000
nf_nat_rtsp v0.6.21 loading
BCM fast NAT: INIT
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:1.
Freeing unused kernel memory: 152k freed
init started: BusyBox v1.14.1 (2011-01-26 19:30:07 CST)
starting pid 28, tty '': '/etc/init.d/rcS'
Algorithmics/MIPS FPU Emulator v1.5
[/etc/init.d/S10init.sh]
[/etc/init.d/S16ipv6.sh]
[/etc/init.d/S19init.sh]
[/etc/init.d/S20init.sh]
DEVCONF: no config data available (ret=-1) !
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!     Uable to read device config.     !!
!! Setting is reset to factory default. !!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
  DEFNODE[/etc/defnodes/S10phyinf.php]
  DEFNODE[/etc/defnodes/S11devdata.xml]
  DEFNODE[/etc/defnodes/S12flashspeed.php]
  DEFNODE[/etc/defnodes/S20device.xml]
  DEFNODE[/etc/defnodes/S22timezone.php]
[/etc/scripts/setdate.sh] 01/01/2000 ...
Sat Jan  1 08:00:03 GMT 2000
  DEFNODE[/etc/defnodes/S30device.php]
  DEFNODE[/etc/defnodes/S30device.xml]
  DEFNODE[/etc/defnodes/S31diagnostic.xml]
  DEFNODE[/etc/defnodes/S31locale.php]
  DEFNODE[/etc/defnodes/S32layout.php]
  DEFNODE[/etc/defnodes/S33wifi.php]
  DEFNODE[/etc/defnodes/S40device.xml]
  DEFNODE[/etc/defnodes/S90sessions.php]
  DEFNODE[/etc/defnodes/S90upnpigd.php]
  DEFNODE[/etc/defnodes/S90upnpwfa.php]
SERVD: start service [LOGD]
[/etc/init.d/S20interfaces.sh]
eth2: set mac address
MAC_ADRH -- : 0x00002810
MAC_ADRL -- : 0x7b623a97

phy_tx_ring = 0x00c00000, tx_ring = 0xa0c00000

phy_rx_ring0 = 0x00c01000, rx_ring0 = 0xa0c01000
RT305x_ESW: Link Status Changed
[/etc/init.d/S45gpiod.sh]
[/etc/init.d/S50config.sh]
[/etc/init.d/rcS] done!
Factory reset time : 5 secs
[/etc/init0.d/S21layout.sh]: start ...
SERVD: event [WANPORT.LINKDOWN] not found!
SERVD: start service [LAYOUT]
[/etc/init0.d/S21wlan.sh]: start ...
device eth2 entered promiscuous mode
device eth2.0 entered promiscuous mode
interface ra0 does not exist!
br0: port 1(eth2.0) entering forwarding state
SERVD: start service [PHYINF.ETH-1]
rt2860v2_ap: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint


=== pAd = c055c000, size = 481192 ===

<-- RTMPAllocAdapterBlock, Status=0
RT305x_ESW: Link Status Changed
[/etc/init0.d/S40event.sh]: start ...
SERVD: event [SEALPAC.LOAD/default]
[/etc/init0.d/S40gpioevent.sh]: start ...
SEAMA: '/dev/mtdblock/5' is not a seama file !
[/etc/init0.d/S41autowan.sh]: start ...
[/etc/init0.d/S41inf.sh]: start ...
[/etc/init0.d/S41smart404.sh]: start ...
[/etc/init0.d/S42pthrough.sh]: start ...
[/etc/init0.d/S65ddnsd.sh]: start ...
[/etc/init0.d/S80telnetd.sh]: start ...
RT305x_ESW: Link Status Changed
[/etc/init0.d/rcS] done!

Please press Enter to activate this console. SERVD: start service [PHYINF.ETH-2]
SERVD: start service [WIFI.WLAN-1]
SERVD: start service [LOGD]
SERVD: service [LOGD] is already started.
SERVD: start service [BRIDGE]
BRIDGE: The device is not in the bridge mode.
SERVD: start service [LAN]
SERVD: start service [WAN]
SERVD: start service [DEVICE.PASSTHROUGH]
SERVD: start service [WIFI]
RX DESC a18f8000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
RTMP_TimerListAdd: add timer obj c05a2f88!
RTMP_TimerListAdd: add timer obj c0579f44!
RTMP_TimerListAdd: add timer obj c057a048!
RTMP_TimerListAdd: add timer obj c0579f6c!
RTMP_TimerListAdd: add timer obj c057182c!
RTMP_TimerListAdd: add timer obj c0571548!
1. Phy Mode = 9
2. Phy Mode = 9
TXALC> bInternalTxALC = 1
3. Phy Mode = 9
RTMP_TimerListAdd: add timer obj c05610cc!
NICInitAsicFromEEPROM: pAd->TxPowerCtrl.bInternalTxALC = 1
RT305x_ESW: Link Status Changed
Channel 1 TSSI delta=0
Channel 2 TSSI delta=0
Channel 3 TSSI delta=0
Channel 4 TSSI delta=0
Channel 5 TSSI delta=0
Channel 6 TSSI delta=0
Channel 7 TSSI delta=0
Channel 8 TSSI delta=0
Channel 9 TSSI delta=0
Channel 10 TSSI delta=0
Channel 11 TSSI delta=0
Channel 12 TSSI delta=0
Channel 13 TSSI delta=0
Channel 14 TSSI delta=0
TSSIBase(0x6E) = 18, TxPowerOFDM54 = 8
EEPROM_CCK_MCS0_MCS1(0xDE) = 0x8
---> TSSIRatioDot7
EEPROM_CCK_MCS2_MCS3(0xDF) = 0x8
---> TSSIRatioDot7
RT5350_desiredTSSIOverCCK[0] = 389232
RT5350_desiredTSSIOverCCK[1] = 389232
RT5350_desiredTSSIOverCCK[2] = 389232
RT5350_desiredTSSIOverCCK[3] = 389232
EEPROM_OFDM_MCS0_MCS1(0xE0) = 0xA
---> TSSIRatioDot7
EEPROM_OFDM_MCS2_MCS3(0xE1) = 0x9
---> TSSIRatioDot7
EEPROM_OFDM_MCS4_MCS5(0xE2) = 0x9
---> TSSIRatioDot7
EEPROM_OFDM_MCS6_MCS7(0xE3) = 0x8
RT5350_desiredTSSIOverOFDM[0] = 331296
RT5350_desiredTSSIOverOFDM[1] = 331296
RT5350_desiredTSSIOverOFDM[2] = 281976
RT5350_desiredTSSIOverOFDM[3] = 281976
RT5350_desiredTSSIOverOFDM[4] = 281976
RT5350_desiredTSSIOverOFDM[5] = 281976
RT5350_desiredTSSIOverOFDM[6] = 240000
RT5350_desiredTSSIOverOFDM[7] = 240000
EEPROM_HT_MCS0_MCS1(0xE4) = 0x8
---> TSSIRatioDot7
EEPROM_HT_MCS2_MCS3(0xE5) = 0x8
---> TSSIRatioDot7
EEPROM_HT_MCS4_MCS5(0xE6) = 0x8
---> TSSIRatioDot7
---> TSSIRatioDot7
EEPROM_HT_MCS6_MCS7(0xE7) = 0x8
---> TSSIRatioDot7
---> TSSIRatioDot7
---> TSSIRatioDot7
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff 00 00 00 00
SYNC - BBP R4 to 20MHz.l
RT305x_ESW: Link Status Changed
RTMP_TimerListAdd: add timer obj c0571acc!
Main bssid = 28:10:7b:62:3a:96
<==== rt28xx_init, Status=0
0x1300 = 00064380
SERVD: event [WLAN-1.UP/default]
can't find port ra0 in bridge br0
/proc/net/br_forward_br0: can't create
device ra0 entered promiscuous mode
br0: port 2(ra0) entering forwarding state
[/etc/scripts/wps.sh] setie ...
Configuration file: /var/servd/hostapd-ra0.conf
Cannot read /proc/net/wireless
Using interface ra0 with hwaddr 28:10:7b:62:3a:96 and ssid 'dlink'
hostapd_setup_interface: return 0
SERVD: stop service [MULTICAST]
SERVD: service [MULTICAST] is already stopped.
SERVD: start service [MULTICAST]
SERVD: start service [IPTABLES]
Network interface reset count v1.0
SERVD: start service [IP6TABLES]
SERVD: start service [IPTABLES]
SERVD: service [IPTABLES] is already started.
SERVD: start service [IP6TABLES]
SERVD: service [IP6TABLES] is already started.
SERVD: start service [INET.LAN-1]
[/var/servd/INET.LAN-1_start.sh]: starting LAN-1...
SERVD: event [LAN-1.UP/default]
[/var/servd/INET.LAN-1_start.sh]: starting LAN-1 done !!!
SERVD: start service [INET.LAN-2]
ifsetup: (LAN-2) not active.
SERVD: service [INET.LAN-2] return error 8.
SERVD: start service [INET.LAN-3]
[/var/servd/INET.LAN-3_start.sh]: starting LAN-3...
LAN-3 a is link local interface.
SERVD: event [LAN-3.UP/default]
[/var/servd/INET.LAN-3_start.sh]: starting LAN-3 done !!!
SERVD: start service [INET.LAN-4]
#!/bin/sh
# No inet profile!!
exit 9

SERVD: start service [IPTMACCTRL]
SERVD: start service [IPTURLCTRL]
SERVD: start service [IPTPORTT]
SERVD: start service [IP6T.LAN-1]
SERVD: start service [IP6T.LAN-2]
SERVD: start service [IP6T.LAN-3]
SERVD: start service [IP6T.LAN-4]
SERVD: start service [IPTABLES]
SERVD: service [IPTABLES] is already started.
SERVD: start service [IP6TABLES]
SERVD: service [IP6TABLES] is already started.
SERVD: start service [INET.WAN-1]
[/var/servd/INET.WAN-1_start.sh]: starting WAN-1...
[/var/servd/INET.WAN-1_start.sh]: starting WAN-1 done !!!
SERVD: start service [INET.WAN-2]
ifsetup: (WAN-2) not active.
SERVD: service [INET.WAN-2] return error 8.
SERVD: start service [INET.WAN-3]
[/var/servd/INET.WAN-3_start.sh]: starting WAN-3...
WAN-3 a is link local interface.
SERVD: event [WAN-3.UP/default]
[/var/servd/INET.WAN-3_start.sh]: starting WAN-3 done !!!
SERVD: start service [INET.WAN-4]
ifsetup: (WAN-4) not active.
SERVD: service [INET.WAN-4] return error 8.
SERVD: start service [IPTMASQ]
/proc/sys/net/ipv4/ip_personality_sport: can't create
/proc/sys/net/ipv4/ip_personality_enable: can't create
SERVD: start service [IPTVSVR]
SERVD: start service [IPTPFWD]
SERVD: start service [IPTPORTT]
SERVD: service [IPTPORTT] is already started.
SERVD: start service [IPTDMZ]
IPTDMZ: cnt= 1
SERVD: start service [IPT.WAN-1]
SERVD: start service [IP6T.WAN-1]
SERVD: start service [IPT.WAN-2]
SERVD: start service [IP6T.WAN-2]
SERVD: start service [IPT.WAN-3]
SERVD: start service [IP6T.WAN-3]
SERVD: start service [IPT.WAN-4]
SERVD: start service [IP6T.WAN-4]
SERVD: stop service [IPT.LAN-1]
SERVD: service [IPT.LAN-1] is already stopped.
SERVD: start service [IPT.LAN-1]
/proc/fastnat/forskipsupport: can't create
SERVD: stop service [IPT.LAN-2]
SERVD: service [IPT.LAN-2] is already stopped.
SERVD: start service [IPT.LAN-2]
/proc/fastnat/forskipsupport: can't create
SERVD: stop service [IPT.LAN-3]
SERVD: service [IPT.LAN-3] is already stopped.
SERVD: start service [IPT.LAN-3]
SERVD: service [IPT.LAN-3] return error 108.
SERVD: stop service [IPT.LAN-4]
SERVD: service [IPT.LAN-4] is already stopped.
SERVD: start service [IPT.LAN-4]
SERVD: service [IPT.LAN-4] return error 108.
SERVD: stop service [INFSVCS.LAN-1]
SERVD: service [INFSVCS.LAN-1] is already stopped.
SERVD: start service [INFSVCS.LAN-1]
SERVD: event [LAN-1.CONNECTED] not found!
SERVD: event [INFSVCS.LAN-1.UP/default]
SERVD: stop service [INFSVCS.LAN-3]
SERVD: service [INFSVCS.LAN-3] is already stopped.
SERVD: start service [INFSVCS.LAN-3]
SERVD: event [STATUS.READY/default]
SERVD: event [LAN-3.CONNECTED] not found!
SERVD: event [INFSVCS.LAN-3.UP] not found!
SERVD: stop service [INFSVCS.WAN-3]
SERVD: service [INFSVCS.WAN-3] is already stopped.
SERVD: start service [INFSVCS.WAN-3]
SERVD: event [WAN-3.CONNECTED] not found!
SERVD: event [UPDATERESOLV/default]
SERVD: event [INFSVCS.WAN-3.UP] not found!
SERVD: event [UPNP.IGD.NOTIFY.WANIPCONN1] not found!
SERVD: start service [ENLAN]
RT305x_ESW: Link Status Changed
SERVD: start service [HTTP.LAN-1]
SERVD: start service [UPNP.LAN-1]
SERVD: event [UPNP.ALIVE.LAN-1/default]
SERVD: start service [NEAP.LAN-1]
SERVD: start service [NAMERESOLV.LAN-1]
SERVD: start service [DHCPS4.LAN-1]
SERVD: start service [DNS4.LAN-1]
RT305x_ESW: Link Status Changed
SERVD: stop service [ROUTE.STATIC]
SERVD: service [ROUTE.STATIC] is already stopped.
SERVD: start service [ROUTE.STATIC]
SERVD: stop service [ROUTE.IPUNNUMBERED]
SERVD: service [ROUTE.IPUNNUMBERED] is already stopped.
SERVD: start service [ROUTE.IPUNNUMBERED]
SERVD: stop service [MULTICAST]
SERVD: start service [MULTICAST]
SERVD: stop service [IPTDEFCHAIN]
SERVD: service [IPTDEFCHAIN] is already stopped.
SERVD: start service [IPTDEFCHAIN]
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
SERVD: stop service [ROUTE.DYNAMIC]
SERVD: service [ROUTE.DYNAMIC] is already stopped.
SERVD: start service [ROUTE.DYNAMIC]
SERVD: service [ROUTE.DYNAMIC] return error 108.
SERVD: start service [ENLAN]
SERVD: service [ENLAN] is already started.
SERVD: start service [HTTP.LAN-3]
SERVD: start service [NAMERESOLV.LAN-3]
SERVD: start service [HTTP.WAN-3]
httpsetup: (WAN-3) not active.
SERVD: service [HTTP.WAN-3] return error 8.
SERVD: stop service [IP6TDEFCHAIN]
SERVD: service [IP6TDEFCHAIN] is already stopped.
SERVD: start service [IP6TDEFCHAIN]
SERVD: stop service [ROUTE6.DYNAMIC]
SERVD: service [ROUTE6.DYNAMIC] is already stopped.
SERVD: start service [ROUTE6.DYNAMIC]
SERVD: stop service [ROUTE6.STATIC]
SERVD: service [ROUTE6.STATIC] is already stopped.
SERVD: start service [ROUTE6.STATIC]
SERVD: stop service [DNS]
SERVD: service [DNS] is already stopped.
SERVD: start service [DNS]
killall: dnsmasq: no process killed
SERVD: stop service [HTTP]
SERVD: service [HTTP] is already stopped.
SERVD: start service [HTTP]
SERVD: event [HTTP.UP] not found!
SERVD: stop service [IPT.WAN-3]
SERVD: start service [IPT.WAN-3]



Here is DD-WRT not booting

Code:
U-Boot 1.1.3 (Feb 25 2011 - 14:31:26) (ALPHA)

SVN revision: 499
Target board: WRG-N49

Board: Ralink APSoC DRAM:  32 MB                           
spi_wait_nsec: 42                                           
spi device id: ef 40 16 0 0 (40160000)                     
find flash: W25Q32BV
..============================================
Ralink UBoot Version: 3.5.1.0
--------------------------------------------
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:Feb 25 2011  Time:14:31:26
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
## Powering down port 0 ~ 3.

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
   A: Load  Runtime code then write to Flash via Serial.

You choosed 3

 0
   
3: System Boot system code via Flash.
## Booting image at bc050000 ...
.   Image Name:   DD-WRT v24 Linux Kernel Image
   Created:      2012-06-08   8:29:25 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    913640 Bytes = 892.2 kB
   Load Address: 80000000
   Entry Point:  8020ed80
.............   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

hessie2k
DD-WRT Novice


Joined: 10 Apr 2011
Posts: 10

PostPosted: Tue Jul 03, 2012 12:56    Post subject: Reply with quote
Any news ?
riahc3
DD-WRT User


Joined: 04 May 2007
Posts: 244

PostPosted: Thu Jul 26, 2012 10:35    Post subject: Reply with quote
hessie2k wrote:
Any news ?

The news does not exist. This router will not get DD-WRT.

[/endthread]
Mikesz
DD-WRT Novice


Joined: 18 Oct 2012
Posts: 1

PostPosted: Thu Oct 18, 2012 15:43    Post subject: Reply with quote
Hi.

Is there hope that the version B5 will be supported by the DD-WRT?
The DIR-600 at present sold, is usually available in the hardware version B5.
Therefore there is a considerable interest
ccmuhah
DD-WRT Novice


Joined: 26 Mar 2012
Posts: 3

PostPosted: Sun Nov 18, 2012 19:50    Post subject: Reply with quote
Mikesz wrote:
Hi.

Is there hope that the version B5 will be supported by the DD-WRT?
The DIR-600 at present sold, is usually available in the hardware version B5.
Therefore there is a considerable interest


I totally agree with you. I hope we get DD-WRT on our routers soon...
vavy
DD-WRT Novice


Joined: 21 Jan 2009
Posts: 8

PostPosted: Thu Dec 06, 2012 11:11    Post subject: Reply with quote
ccmuhah wrote:
Mikesz wrote:
Hi.

Is there hope that the version B5 will be supported by the DD-WRT?
The DIR-600 at present sold, is usually available in the hardware version B5.
Therefore there is a considerable interest


I totally agree with you. I hope we get DD-WRT on our routers soon...


Am i right -
the problem with ddwrt' supportiong of DIR300NRUB5 is the same as with DIR600B5 ?

It is the chip ralink 5350 ?
gmajnkek
DD-WRT Novice


Joined: 23 Dec 2012
Posts: 1

PostPosted: Sun Dec 23, 2012 19:03    Post subject: Reply with quote
Anyone tryed this one:
ftp://ftp.dlink.cz/dir/dir-600/driver_software/

Seems to be new...date 6.12.2012
lelekx
DD-WRT Novice


Joined: 30 Jun 2010
Posts: 6

PostPosted: Tue Mar 19, 2013 20:09    Post subject: Reply with quote
OpenWRT has some work in progress. Test builds are avalilable to download:
http://wiki.umeahackerspace.se/w/index.php?title=Dir-300b5
Patches to openwrt's code can be downloaded from GitHub: https://github.com/Squonk42/OpenWrt-RT5350
Chagnes can't be too hard to port to DD-WRT (I guess).
mwchang
DD-WRT Novice


Joined: 26 Mar 2013
Posts: 3

PostPosted: Tue Mar 26, 2013 14:41    Post subject: Reply with quote
gmajnkek wrote:
Anyone tryed this one:
ftp://ftp.dlink.cz/dir/dir-600/driver_software/
Seems to be new...date 6.12.2012


It's now version 2.15! Installed it and hasn't had any problem so far....
mwchang
DD-WRT Novice


Joined: 26 Mar 2013
Posts: 3

PostPosted: Tue Mar 26, 2013 14:43    Post subject: Reply with quote
lelekx wrote:
OpenWRT has some work in progress. Test builds are avalilable to download:
Chagnes can't be too hard to port to DD-WRT (I guess).

Glad to hear this.... but it's OpenWRT not DD-WRT... Smile
mitza97
DD-WRT User


Joined: 29 Dec 2011
Posts: 100

PostPosted: Sat Mar 30, 2013 19:42    Post subject: Reply with quote
Hello.
I subscribe to this topic as owner of this equipment.
I had a TL-WR740N v4 which I trashed because I'm tired of his problems...Mad This unit working very fine, but i wish to try DD-WRT on it. Will be possible soon ? Or not ?
mwchang
DD-WRT Novice


Joined: 26 Mar 2013
Posts: 3

PostPosted: Tue May 14, 2013 15:37    Post subject: Reply with quote
Official firmware 2.16B has been release!!!

ftp://ftp.dlink.cz/dir/dir-600/driver_software/DIR-600_fw_revB5_2-16B02_all_en_20130422.zip
Isnogud93
DD-WRT Novice


Joined: 15 Jan 2014
Posts: 1

PostPosted: Wed Jan 15, 2014 16:00    Post subject: Reply with quote
Is there any develpement in dd wrt for rev B5? I am really interesten in it couse its the free router that comes with the internet contract
Goto page Previous  1, 2, 3, 4, 5  Next Display posts from previous:    Page 4 of 5
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum