belkin f5d7230-4 v2000 - can only ping during reset?

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Author Message
by1990
DD-WRT Novice


Joined: 09 Aug 2009
Posts: 8

PostPosted: Thu Aug 16, 2012 0:07    Post subject: belkin f5d7230-4 v2000 - can only ping during reset? Reply with quote
After flashing dd-wrt firmware, i try to connect to the webgui but couldn't get to it. So i tried to ping the router 192.168.1.1 with my system ip 192.168.1.3 and i got destination unreachable. So then i tried to ping to the belkin router default gateway 192.168.2.1 with my system ip 192.168.2.3 and got no luck either. But then i did a ping -t on the router default gateway and reset it, it returned a reply with ttl=100 for a few seconds and after a while it became destination unreachable again. I tried hard reset a couple of times but that didn't solve the issue.

So is my router bricked or not? Is there any way to save it?

Thanks in advance!
Sponsor
feliciano
DD-WRT Guru


Joined: 24 Oct 2008
Posts: 654
Location: Venezuela

PostPosted: Fri Aug 17, 2012 15:47    Post subject: Reply with quote
Something went wrong with your procedure.
So, since you can ping it at boot time, tftp the firmware again.
But first, double check you are using the correct file.

_________________
Worked with: WR850Gv2, WHR-HP-G54, WRT54GL, WRT150N, WL-520gU, DIR-600 B1, WLI-TX4-G54HP, WHR-HP-GN...
Working with: F7D7301, F7D3302, among others.


Last edited by feliciano on Fri Aug 17, 2012 23:10; edited 1 time in total
James2k
DD-WRT User


Joined: 23 Oct 2011
Posts: 392

PostPosted: Fri Aug 17, 2012 19:57    Post subject: Reply with quote
TTL 100 is your bootloader, so you might be in luck. Try and initiate a tftp transfer during the ping responses. Timing is critical.
_________________
James



Routers:
Asus RT-N66U - K3.x v24-sp2 (12/17/13) big 23194 (BrainSlayer) - Main Router
WNR3500L - K26 v24-sp2 (08/19/13) kongmod 22200M (Kong) - OTRW2 Test Unit
Belkin F5D7230-4 - K24 v24-sp2 (12/24/09) micro-plus-ssh 13491M (Eko) - Access Point
2x WNR2000v3 DD-WRT v24-sp2 (03/08/12) std 18777 (BrainSlayer) - Repeater Bridge
by1990
DD-WRT Novice


Joined: 09 Aug 2009
Posts: 8

PostPosted: Wed Aug 22, 2012 20:42    Post subject: Reply with quote
I tried tftp a few times, still having the same issue.
I am using Bv2000 Micro SF, which i got directly from the database.
Is there anything else i could try?
Thanks again!
feliciano
DD-WRT Guru


Joined: 24 Oct 2008
Posts: 654
Location: Venezuela

PostPosted: Wed Aug 22, 2012 23:12    Post subject: Reply with quote
As James2K said: timing is critical.
So;
Connect directly to a LAN port of the router
Set your PC to an static IP address, say 192.168.1.11, and force it to 10Mbps half duplex
Open two command prompt windows, in one do a ping 192.168.1.1 -t, and in the other write tftp -i 192.168.1.1 PUT firmware.bin but don´t hit enter yet
As soon as you see ping responses, hit enter in the other window
Wait until finish upload
If it doesn´t work, try a different build.

If it doesn´t solve your problem, you´ll have to research about JTAG and/or serial recovery.

_________________
Worked with: WR850Gv2, WHR-HP-G54, WRT54GL, WRT150N, WL-520gU, DIR-600 B1, WLI-TX4-G54HP, WHR-HP-GN...
Working with: F7D7301, F7D3302, among others.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum