New Linksys/Cisco E800 N150 Router 5/5/13 TEST BIN PAGE 1

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2  Next
Author Message
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1187

PostPosted: Sat May 04, 2013 7:33    Post subject: New Linksys/Cisco E800 N150 Router 5/5/13 TEST BIN PAGE 1 Reply with quote
Here she is the new linksys E800 N150 router with pictures and serial dump.. I wonder if this is the new router series we are going to see now that belkin owns linksys, comments????

picked this up for $34.95 USD at walmart.

-Fractal


Uploaded at Picoodle.com

Uploaded at Picoodle.com

Begin Serial Dump:

Code:
# Decompressing...done
Start to blink diag led ...


CFE version 5.100.138.11 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 01/16/13 16:31:29 HKT (root@t.sw3)
Copyright (C) 2000-2008 Broadcom Corporation.

Initializing Arena
Initializing Devices.

No DPN
This is a Serial Flash
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 0004001B  (28)
os      #02   0004001C -> 007EFFFF  (8060900)
nvram   #03   007F0000 -> 007FFFFF  (65536)
Partition information:
boot    #00   00000000 -> 0003FFFF  (262144)
trx     #01   00040000 -> 007EFFFF  (8060928)
nvram   #02   007F0000 -> 007FFFFF  (65536)
BCM47XX_GMAC_ID
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.11
CPU type 0x19749: 300MHz
Total memory: 32768 KBytes

CFE mem:    0x80700000 - 0x807AE1F0 (713200)
Data:       0x80743460 - 0x80747540 (16608)
BSS:        0x80747540 - 0x807481F0 (3248)
Heap:       0x807481F0 - 0x807AC1F0 (409600)
Stack:      0x807AC1F0 - 0x807AE1F0 (8192)
Text:       0x80700000 - 0x80743460 (275552)

Boot version: v5.3.7
The boot is CFE
mac_init(): Find mac [48:f8:b3:XX:XX:XX] in location 0
Nothing...

### CLKDIV= 0x8080842, SFlashClkDiv=8 clkdivsf=2 ###

### Change it to 0x2080842 (2) ###
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Device eth0:  hwaddr 48-F8-B3-XX-XX-XX, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
  Len:     0x6AF000   (7008256)   (0xBC040000)
  Offset0: 0x1C      (28)      (0xBC04001C)
  Offset1: 0x14FA00   (1374720)   (0xBC18FA00)
  Offset2: 0x0   (0)   (0xBC040000)
  Header CRC:    0x7C27E183
  Calculate CRC: 0x7C27E183
Image 1 is OK
Try to load image 1.
Waiting for 3 seconds to upgrade ...
CMD: [load -raw -addr=0x807ae1f0 -max=0x1851e10 :]
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: _tftpd_open(): retries=0/3
_tftpd_open(): retries=1/3
_tftpd_open(): retries=2/3

### Start=377432862 E=705658085 Delta=328225223 ###
Failed.
Could not load :: Timeout occured
CMD: [boot -raw -z -addr=0x80001000 -max=0x6ff000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ...... 3334520 bytes read

### Start=710479370 E=885586935 Delta=175107565 ###
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22 (root@t.sw3) (gcc version 4.2.3) #16 Wed Jan 16 15:59:29 HKT 2013
prom_init:123: memory size is (2000000) by automatily calculating!
prom_init:190: mem:2000000, actually, test by seal!
CPU revision is: 00019749
Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal          0 ->     8192
  HighMem      8192 ->     8192
early_node_map[1] active PFN ranges
    0:        0 ->     8192
Built 1 zonelists.  Total pages: 8192
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM53572 rev 1 at 300 MHz
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 27916k/32768k available (2543k kernel code, 4836k reserved, 508k data, 204k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: no core
PCI: no core
PCI: Fixing up bus 0
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
fuse init (API version 7.8)
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Register DIAG LED in /proc/sys/diag_blink.
The DIAG LED GPIO is 6.
Register DIAG LED success in /proc/sys/diag_blink.
pflash: found no supported devices
sflash: squash filesystem with lzma found at block 1598
Creating 4 MTD partitions on "sflash":
0x00000000-0x00040000 : "boot"
0x00040000-0x007f0000 : "linux"
0x0018fa00-0x007f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x007f0000-0x00800000 : "nvram"
u32 classifier
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
edward ====to register conntrack protocol helper for esp:
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
edward =======nf_nat_proto_esp_init
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
Warning: unable to open an initial console.
Failed to execute /init
ctmisc: module license 'unspecified' taints kernel.
Register /dev/ctmisc device, major:10 minor:255
cmd=[/sbin/hotplug2 --coldplug & ]
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
/dev/nvram: No such file or directory
[sighandler]: No more events to be processed, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
hahaha enter wl_nvram_convert!
The boot is CFE
Algorithmics/MIPS FPU Emulator v1.5
/dev/: cannot create
cmd=[misc -t get_mac -w 3 ]
type = [get_mac]ctmisc_ioctl: cmd=0x11, buffer size=404

get_data(): cmdata_init(): base = 0xbc03ee00
d=0x11 count=8 ldata_init(): location = [1], mydatas index = 1
en=18
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get MAC count is [1]
get_data(): MAC 0: [48:f8:b3:16:f5:f1ÿ]
get_data name get_mac write_to_nv 3
get_data(): done
cmd=[misc -t get_wsc_pin -w 3 ]
type = [get_wsc_ctmisc_ioctl: cmd=0x26, buffer size=404
pin]
get_data()data_init(): base = 0xbc03f400
: cmd=0x26 countdata_init(): location = [1], mydatas index = 1
=8 len=8
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get WSC count is [1]
get_data(): WSC 0: [31911269]
get_data name get_wsc_pin write_to_nv 3
get_data(): done
cmd=[misc -t get_sn -w 3 ]
type = [get_sn]ctmisc_ioctl: cmd=0x15, buffer size=404

get_data(): cmdata_init(): base = 0xbc03fe32
d=0x15 count=8 ldata_init(): location = [1], mydatas index = 1
en=20
ctmisc_ioctl: index=1
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get SN count is [1]
get_data(): SN 0: [13910C62338237ÿÿÿÿÿÿ]
get_data name get_sn write_to_nv 3
get_data(): done
cmd=[misc -t get_flash_type -w 1 ]
type = [get_flasctmisc_ioctl: cmd=0x17, buffer size=404
h_type]
get_flasflash_init: sflash type 0x100
sh_type(): cmd=0sflash_init: sflash type 0x16
x17 count=0 len=Flash Type: SFLASH 8192 kB
0
tallest:=====(ctmisc ioctl done...)=====
Get FLASH TYPE is [SFLASH 8192 kB]
cmd=[misc -t get_pa0idxval -w 3 ]
type = [get_pa0ictmisc_ioctl: cmd=0x28, buffer size=404
dxval]
get_datadata_init(): base = 0xbc03efe0
(): cmd=0x28 coudata_init(): location = [0], mydatas index = 0
nt=8 len=24
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get PA0IDXVAL count is [0]
get_data name get_pa0idxval write_to_nv 3
get_data(): done
Using default PA0 value
cmd=[misc -t get_pa1idxval -w 3 ]
type = [get_pa1ictmisc_ioctl: cmd=0x2a, buffer size=404
dxval]
get_datadata_init(): base = 0xbc03ef20
(): cmd=0x2a coudata_init(): location = [0], mydatas index = 0
nt=8 len=24
ctmisc_ioctl: index=0
tallest:=====(ctmisc ioctl done...)=====
get_data(): Get PA1IDXVAL count is [0]
get_data name get_pa1idxval write_to_nv 3
get_data(): done
Using default PA1 value
Cannot find lang from /proc/mtd
ret = -1
www -> /www
mount: No such file or directory
cmd=[insmod emf ]
cmd=[insmod igs ]
cmd=[insmod ctf ]
Needed modules: et wl ip6table_mangle ip6table_filter ip6t_rt ip6t_frag ip6t_ipv6header ip6t_REJECT ip6t_LOG ip6t_ipv6range tunnel4 sit tunnel6 ip6_tunnel nf_conntrack_h323.ko nf_nat_h323.ko xt_TCPMSS.ko
cmd=[insmod et ]
cmd=[insmod wl ]
cmd=[insmod ip6table_mangle ]
cmd=[insmod ip6table_filter ]
cmd=[insmod ip6t_rt ]
cmd=[insmod ip6t_frag ]
cmd=[insmod ip6t_ipv6header ]
cmd=[insmod ip6t_REJECT ]
cmd=[insmod ip6t_LOG ]
cmd=[insmod ip6t_ipv6range ]
cmd=[insmod tunnel4 ]
cmd=[insmod sit ]
cmd=[insmod tunnel6 ]
cmd=[insmod ip6_tunnel ]
cmd=[insmod nf_conntrack_h323.ko ]
cmd=[insmod nf_nat_h323.ko ]
cmd=[insmod xt_TCPMSS.ko ]
cmd=[insmod dnshook ]
Hit enter to continue...cmd=[misc -t get_country -w 3 ]
type = [get_country]
get_data(): cmd=0x2c count=30 len=2
get_data(): Get COUNTRY count is [1]
get_data(): COUNTRY 0: [US]
get_data name get_country write_to_nv 3
get_data(): done
waitpid: No child processes
The chipset is BCM5357 for E800
cmd=[killall httpd ]
killall: httpd: no process killed
killall: check_http.sh: no process killed
cmd=[killall wm-httpd ]
killall: wm-httpd: no process killed
waitpid: No child processes
cmd=[et robowr 0x02 0x06 0x001000a0 ]
cmd=[resetbutton ]
cmd=[vconfig set_name_type VLAN_PLUS_VID_NO_PAD ]
cmd=[vconfig add eth0 1 ]
cmd=[vconfig set_ingress_map vlan1 0 0 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 1 1 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 2 2 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 3 3 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 4 4 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 5 5 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 6 6 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan1 7 7 ]
waitpid: No child processes
cmd=[vconfig add eth0 2 ]
cmd=[vconfig set_ingress_map vlan2 0 0 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 1 1 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 2 2 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 3 3 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 4 4 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 5 5 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 6 6 ]
waitpid: No child processes
cmd=[vconfig set_ingress_map vlan2 7 7 ]
waitpid: No child processes
cmd=[brctl addbr br0 ]
cmd=[brctl setfd br0 0 ]
waitpid: No child processes
cmd=[brctl stp br0 dis ]
waitpid: No child processes
cmd=[brctl addif br0 vlan1 ]
waitpid: No child processes
br0: No child processes
cmd=[wlconf vlan1 up ]
vlan1: Operation not supported
Write wireless mac successfully
cmd=[brctl addif br0 eth1 ]
waitpid: No child processes
br0: No child processes
cmd=[wlconf eth1 up ]
eth1: Operation not supported
eth1: Operation not permitted
wlconf: PHYTYPE: 4
eth1: Invalid argument
eth1: Invalid argument
eth1: Operation not supported
eth1: Operation not supported
cmd=[brctl addif br0 eth1 ]
device eth1 is already a member of a bridge; can't enslave it to bridge br0.
waitpid: No child processes
Write wireless mac fail : : No such device
cmd=[brctl addif br0 eth2 ]
interface eth2 does not exist!
eth2: No such device
cmd=[brctl addif br0 eth3 ]
interface eth3 does not exist!
eth3: No such device
Set 1 to /proc/sys/net/ipv6/conf/br0/forwarding ...
lo: File exists
Set 66560 to /proc/sys/net/core/rmem_max ...
set 2048 to /proc/sys/vm/min_free_kbytes
cmd=[tftpd -s /tmp -c -l -P E800 ]
cmd=[cron ]
The boot is CFE
tftp server started
tftpd: standalone socket
cmd=[httpd ]
cmd=[/tmp/wm-httpd -p 52000 -w ]
cmd=[touch /tmp/hosts ]
waitpid: No child processes
cmd=[dnsmasq -R -h -i br0 -c 0 -r /tmp/resolv.conf ]
cmd=[route del -net 224.0.0.0 netmask 240.0.0.0 dev br0 ]
route: ioctl 0x890c failed: No such process
[Dnsmasq], fec00000000000004af8b3fffe16f5f1 is IFA_F_TENTATIVE, wait for 1 sec.
waitpid: No child processes
cmd=[route add -net 224.0.0.0 netmask 240.0.0.0 dev br0 ]
waitpid: No child processes
cmd=[cesmDNS -o /tmp/.mdns_host_info -d -h Cisco38237 -l 192.168.1.1 ]
Starting in daemon mode
br0 192.168.1.100  86400
write_dhcpd_conf: file=/tmp/dhcpd-br0.conf, ifname=br0, lan_ip=lan_ipaddr lan_mask=lan_netmask
cmd=[dhcpd -cf /tmp/dhcpd-br0.conf -lf /tmp/dhcpd.leases -df /tmp/udhcpd.leases -pf /var/run/dhcpd.pid br0 ]
Internet Systems Consortium DHCP Server 4.1.1-P1
Copyright 2004-2010 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
[Dnsmasq], fe800000000000004af8b3fffe16f5f1 is IFA_F_TENTATIVE, wait for 1 sec.
Wrote 0 leases to leases file.
Listening on Socket/br0/192.168.1.0/24
Sending on   Socket/br0/192.168.1.0/24
cmd=[upnp -D -W vlan2 ]
cmd=[/bin/eapd ]
UPnP::upnp_device_attach:br0: attach InternetGatewayDevice.xml
ssdp byebye
UPnP::upnp_init:UPnP daemon is ready to run
cmd=[nas ]
cmd=[killall wps_monitor ]
killall: wps_monitor: no process killed
waitpid: No child processes
cmd=[killall wps_ap ]
killall: wps_ap: no process killed
cmd=[killall wps_enr ]
killall: wps_enr: no process killed
cmd=[/bin/wps_monitor ]
cmd=[/usr/sbin/acsd ]
acsd: scan in progress ...
[Dnsmasq], socket AF_INET6: fe80::4af8:b3ff:fe16:f5f1, Interface-ID: 8
[Dnsmasq], socket AF_INET6: fec0::4af8:b3ff:fe16:f5f1, Interface-ID: 8
[Dnsmasq], socket AF_INET: 192.168.1.1
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x2b01
cmd=[netbios /tmp/samba/lib/netbios.conf ]
cmd=[nlinkd ]
lltd:echo Cisco38237 > /proc/sys/kernel/hostname
LLTD: wireless interface argument is eth1.
cmd=[killall -1 radvd ]
killall: radvd: no process killed
cmd=[/sbin/monitor_cable ]
cmd=[/usr/sbin/arp -c ]
cmd=[touch /tmp/hosts ]
tallest:=====( wan_or_lan=wan )=====
start_wan_ipv6: [IPV6] vlan2 dhcp-tunnel
cmd=[touch /tmp/hosts ]
waitpid: No child processes
dhcpc_main,reason[PREINIT]
start_wan_ipv6: [IPV6]  0
Hit enter to continue...cmd=[killall igmpxmld ]
killall: igmpxmld: no process killed
stop_dhcp6c
cmd=[/usr/sbin/ip -6 addr flush dev vlan2 scope global ]
cmd=[ip6tables -t filter -F ]
cmd=[ip6tables -t filter -Z ]
waitpid: No child processes
cmd=[ip6tables -t mangle -F ]
cmd=[ip6tables -t mangle -Z ]
Set 0 to /proc/sys/net/ipv6/conf/all/forwarding ...
ioctl: No such device
cmd=[killall -9 waninfo ]
stop_wan_ipv6: done
RTNETLINK answers: No such file or directory
cmd=[killall -9 qos_bw_detect ]
killall: qos_bw_detect: no process killed
cmd=[killall igmprt ]
killall: igmprt: no process killed
cmd=[killall pppoecd ]
killall: pppoecd: no process killed
cmd=[killall -9 pppoecd ]
killall: pppoecd: no process killed
cmd=[killall ip-up ]
killall: ip-up: no process killed
cmd=[killall ip-down ]
killall: ip-down: no process killed
cmd=[killall -15 pppd ]
killall: pppd: no process killed
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall -15 l2tpd ]
killall: l2tpd: no process killed
cmd=[killall -9 l2tpd ]
killall: l2tpd: no process killed
cmd=[killall -9 listen ]
killall: listen: no process killed
stop_dhcpc
cmd=[killall bpalogin ]
killall: bpalogin: no process killed
cmd=[killall -9 bpalogin ]
killall: bpalogin: no process killed
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall -9 pptp ]
killall: pptp: no process killed
cmd=[killall -9 listen ]
killall: listen: no process killed
cmd=[killall -9 ntpclient ]
killall: ntpclient: no process killed
cmd=[killall -9 redial ]
killall: redial: no process killed
cmd=[killall wan_auto_detect ]
killall: wan_auto_detect: no process killed
Hit enter to continue...


BusyBox v1.7.2 (2013-01-16 15:49:43 HKT) built-in shell (msh)
Enter 'help' for a list of built-in commands.

#
# cat ? /prioc   oc/cpuinfo
system type      : Broadcom BCMD144 chip rev 1
processor      : 0
cpu model      : MIPS 74K V4.9
BogoMIPS      : 149.50
wait instruction   : no
microsecond timers   : yes
tlb_entries      : 32
extra interrupt vector   : no
hardware watchpoint   : yes
ASEs implemented   : mips16 dsp
VCED exceptions      : not available
VCEI exceptions      : not available

unaligned_instructions   : 50
dcache hits      : 2147483648
dcache misses      : 4261100543
icache hits      : 2147483648
icache misses      : 4292870143
instructions      : 2147483648
# cat /proc/e memino fo
MemTotal:        28136 kB
MemFree:          3488 kB
Buffers:          2092 kB
Cached:           8032 kB
SwapCached:          0 kB
Active:           6592 kB
Inactive:         7492 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:        28136 kB
LowFree:          3488 kB
SwapTotal:           0 kB
SwapFree:            0 kB
Dirty:               0 kB
Writeback:           0 kB
AnonPages:        3968 kB
Mapped:           1936 kB
Slab:             7108 kB
SReclaimable:      532 kB
SUnreclaim:       6576 kB
PageTables:        420 kB
NFS_Unstable:        0 kB
Bounce:              0 kB
CommitLimit:     14068 kB
Committed_AS:     7664 kB
VmallocTotal:  1015800 kB
VmallocUsed:      2944 kB
VmallocChunk:  1010060 kB
# cat /proc/mtd
# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 00040000 00010000 "boot"
mtd1: 007b0000 00010000 "linux"
mtd2: 00660600 00010000 "rootfs"
mtd3: 00010000 00010000 "nvram"
#


Last edited by Fractal on Sun May 05, 2013 17:48; edited 2 times in total
Sponsor
smokinabowl
DD-WRT User


Joined: 21 Sep 2007
Posts: 370
Location: pittsburgh pa

PostPosted: Sat May 04, 2013 14:04    Post subject: Reply with quote
comments? i really hope belkin's product design and quality control doesnt have too much influence on the new linksys devices.
_________________
TP-Link TL-WR1043ND - DD-WRT std BS build 20675
WRT54GS v3/64mb ram/usb/sd mod - Tomato 1.28.0000 MIPS1 K26
WRT54G v5/16mb ram/usb/sd mod - DD-WRT mega BS build 14929
WAP54g v2/32mb ram/usb/sd mod - DD-WRT micro Eko Build 15943
WRTSL54GS sd mod - DD-WRT mini-usb Eko build 18946
Belkin N300 - DD-WRT std-usb-nas Eko build 16773M K2.6
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1187

PostPosted: Sat May 04, 2013 14:53    Post subject: Reply with quote
smokinabowl wrote:
comments? i really hope belkin's product design and quality control doesnt have too much influence on the new linksys devices.


To me so far it looks identical to the E900, however performance testing to be determined... I am going to get GPIO pulls and do some testing, this should be easy to get dd-wrt ported.. I got that router last night around midnight lol, and then had to go home and put it under the knife!.... Today the fun begins..

-Fractal
buddee
DD-WRT Guru


Joined: 06 Feb 2010
Posts: 7385
Location: Little Rock

PostPosted: Sat May 04, 2013 20:12    Post subject: Reply with quote
looks like an E900 but i would think its a 1x1 unit if its only a N150, the E900 does infact get N300.
_________________
Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ

Having problems with port forwarding? Check out Port Forward Troubleshooting for more info.
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1187

PostPosted: Sat May 04, 2013 20:34    Post subject: Reply with quote
buddee wrote:
looks like an E900 but i would think its a 1x1 unit if its only a N150, the E900 does infact get N300.


Correct, this is a 1x1 and the antenna is in the upper left side of the router... same specs 300mhz cpu, 32mb ram so not bad for 30$

-Fractal
buddee
DD-WRT Guru


Joined: 06 Feb 2010
Posts: 7385
Location: Little Rock

PostPosted: Sat May 04, 2013 22:02    Post subject: Reply with quote
Fractal wrote:
buddee wrote:
looks like an E900 but i would think its a 1x1 unit if its only a N150, the E900 does infact get N300.


Correct, this is a 1x1 and the antenna is in the upper left side of the router... same specs 300mhz cpu, 32mb ram so not bad for 30$

-Fractal


Which is rather strange due to this comparison chart, it specs it out to be a 1 antenna 2x2 unit, and pretty much matches the E900 specs aside from the 1 antenna arrangement. The 'strange' part to me is that in the specs comparison, they still rate it @ N300.

http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=22998

_________________
Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ

Having problems with port forwarding? Check out Port Forward Troubleshooting for more info.
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1187

PostPosted: Sun May 05, 2013 17:38    Post subject: E800 Ported DD-WRT Reply with quote
The E800 has been ported and tested!!! Please report any bugs here, I will submit patches to svn soon so we can get official support..

Enjoy GUYS!!!

Uploaded at Picoodle.com



dd-wrt.v24-21402_NEWD-2_K2.6_mini-e800.bin
 Description:

Download
 Filename:  dd-wrt.v24-21402_NEWD-2_K2.6_mini-e800.bin
 Filesize:  3.49 MB
 Downloaded:  1304 Time(s)

buddee
DD-WRT Guru


Joined: 06 Feb 2010
Posts: 7385
Location: Little Rock

PostPosted: Sun May 05, 2013 23:26    Post subject: Reply with quote
I don't have one of these units to test, but nonetheless, nice work Fractal and thanks for continuing to look into newer units getting ported!
_________________
Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ

Having problems with port forwarding? Check out Port Forward Troubleshooting for more info.
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1187

PostPosted: Wed May 08, 2013 2:50    Post subject: Reply with quote
looks like 7 downloads, any comments ??


ticket submitted for official support.

http://svn.dd-wrt.com:8000/ticket/2907


-Fractal
fisjer
DD-WRT Novice


Joined: 10 Jun 2013
Posts: 1

PostPosted: Mon Jun 10, 2013 18:49    Post subject: slow speeds? Reply with quote
I decided to try this one out, and have found (while it maybe specific to me...) that my internet speeds are a fraction of what they could be. I bypassed the router and got much faster speed tests (to the magnitude of 100x the speed).

Is there a good way to revert to the Linksys firmware?

Again, this could be specific to my setup or ignorance of best settings on dd-wrt.


*****
edit: I've found that when linked directly to my router the speed is very fast, but when connected over the wireless they are .01x the speed.
mrengles
DD-WRT User


Joined: 25 Feb 2010
Posts: 149
Location: United States

PostPosted: Fri Jul 19, 2013 12:09    Post subject: Reply with quote
Thanks Fractal for supporting this router. I'm using one of these to build a outdoor solar powered long range repeater with a nice 16dbi yagi.
mrengles
DD-WRT User


Joined: 25 Feb 2010
Posts: 149
Location: United States

PostPosted: Sat Jul 20, 2013 13:02    Post subject: Reply with quote
Here are some photos of my modified Cisco Linksys E800 with external RP-SMA for attaching external antennas.


image_132.jpg
 Description:
Feed line connector with RP-Male gold plated SMA.
 Filesize:  96.22 KB
 Viewed:  13355 Time(s)

image_132.jpg



image_800.jpg
 Description:
Feed line cable assembly with braided sleeving.
 Filesize:  128.91 KB
 Viewed:  13355 Time(s)

image_800.jpg


DasNeueReich
DD-WRT Novice


Joined: 29 Jul 2013
Posts: 1

PostPosted: Mon Jul 29, 2013 4:10    Post subject: Reply with quote
Hi,

I have a E800 bought from Walmart at the same price you mentioned. My problem is that the signal is not strong enough. I'm less then 4 feet from the router and the signal gets weak. Right now I'm in my bedroom, aprox 10ft, and I only have one sognal line.

I have an old belkin g that has strongest signal than this new one (full strength in my bedroom same 10ft from the router). I bought the e800 because the belkin started to "tilt" when I download files or do any big data transfer.

I'm very dissapointed first with myself, I blamed to me first (and then to the Cisco certifications I made a few years ago) because I think is something I'm missing. Now I'm not sure if this unit has a problem, or it is WAD (working as designed).

Is too late to change it for another one (I bought the unit more than 30 days ago) so I would really apreciate your comments about what may I do with this piece of router. Should I try to port it? Adding an external anthena sounds like a solution for my problem if it is really a signal related issue.


Sorry for the extention and sorry if this is not the proper thread to talk about this. I posted here because no other serious forums were found. The experience with Linksys support is something I dont want to mention... useless...

Thanks in advance.

Regards,

Claudio
Fitchburg, MA
mrengles
DD-WRT User


Joined: 25 Feb 2010
Posts: 149
Location: United States

PostPosted: Sat Aug 03, 2013 12:24    Post subject: Reply with quote
@DasNeueReich

I noticed when I opened up my router for the antenna mod, that the factory had very poor solder joints on the sheet metal antenna inside of the router itself.

Check the antenna feed line solder joints with a multimeter. Re solder if needed. My external yagi antenna is providing about 1/2 mile connection to another yagi.

The stock antenna on the router works fine, you probably have a defective unit.

Good luck,

Mrengles
dave_c
DD-WRT Novice


Joined: 19 Oct 2013
Posts: 1

PostPosted: Sat Oct 19, 2013 15:11    Post subject: Works like a charm Reply with quote
Downloaded and upgraded a new e800 last night... it works like a charm!

We need to add it to the list of 'Supported Devices'.
I almost passed this unit by while shopping for a replacement for a dead e1200 because it wasn't on the supported list (no 1200's in stock). The e800 in it's stock form was pretty lousy with 'n' cards, now it flies.

Thanks for porting/compiling it over!

Dave




Fractal wrote:
looks like 7 downloads, any comments ??


ticket submitted for official support.

http://svn.dd-wrt.com:8000/ticket/2907


-Fractal
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum