Posted: Fri May 23, 2014 14:46 Post subject: E3000 "slow" WAN
Hi,
My connection was recently upgraded and I now have 160/10 Mbps available.
However with DD-WRT it seems to be impossible to reach anything near this. I'm currently stuck at around 100Mbps.
Are there any tricks or firmware that I can use to speed this thing up?
I've tried original firmware and this gets me 160Mbps easy, but I need WOL (passtrough or webinterface) and this is not possible in original firmware of E3000.
I've messed around with a couple of firmware's but nothing helped much. With Tomato I got around 130 Mbps, but I would like to squeeze the last speed out of the connection. I also did not try K3.0 builds because it does seem difficult to flash (and possibly brick the router).
Joined: 24 Feb 2009 Posts: 2026 Location: Sol System > Earth > USA > Arkansas
Posted: Sat May 24, 2014 17:13 Post subject: Re: E3000 "slow" WAN
puijken wrote:
Hi,
My connection was recently upgraded and I now have 160/10 Mbps available.
However with DD-WRT it seems to be impossible to reach anything near this. I'm currently stuck at around 100Mbps.
Are there any tricks or firmware that I can use to speed this thing up?
I've tried original firmware and this gets me 160Mbps easy, but I need WOL (passtrough or webinterface) and this is not possible in original firmware of E3000.
I've messed around with a couple of firmware's but nothing helped much. With Tomato I got around 130 Mbps, but I would like to squeeze the last speed out of the connection. I also did not try K3.0 builds because it does seem difficult to flash (and possibly brick the router).
You might try "Kong's" firmware of the 22200 kind. It is still based on the 2.6 kernel, and is the last one (that I know of) that is optimized for speed.
As for WOL, I do not know if DD-WRT supports it. (It should, but I am not certain.) _________________ E3000 22200M KongVPN K26
WRT600n v1.1 refirb mega 18767 BS K24 NEWD2 [not used]
WRT54G v2 16214 BS K24 [access point]
Try Dropbox for syncing files - get 2.5gb online for free by signing up.
Read! Peacock thread
*PLEASE* upgrade PAST v24SP1 or no support.
Well, with DD-WRT my Asus RT-N16 reached no faster than 150 Mbps, with Tomato by Shibby no faster than 160 Mbps and with Asus Merlin is easily reaches 180 Mbps (that's my nominal bandwidth, so I cannot test higher speeds). All this without overclocking. From my experience I assume that an E3000 or E4200 will behave pretty much the same, except there is no Merlin firmware for it. Kong recommends an R7000, since it is future-proof.
Use Kong 22000+. _________________ 2 times APU2 Opnsense 21.1 with Sensei
2 times RT-AC56U running DD-WRT 45493 (one as Gateway, the other as AP, both bridged with LAN cable)
3 times Asus RT-N16 shelved
E4200 V1 running freshtomato 2020.8 (bridged with LAN cable)
3 times Linksys WRT610N V2 converted to E3000 and 1 original E3000 running freshtomato 2020.8 (bridged with LAN cable)
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Tue May 27, 2014 1:49 Post subject:
the cpu is too slow, stock fws in many routers use some "hacks"/hw nat if chip is present, to get high wan<->lan but ddwrt refuses to support such for technical reasons..my e3000(converted wrt610n v2) did 533mhz fine & the chip itself hardly got hot like most say e3000 do (unless there IS something different between native e3000 & wrt610n v2), according to broadcom the cpu is actually rated at 533mhz in the first place..if you dont want to oc it there isnt much to do besides replace it for a newer unit. _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers