[SOLVED] DIR-868L bricked need for help

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Author Message
leonanu
DD-WRT Novice


Joined: 15 Jun 2015
Posts: 22
Location: Beijing, China

PostPosted: Sat Jun 20, 2015 15:01    Post subject: [SOLVED] DIR-868L bricked need for help Reply with quote
Since I update my DIR-868L to 06-15-2015-r27297, my DIR-868L was bricked.

I've tried 30-30-30 reset many times, but didn't work.

After 30-30-30 reset, my DIR-868L got ping response by 192.168.1.1, and TTL=100. But.

1. There's seems no tftp exist. When I try to upload fireware by tftp(tftp -i 192.168.1.1 put xxxx.bin), I got a timeout error. And I try "telnet 192.168.1.1 69", also got timeout.

2. Thers's seems no factory web UI, open http://192.168.1.1, I got no response. Also I try "telnet 192.168.1.1 80", timeout too.

So, I've no idea to have my DIR-868L recovery.

Anyone could help me to get my DIR-868L back?


Last edited by leonanu on Sun Jun 21, 2015 15:01; edited 1 time in total
Sponsor
Malachi
DD-WRT Guru


Joined: 17 Jul 2012
Posts: 7209
Location: Columbus, Ohio

PostPosted: Sat Jun 20, 2015 15:13    Post subject: Reply with quote
Google d-link recovery room or emergency room.
_________________
I am far from a guru, I'm barely a novice.
Jerky_san
DD-WRT Novice


Joined: 15 Jun 2015
Posts: 14

PostPosted: Sat Jun 20, 2015 15:45    Post subject: Reply with quote
http://forums.dlink.com/index.php?topic=44909.0

Should mention IP matters.. what your computer is set to before the restart.. Like my R7000 there is someway of serving up a firmware image to it if my ip is 192.168.2.1 via a tftp server. It will only look for a tftp server on that ip and no other.
leonanu
DD-WRT Novice


Joined: 15 Jun 2015
Posts: 22
Location: Beijing, China

PostPosted: Sat Jun 20, 2015 15:48    Post subject: Reply with quote
Jerky_san wrote:
http://forums.dlink.com/index.php?topic=44909.0

Should mention IP matters.. what your computer is set to before the restart.. Like my R7000 there is someway of serving up a firmware image to it if my ip is 192.168.2.1 via a tftp server. It will only look for a tftp server on that ip and no other.


I can't visit the forums Crying or Very sad

For my DIR-868L, I've tried 192.168.2.1, no response. Only 192.168.1.1 could response.
Jerky_san
DD-WRT Novice


Joined: 15 Jun 2015
Posts: 14

PostPosted: Sat Jun 20, 2015 15:55    Post subject: Reply with quote
1. Plug the Ethernet cable that connects your computer, that was plugged into one of the LAN ports,
2. Setup your PC with static IP - ex: 192.168.0.2 (different from 192.168.0.1)
3. Make sure the PC has the new firmware
4. Unplug the power
5. Hold the reset button for 3~5 seconds and re plug the power WITHOUT RELEASING THE RESET BUTTON.
6.Open a web browser to 192.168.0.1 and then you should see EMERGENCY FLASHING page then click browse/upload locate the file and click UPLOAD FIRMWARE NOW

7. You should see a SUCCSESS page, If you don’t then re do steps 2-6
Matthew Hudson © 2010 All Rights Reserved
leonanu
DD-WRT Novice


Joined: 15 Jun 2015
Posts: 22
Location: Beijing, China

PostPosted: Sat Jun 20, 2015 16:01    Post subject: Reply with quote
Jerky_san wrote:
1. Plug the Ethernet cable that connects your computer, that was plugged into one of the LAN ports,
2. Setup your PC with static IP - ex: 192.168.0.2 (different from 192.168.0.1)
3. Make sure the PC has the new firmware
4. Unplug the power
5. Hold the reset button for 3~5 seconds and re plug the power WITHOUT RELEASING THE RESET BUTTON.
6.Open a web browser to 192.168.0.1 and then you should see EMERGENCY FLASHING page then click browse/upload locate the file and click UPLOAD FIRMWARE NOW

7. You should see a SUCCSESS page, If you don’t then re do steps 2-6
Matthew Hudson © 2010 All Rights Reserved


Thank you so much! I'll try again. Report later. Thank you !
leonanu
DD-WRT Novice


Joined: 15 Jun 2015
Posts: 22
Location: Beijing, China

PostPosted: Sun Jun 21, 2015 15:01    Post subject: Reply with quote
Jerky_san wrote:
1. Plug the Ethernet cable that connects your computer, that was plugged into one of the LAN ports,
2. Setup your PC with static IP - ex: 192.168.0.2 (different from 192.168.0.1)
3. Make sure the PC has the new firmware
4. Unplug the power
5. Hold the reset button for 3~5 seconds and re plug the power WITHOUT RELEASING THE RESET BUTTON.
6.Open a web browser to 192.168.0.1 and then you should see EMERGENCY FLASHING page then click browse/upload locate the file and click UPLOAD FIRMWARE NOW

7. You should see a SUCCSESS page, If you don’t then re do steps 2-6
Matthew Hudson © 2010 All Rights Reserved


That's working! My DIR-868L up again! Thank you so much!

It seems need clear IE cache before open Recovery Room web page, otherwise, it could be not able to open.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum