Author
Message
leoinacio DD-WRT Novice Joined: 24 Dec 2018 Posts: 13
Posted: Thu Dec 27, 2018 0:14 Post subject: CFE Console
Hi, my router is without IP in CFE console.
How can I set it?
The message : could not activate eth0 interface.
Back to top
Sponsor
leoinacio DD-WRT Novice Joined: 24 Dec 2018 Posts: 13
Posted: Thu Dec 27, 2018 13:31 Post subject:
Its possible to flash firmware from an USB device?
I can't use tftp if the router do not have an IP.
I think this has gone.
Back to top
SinCalChewy DD-WRT User Joined: 09 Nov 2014 Posts: 314 Location: Bakersfield, CA
Posted: Thu Dec 27, 2018 14:34 Post subject:
Read the Peacock Thread:
https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=51486
It has info on serial recovery. _________________
Deployed Routers:
Netgear R7800 - 1x build 46979
- Gateway (USB /w Entware, CAKE QoS)
Netgear R7000 - 3x build 46979
Back to top
leoinacio DD-WRT Novice Joined: 24 Dec 2018 Posts: 13
Posted: Thu Dec 27, 2018 15:33 Post subject:
Thank you, I read this, but i think then my router is dead.
I can navigate using wire.
Before, i put the dd-wrt on my router using serial cable, but i was trying make a ad-blocking and this results on kernel panic.
I flashed sotck FW using serial to recovery (with no errors on flash), but now web page only show login page and do not enter, and the bad notice, in serial console, the router do not have an ip anymore, i can't flash FW one more time, because it has no IP to tftp. (before, on startup, a LAN IP was attached)
Back to top
ian5142 DD-WRT Guru Joined: 23 Oct 2013 Posts: 2319 Location: Canada
Posted: Thu Dec 27, 2018 17:27 Post subject: Router Model
What Router Model?
JTAG and Serial are possibilities. _________________Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
Back to top
leoinacio DD-WRT Novice Joined: 24 Dec 2018 Posts: 13
Posted: Thu Dec 27, 2018 19:01 Post subject:
Linksys ea6200 ... Serial is possible,but
I think than an error in nvram that causes lan error. In cfe console, router has no ip.
Back to top
Per Yngve Berg DD-WRT Guru Joined: 13 Aug 2013 Posts: 6867 Location: Romerike, Norway
Posted: Thu Dec 27, 2018 20:15 Post subject:
Can't you do "nvram erase" at the CFE prompt?
Back to top
leoinacio DD-WRT Novice Joined: 24 Dec 2018 Posts: 13
Posted: Thu Dec 27, 2018 20:25 Post subject:
I do this nvram erase, but the problem was another.
Thank you guys. Since in CFE I did not have IP, I started trying all the commands, when I executed
devinfo set lan_addr = 192.168.1.1
my router came back to life.
it was very lucky, because I did not even know what I was doing, I was trying everything.
Thanks for ALL.
Back to top