NeiroN
DD-WRT Novice
Joined: 27 Mar 2014
Posts: 1
|
 Posted: Thu Mar 27, 2014 10:52 Post subject: RT5350F Support |
 |
I have an another router on that chip
HKT-RM02
http://www.hlktech.net/product_detail.php?ProId=36
Does it possible to install dd-wrt?
Boot log
| Code: | U-Boot 1.1.3 (Jun 2 2011 - 15:02:04)
Board: Ralink APSoC DRAM: 16 MB
relocate_code Pointer at: 80fb4000
spi_wait_nsec: 42
spi device id: 7f 9d 46 7f 9d (9d467f9d)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
.*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.5.2.0
--------------------------------------------
Test by nicexie
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:Jun 2 2011 Time:15:02:04
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 360 MHZ ####
estimate memory size =16 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
my_tmp_test value is 400280
RT2880_GPIOMODE_REG is 400280
RT2880_GPIOMODE_REG is 40029c
RT2880_REG_PIODATA value is 32641
my_tmp value is 32641
0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
. Image Name: BL-MP01
Created: 2012-08-14 3:03:11 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 3784175 Bytes = 3.6 MB
Load Address: 80000000
Entry Point: 80253000
raspi_read: from:50040 len:39bdef
.......................................................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80253000) ...
## Giving linux memsize in MB, 16
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.21 (root@localhost.localdomain) (gcc version 3.4.2) #5 Tue Aug 14 11:03:05 HKT 2012
The CPU feqenuce set to 360 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Built 1 zonelists. Total pages: 4064
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 40808070, status = 11000000
PID hash table entries: 64 (order: 6, 256 bytes)
calculating r4koff... 0015f900(1440000)
CPU frequency 360.00 MHz
Using 180.000 MHz high precision timer.
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13652k/16384k available (2100k kernel code, 2732k reserved, 275k data, 116k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
deice id : 7f 9d 46 7f 9d (9d467f9d)
Warning: un-recognized chip ID, please update SPI driver!
EN25F32(1c 31161c31) (4096 Kbytes)
mtd .name = raspi, .size = 0x00400000 (4M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 7 MTD partitions on "raspi":
0x00000000-0x00400000 : "ALL"
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
0x00040000-0x00050000 : "Factory"
0x00050000-0x00114e2f : "Kernel"
mtd: partition "Kernel" doesn't end on an erase block -- force read-only
0x00114e2f-0x01000000 : "RootFS"
mtd: partition "RootFS" extends beyond the end of device "raspi" -- size truncated to 0x2eb1d1
mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
0x00050000-0x01000000 : "Kernel_RootFS"
mtd: partition "Kernel_RootFS" extends beyond the end of device "raspi" -- size truncated to 0x3b0000
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered (default)
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.7 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
rdm_major = 254
MAC_ADRH -- : 0x00000000
MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.0 256 rx/tx descriptors allocated, mtu = 1500!
MAC_ADRH -- : 0x00004802
MAC_ADRL -- : 0x2a80e814
PROC INIT OK!
IMQ starting with 2 devices...
IMQ driver loaded successfully.
Hooking IMQ after NAT on PREROUTING.
Hooking IMQ before NAT on POSTROUTING.
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.1
block2mtd: version $Revision: 1.1.1.1 $
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (128 buckets, 1024 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 116k freed
init started: BusyBox v1.12.1 (2012-08-14 10:52:31 HKT)
starting pid 13, tty '': '/etc_ro/rcS'
Algorithmics/MIPS FPU Emulator v1.5
devpts: called with bogus options
mount: mounting none on /proc/bus/usb failed: No such file or directory
Welcome to
_______ _______ ___ __ ____ _ _ ___
| ___ \| __ || | |__|| \ | || | / /
| |___| || |__| || |__ __ | \| || |/ /
| _ /| _ || || || |\ || \
|__| \__\|__| |__||______||__||_| \____||_|\___\
=System Architecture Department=
starting pid 22, tty '/dev/ttyS1': '/bin/sh'
BusyBox v1.12.1 (2012-08-14 10:52:31 HKT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
# internet.sh
Password for 'admin' changed
rmmod: cls: No such file or directory
rmmod: hw_nat: No such file or directory
rmmod: raeth: No such file or directory
insmod: bridge.ko: module not found
insmod: mii.ko: module not found
insmod: raeth.ko: module not found
phy_tx_ring = 0x00874000, tx_ring = 0xa0874000
phy_rx_ring0 = 0x00875000, rx_ring0 = 0xa0875000
RT305x_ESW: Link Status Changed
##### disable 1st wireless interface #####
rmmod: rt2860v2_ap_net: No such file or directory
rmmod: rt2860v2_ap: No such file or directory
rmmod: rt2860v2_ap_util: No such file or directory
rmmod: rt2860v2_sta_net: No such file or directory
rmmod: rt2860v2_sta: No such file or directory
rmmod: rt2860v2_sta_util: No such file or directory
Commit crc = 3453f7ba
insmod: rt2860v2_ap_util.ko: module not found
rt2860v2_ap: module license 'unspecified' taints kernel.
=== pAd = c004c000, size = 629120 ===
<-- RTMPAllocAdapterBlock, Status=0
insmod: rt2860v2_ap_net.ko: module not found
rmmod: nf_nat_pptp: No such file or directory
rmmod: nf_conntrack_pptp: No such file or directory
rmmod: nf_nat_proto_gre: No such file or directory
rmmod: nf_conntrack_proto_gre: No such file or directory
RX DESC a08a6000 size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
RTMP_TimerListAdd: add timer obj c00b6b80!
RTMP_TimerListAdd: add timer obj c0054014!
RTMP_TimerListAdd: add timer obj c0053be4!
RTMP_TimerListAdd: add timer obj c0053fc0!
RTMP_TimerListAdd: add timer obj c0053fe8!
RTMP_TimerListAdd: add timer obj c00540cc!
RTMP_TimerListAdd: add timer obj c00540f8!
RTMP_TimerListAdd: add timer obj c00542a4!
RTMP_TimerListAdd: add timer obj c00849bc!
RTMP_TimerListAdd: add timer obj c008458c!
RTMP_TimerListAdd: add timer obj c0084968!
RTMP_TimerListAdd: add timer obj c0084990!
RTMP_TimerListAdd: add timer obj c0084a74!
RTMP_TimerListAdd: add timer obj c0084aa0!
RTMP_TimerListAdd: add timer obj c00849e8!
RTMP_TimerListAdd: add timer obj c0084a14!
RTMP_TimerListAdd: add timer obj c0084a40!
RTMP_TimerListAdd: add timer obj c00b70a0!
RTMP_TimerListAdd: add timer obj c00b7078!
RTMP_TimerListAdd: add timer obj c00b7050!
RTMP_TimerListAdd: add timer obj c008d93c!
RTMP_TimerListAdd: add timer obj c008da40!
RTMP_TimerListAdd: add timer obj c008d964!
RTMP_TimerListAdd: add timer obj c0084f84!
RTMP_TimerListAdd: add timer obj c00514d8!
RTMP_TimerListAdd: add timer obj c0084ca4!
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
RTMP_TimerListAdd: add timer obj c00510dc!
RT305x_ESW: Link Status Changed
MCS Set = ff 00 00 00 01
SYNC - BBP R4 to 20MHz.l
RT305x_ESW: Link Status Changed
Main bssid = 48:02:2a:80:e8:14
<==== rt28xx_init, Status=0
0x1300 = 00064380
vconfig: ioctl error for rem: Invalid argument
vconfig: ioctl error for rem: Invalid argument
rmmod: 8021q: No such file or directory
insmod: 8021q.ko: module not found
eth2.2: Setting MAC address to 48 02 2a 80 e8 16.
device eth2 entered promiscuous mode
VLAN (eth2.2): Setting underlying device (eth2) to promiscious mode.
ifconfig: ioctl 0x8913 failed: No such device
brctl: bridge br0: No such device or address
device ra0 entered promiscuous mode
##### restore Ralink ESW to dump switch #####
switch reg write offset=14, value=5555
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1001
switch reg write offset=4c, value=1
switch reg write offset=50, value=2001
switch reg write offset=70, value=ffffffff
switch reg write offset=98, value=7f7f
switch reg write offset=e4, value=7f
done.
br0: port 2(eth2) entering learning state
br0: port 1(ra0) entering learning state
route: ioctl 0x890c failed: No such process
route: ioctl 0x890b failed: Network is unreachable
br0: port 2(eth2) entering disabled state
br0: port 1(ra0) entering disabled state
br0: port 2(eth2) entering learning state
br0: port 1(ra0) entering learning state
route: ioctl 0x890c failed: No such process
route: ioctl 0x890b failed: Network is unreachable
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
/sbin/lan.sh: line 63: hostname: not found
ifconfig: ioctl 0x8913 failed: No such device
Ralink APSoC Hardware Watchdog Timer
killall rt2860apd 1>/dev/null 2>&1
ntp.sh
ddns.sh
kill -9 `cat /var/run/wscd.pid.ra0`
cat: can't open '/var/run/wscd.pid.ra0': No such file or directory
kill: you need to specify whom to kill
iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
route delete 239.255.255.250 1>/dev/null 2>&1
killall -9 watchdog 1>/dev/null 2>&1
rmmod ralink_wdt.o
Stopped WatchDog Timer.
killall -q klogd
killall -q syslogd
syslogd -C8 1>/dev/null 2>&1
klogd 1>/dev/null 2>&1
killall -q zebra
killall -q ripd
channel_select.sh
iwpriv ra0 set Channel=1
Commit crc = 3453f7ba
webs: Listening for HTTP requests at address 192.168.16.254
br0: topology change detected, propagating
br0: port 2(eth2) entering forwarding state
br0: topology change detected, propagating
br0: port 1(ra0) entering forwarding state
|
|
|
