ospitar DD-WRT Novice
Joined: 09 Jul 2007 Posts: 13
|
Posted: Tue Oct 02, 2012 9:40 Post subject: |
|
Don't know if anybody is still reading this thread, but it seems to be the most up to date for the TP-Link MR3420 router in HW-revision 1.x.
Last weekend I tried to get the device with two different 3G USB Huawei Modems working, but failed.
I installed latest Beta-firmware 07/20/12 (SVN revision: 19519) and attached a Huawei HiLink E353 (not branded) and a Huawei E352s-5 (German Telekom).
Both USB modems were not detected successfully. You can conclude a properly working device, if the status LED on the stick is not blinking, but running solidly. It was not possible to establish a 3G connection. When I tried to connect for several times manually, the router rebooted a few times.
Something must be wrong.
With latest original TP-Link Firmware everything is fine.
Both USB modems are detected successfully and running perfectly.
Following the guidance of unsupported mobile broadband modems, here is the output I got:
1. Huawei HiLink E353 (not branded)
Code: | dmesg
BusyBox v1.19.4 (2012-07-20 11:11:15 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
root@DD-WRT:~# dmesg
<5>[ 0.000000] Linux version 3.3.8-svn19518 (root@dd-wrt) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1530 Fri Jul 20 11:09:40 CEST 2012
<4>[ 0.000000] flash_size passed from bootloader = 4
<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 02000000 @ 00000000 (usable)
<4>[ 0.000000] Zone PFN ranges:
<4>[ 0.000000] Normal 0x00000000 -> 0x00002000
<4>[ 0.000000] Movable zone start PFN for each node
<4>[ 0.000000] Early memory PFN ranges
<4>[ 0.000000] 0: 0x00000000 -> 0x00002000
<7>[ 0.000000] On node 0 totalpages: 8192
<7>[ 0.000000] free_area_init_node: node 0, pgdat 80279060, node_mem_map 81000000
<7>[ 0.000000] Normal zone: 64 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
<4>[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
<4>[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
<6>[ 0.000000] Writing ErrCtl register=00000000
<6>[ 0.000000] Readback ErrCtl register=00000000
<6>[ 0.000000] Memory: 29480k/32768k available (2117k kernel code, 3288k reserved, 408k data, 164k init, 0k highmem)
<6>[ 0.000000] NR_IRQS:80
<6>[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
<6>[ 0.080000] pid_max: default: 32768 minimum: 301
<6>[ 0.080000] Mount-cache hash table entries: 512
<6>[ 0.090000] NET: Registered protocol family 16
<6>[ 0.130000] found calibration data for slot 0 on 0xBF3F1000
<4>[ 0.340000] registering PCI controller with io_map_base unset
<6>[ 0.360000] bio: create slab <bio-0> at 0
<6>[ 0.360000] PCI host bridge to bus 0000:00
<6>[ 0.370000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff]
<6>[ 0.370000] pci_bus 0000:00: root bus resource [io 0x0000]
<7>[ 0.380000] pci 0000:00:00.0: [168c:ff1c] type 0 class 0x000200
<6>[ 0.380000] pci 0000:00:00.0: fixup device configuration
<0>[ 0.380000] bootstrap returns device 168C:2E
<7>[ 0.390000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
<7>[ 0.390000] pci 0000:00:00.0: supports D1
<7>[ 0.390000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
<6>[ 0.390000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
<6>[ 0.390000] PCI: mapping irq 72 to pin1@0000:00:00.0
<6>[ 0.400000] Switching to clocksource MIPS
<6>[ 0.400000] NET: Registered protocol family 2
<6>[ 0.410000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.410000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
<6>[ 0.420000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.420000] TCP: Hash tables configured (established 1024 bind 1024)
<6>[ 0.430000] TCP reno registered
<6>[ 0.430000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.440000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.450000] NET: Registered protocol family 1
<7>[ 0.450000] PCI: CLS 0 bytes, default 32
<5>[ 0.450000] gpio_proc: module loaded and /proc/gpio/ created
<6>[ 0.460000] gpiochip_add: registered GPIOs 0 to 47 on device: ar71xx
<6>[ 0.460000] fixup WR741 Switch LED's
<5>[ 0.470000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<6>[ 0.470000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.480000] msgmni has been set to 57
<6>[ 0.480000] io scheduler noop registered
<6>[ 0.490000] io scheduler deadline registered (default)
<6>[ 0.490000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.520000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
<6>[ 0.530000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.540000] guessed flashsize = 4M
<0>[ 0.540000] scanning for root partition
<0>[ 0.550000] tplink uboot detected
<0>[ 0.550000] guessed bootloader size = 20000
<0>[ 0.560000]
<0>[ 0.560000] found squashfs at 100000
<5>[ 0.560000] Creating 8 MTD partitions on "ar7240-nor0":
<5>[ 0.570000] 0x000000000000-0x000000020000 : "RedBoot"
<5>[ 0.580000] 0x000000020000-0x0000003e0000 : "linux"
<5>[ 0.580000] 0x000000100000-0x0000003d0000 : "rootfs"
<5>[ 0.590000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.600000] 0x0000003d0000-0x0000003e0000 : "ddwrt"
<5>[ 0.600000] 0x0000003e0000-0x0000003f0000 : "nvram"
<5>[ 0.610000] 0x0000003f0000-0x000000400000 : "board_config"
<5>[ 0.620000] 0x000000000000-0x000000400000 : "fullflash"
<5>[ 0.620000] 0x000000000000-0x000000020000 : "fullboot"
<6>[ 0.630000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.640000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<6>[ 1.040000] PPP generic driver version 2.4.2
<6>[ 1.050000] PPP BSD Compression module registered
<6>[ 1.050000] PPP Deflate Compression module registered
<6>[ 1.060000] PPP MPPE Compression module registered
<6>[ 1.060000] NET: Registered protocol family 24
<6>[ 1.070000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout= 0)
<7>[ 1.080000] Registered led device: generic_0
<7>[ 1.080000] Registered led device: generic_1
<7>[ 1.080000] Registered led device: generic_2
<7>[ 1.080000] Registered led device: generic_3
<7>[ 1.080000] Registered led device: generic_4
<7>[ 1.080000] Registered led device: generic_5
<7>[ 1.080000] Registered led device: generic_6
<7>[ 1.080000] Registered led device: generic_7
<7>[ 1.080000] Registered led device: generic_8
<7>[ 1.080000] Registered led device: generic_9
<7>[ 1.080000] Registered led device: generic_10
<7>[ 1.080000] Registered led device: generic_11
<7>[ 1.080000] Registered led device: generic_12
<7>[ 1.080000] Registered led device: generic_13
<7>[ 1.080000] Registered led device: generic_14
<7>[ 1.080000] Registered led device: generic_15
<7>[ 1.080000] Registered led device: generic_16
<7>[ 1.080000] Registered led device: generic_17
<7>[ 1.080000] Registered led device: generic_18
<7>[ 1.080000] Registered led device: generic_19
<7>[ 1.080000] Registered led device: generic_20
<7>[ 1.080000] Registered led device: generic_21
<7>[ 1.080000] Registered led device: generic_22
<7>[ 1.080000] Registered led device: generic_23
<7>[ 1.080000] Registered led device: generic_24
<7>[ 1.090000] Registered led device: generic_25
<7>[ 1.090000] Registered led device: generic_26
<7>[ 1.090000] Registered led device: generic_27
<7>[ 1.090000] Registered led device: generic_28
<7>[ 1.090000] Registered led device: generic_29
<7>[ 1.090000] Registered led device: generic_30
<7>[ 1.090000] Registered led device: generic_31
<7>[ 1.090000] Registered led device: wireless_generic_0
<7>[ 1.090000] Registered led device: wireless_generic_1
<7>[ 1.090000] Registered led device: wireless_generic_2
<7>[ 1.090000] Registered led device: wireless_generic_3
<7>[ 1.090000] Registered led device: wireless_generic_4
<7>[ 1.090000] Registered led device: wireless_generic_5
<7>[ 1.090000] Registered led device: wireless_generic_6
<7>[ 1.090000] Registered led device: wireless_generic_7
<7>[ 1.090000] Registered led device: wireless_generic_8
<7>[ 1.090000] Registered led device: wireless_generic_9
<7>[ 1.090000] Registered led device: wireless_generic_10
<7>[ 1.090000] Registered led device: wireless_generic_11
<7>[ 1.090000] Registered led device: wireless_generic_12
<7>[ 1.090000] Registered led device: wireless_generic_13
<7>[ 1.090000] Registered led device: wireless_generic_14
<7>[ 1.090000] Registered led device: wireless_generic_15
<6>[ 1.090000] u32 classifier
<6>[ 1.100000] Performance counters on
<6>[ 1.100000] input device check on
<6>[ 1.100000] Actions configured
<6>[ 1.110000] Netfilter messages via NETLINK v0.30.
<6>[ 1.110000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
<4>[ 1.120000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 1.120000] nf_nat_rtsp v0.6.21 loading
<6>[ 1.130000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 1.130000] IPP2P v0.8.2 loading
<6>[ 1.130000] TCP westwood registered
<6>[ 1.140000] TCP hybla registered
<6>[ 1.140000] TCP vegas registered
<6>[ 1.140000] NET: Registered protocol family 17
<5>[ 1.150000] Bridge firewalling registered
<6>[ 1.150000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 1.160000] searching for nvram
<6>[ 1.160000] nvram size = 0
<6>[ 1.200000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 1.200000] Freeing unused kernel memory: 164k freed
<6>[ 4.240000] ag71xx_mdio: probed
<6>[ 4.240000] eth0: Atheros AG71xx at 0xb9000000, irq 4
<6>[ 4.840000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
<6>[ 4.850000] eth1: Atheros AG71xx at 0xba000000, irq 5
<6>[ 5.440000] eth1: Found an AR7240/AR9330 built-in switch
<6>[ 9.540000] Compat-wireless backport release: compat-wireless-2012-07-16
<6>[ 9.550000] Backport based on wireless-testing.git master-2012-07-16
<6>[ 9.550000] compat.git: wireless-testing.git
<6>[ 9.730000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 10.030000] cfg80211: World regulatory domain updated:
<6>[ 10.040000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 10.050000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.050000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.060000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.070000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.080000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<7>[ 10.420000] ath: EEPROM regdomain: 0x0
<7>[ 10.420000] ath: EEPROM indicates default country code should be used
<7>[ 10.420000] ath: doing EEPROM country->regdmn map search
<7>[ 10.420000] ath: country maps to regdmn code: 0x3a
<7>[ 10.420000] ath: Country alpha2 being used: US
<7>[ 10.420000] ath: Regpair used: 0x3a
<7>[ 10.430000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<7>[ 10.430000] Registered led device: ath9k-phy0
<6>[ 10.430000] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb0000000, irq=72
<6>[ 10.450000] cfg80211: Calling CRDA for country: US
<6>[ 10.550000] cfg80211: Regulatory domain changed to country: US
<6>[ 10.560000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 10.570000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 10.570000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 10.580000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.590000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.600000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.610000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<6>[ 10.920000] usbcore: registered new interface driver usbfs
<6>[ 10.930000] usbcore: registered new interface driver hub
<6>[ 10.940000] usbcore: registered new device driver usb
<6>[ 11.030000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 11.060000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 11.070000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<4>[ 11.080000] ehci_reset Intialize USB CONTROLLER in host mode: 3
<4>[ 11.090000] ehci_reset Port Status c000000
<6>[ 11.120000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 11.140000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<0>[ 11.140000] switch USB LED Off
<6>[ 11.140000] hub 1-0:1.0: USB hub found
<6>[ 11.150000] hub 1-0:1.0: 1 port detected
<6>[ 13.380000] device eth0 entered promiscuous mode
<0>[ 14.910000] switch USB LED On
<6>[ 14.910000] usb 1-1: new high-speed USB device number 2 using ar71xx-ehci
<6>[ 15.890000] device eth1 entered promiscuous mode
<6>[ 15.970000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 16.010000] cfg80211: World regulatory domain updated:
<6>[ 16.010000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 16.020000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.030000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.040000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.050000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.050000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.060000] cfg80211: Calling CRDA for country: US
<6>[ 16.080000] cfg80211: Regulatory domain changed to country: US
<6>[ 16.090000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 16.100000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 16.110000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 16.110000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.120000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.130000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.140000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<3>[ 20.130000] ath: phy0: Unable to set channel
<6>[ 23.440000] device ath0 entered promiscuous mode
<6>[ 23.450000] br0: port 3(ath0) entered forwarding state
<6>[ 23.450000] br0: port 3(ath0) entered forwarding state
<6>[ 25.250000] usbcore: registered new interface driver cdc_acm
<6>[ 25.250000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
<6>[ 25.360000] usbcore: registered new interface driver usbserial
<6>[ 25.360000] USB Serial support registered for generic
<6>[ 25.370000] usbcore: registered new interface driver usbserial_generic
<6>[ 25.370000] usbserial: USB Serial Driver core
<6>[ 25.450000] br0: port 3(ath0) entered forwarding state
<6>[ 25.500000] USB Serial support registered for Sierra USB modem
<6>[ 25.510000] usbcore: registered new interface driver sierra
<6>[ 25.510000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
<6>[ 25.560000] USB Serial support registered for GSM modem (1-port)
<6>[ 25.570000] usbcore: registered new interface driver option
<6>[ 25.570000] option: v0.7.2:USB Driver for GSM modems
<6>[ 26.910000] etherip: Ethernet over IPv4 tunneling driver
<6>[ 61.710000] eth1: link up (1000Mbps/Full duplex)
<6>[ 61.710000] br0: port 2(eth1) entered forwarding state
<6>[ 61.720000] br0: port 2(eth1) entered forwarding state
<6>[ 63.720000] br0: port 2(eth1) entered forwarding state
<6>[ 100.530000] eth1: link down
<6>[ 100.530000] br0: port 2(eth1) entered disabled state
<6>[ 583.030000] eth1: link up (1000Mbps/Full duplex)
<6>[ 583.030000] br0: port 2(eth1) entered forwarding state
<6>[ 583.040000] br0: port 2(eth1) entered forwarding state
<6>[ 585.040000] br0: port 2(eth1) entered forwarding state
root@DD-WRT:~# exit
|
Code: |
cat /proc/bus/usb/devices
cat /sys/kernel/debug/usb/devices
BusyBox v1.19.4 (2012-07-20 11:11:15 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
root@DD-WRT:~# cat /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8-svn19518 ehci_hcd
S: Product=Atheros AR91xx built-in EHCI controller
S: SerialNumber=platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1f01 Rev= 1.02
S: Manufacturer=HUAWEI
S: Product=HUAWEI HiLink
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
root@DD-WRT:~#
root@DD-WRT:~# cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8-svn19518 ehci_hcd
S: Product=Atheros AR91xx built-in EHCI controller
S: SerialNumber=platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1f01 Rev= 1.02
S: Manufacturer=HUAWEI
S: Product=HUAWEI HiLink
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
root@DD-WRT:~# exit
|
2. Huawei E352s-5 (German Telekom)
Code: | dmesg
BusyBox v1.19.4 (2012-07-20 11:11:15 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
root@DD-WRT:~# dmesg
0.080000] Mount-cache hash table entries: 512
<6>[ 0.090000] NET: Registered protocol family 16
<6>[ 0.130000] found calibration data for slot 0 on 0xBF3F1000
<4>[ 0.340000] registering PCI controller with io_map_base unset
<6>[ 0.360000] bio: create slab <bio-0> at 0
<6>[ 0.360000] PCI host bridge to bus 0000:00
<6>[ 0.370000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff]
<6>[ 0.370000] pci_bus 0000:00: root bus resource [io 0x0000]
<7>[ 0.380000] pci 0000:00:00.0: [168c:ff1c] type 0 class 0x000200
<6>[ 0.380000] pci 0000:00:00.0: fixup device configuration
<0>[ 0.380000] bootstrap returns device 168C:2E
<7>[ 0.390000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
<7>[ 0.390000] pci 0000:00:00.0: supports D1
<7>[ 0.390000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
<6>[ 0.390000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
<6>[ 0.390000] PCI: mapping irq 72 to pin1@0000:00:00.0
<6>[ 0.400000] Switching to clocksource MIPS
<6>[ 0.400000] NET: Registered protocol family 2
<6>[ 0.410000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.410000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
<6>[ 0.420000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.420000] TCP: Hash tables configured (established 1024 bind 1024)
<6>[ 0.430000] TCP reno registered
<6>[ 0.430000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.440000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.450000] NET: Registered protocol family 1
<7>[ 0.450000] PCI: CLS 0 bytes, default 32
<5>[ 0.450000] gpio_proc: module loaded and /proc/gpio/ created
<6>[ 0.460000] gpiochip_add: registered GPIOs 0 to 47 on device: ar71xx
<6>[ 0.460000] fixup WR741 Switch LED's
<5>[ 0.470000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<6>[ 0.470000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.480000] msgmni has been set to 57
<6>[ 0.480000] io scheduler noop registered
<6>[ 0.490000] io scheduler deadline registered (default)
<6>[ 0.490000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.520000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
<6>[ 0.530000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.540000] guessed flashsize = 4M
<0>[ 0.540000] scanning for root partition
<0>[ 0.550000] tplink uboot detected
<0>[ 0.550000] guessed bootloader size = 20000
<0>[ 0.560000]
<0>[ 0.560000] found squashfs at 100000
<5>[ 0.560000] Creating 8 MTD partitions on "ar7240-nor0":
<5>[ 0.570000] 0x000000000000-0x000000020000 : "RedBoot"
<5>[ 0.580000] 0x000000020000-0x0000003e0000 : "linux"
<5>[ 0.580000] 0x000000100000-0x0000003d0000 : "rootfs"
<5>[ 0.590000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.600000] 0x0000003d0000-0x0000003e0000 : "ddwrt"
<5>[ 0.600000] 0x0000003e0000-0x0000003f0000 : "nvram"
<5>[ 0.610000] 0x0000003f0000-0x000000400000 : "board_config"
<5>[ 0.620000] 0x000000000000-0x000000400000 : "fullflash"
<5>[ 0.620000] 0x000000000000-0x000000020000 : "fullboot"
<6>[ 0.630000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.640000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<6>[ 1.040000] PPP generic driver version 2.4.2
<6>[ 1.050000] PPP BSD Compression module registered
<6>[ 1.050000] PPP Deflate Compression module registered
<6>[ 1.060000] PPP MPPE Compression module registered
<6>[ 1.060000] NET: Registered protocol family 24
<6>[ 1.070000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout= 0)
<7>[ 1.080000] Registered led device: generic_0
<7>[ 1.080000] Registered led device: generic_1
<7>[ 1.080000] Registered led device: generic_2
<7>[ 1.080000] Registered led device: generic_3
<7>[ 1.080000] Registered led device: generic_4
<7>[ 1.080000] Registered led device: generic_5
<7>[ 1.080000] Registered led device: generic_6
<7>[ 1.080000] Registered led device: generic_7
<7>[ 1.080000] Registered led device: generic_8
<7>[ 1.080000] Registered led device: generic_9
<7>[ 1.080000] Registered led device: generic_10
<7>[ 1.080000] Registered led device: generic_11
<7>[ 1.080000] Registered led device: generic_12
<7>[ 1.080000] Registered led device: generic_13
<7>[ 1.080000] Registered led device: generic_14
<7>[ 1.080000] Registered led device: generic_15
<7>[ 1.080000] Registered led device: generic_16
<7>[ 1.080000] Registered led device: generic_17
<7>[ 1.080000] Registered led device: generic_18
<7>[ 1.080000] Registered led device: generic_19
<7>[ 1.080000] Registered led device: generic_20
<7>[ 1.080000] Registered led device: generic_21
<7>[ 1.080000] Registered led device: generic_22
<7>[ 1.080000] Registered led device: generic_23
<7>[ 1.080000] Registered led device: generic_24
<7>[ 1.090000] Registered led device: generic_25
<7>[ 1.090000] Registered led device: generic_26
<7>[ 1.090000] Registered led device: generic_27
<7>[ 1.090000] Registered led device: generic_28
<7>[ 1.090000] Registered led device: generic_29
<7>[ 1.090000] Registered led device: generic_30
<7>[ 1.090000] Registered led device: generic_31
<7>[ 1.090000] Registered led device: wireless_generic_0
<7>[ 1.090000] Registered led device: wireless_generic_1
<7>[ 1.090000] Registered led device: wireless_generic_2
<7>[ 1.090000] Registered led device: wireless_generic_3
<7>[ 1.090000] Registered led device: wireless_generic_4
<7>[ 1.090000] Registered led device: wireless_generic_5
<7>[ 1.090000] Registered led device: wireless_generic_6
<7>[ 1.090000] Registered led device: wireless_generic_7
<7>[ 1.090000] Registered led device: wireless_generic_8
<7>[ 1.090000] Registered led device: wireless_generic_9
<7>[ 1.090000] Registered led device: wireless_generic_10
<7>[ 1.090000] Registered led device: wireless_generic_11
<7>[ 1.090000] Registered led device: wireless_generic_12
<7>[ 1.090000] Registered led device: wireless_generic_13
<7>[ 1.090000] Registered led device: wireless_generic_14
<7>[ 1.090000] Registered led device: wireless_generic_15
<6>[ 1.090000] u32 classifier
<6>[ 1.100000] Performance counters on
<6>[ 1.100000] input device check on
<6>[ 1.100000] Actions configured
<6>[ 1.110000] Netfilter messages via NETLINK v0.30.
<6>[ 1.110000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
<4>[ 1.120000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 1.120000] nf_nat_rtsp v0.6.21 loading
<6>[ 1.130000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 1.130000] IPP2P v0.8.2 loading
<6>[ 1.130000] TCP westwood registered
<6>[ 1.140000] TCP hybla registered
<6>[ 1.140000] TCP vegas registered
<6>[ 1.140000] NET: Registered protocol family 17
<5>[ 1.150000] Bridge firewalling registered
<6>[ 1.150000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 1.160000] searching for nvram
<6>[ 1.160000] nvram size = 0
<6>[ 1.200000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 1.200000] Freeing unused kernel memory: 164k freed
<6>[ 4.240000] ag71xx_mdio: probed
<6>[ 4.240000] eth0: Atheros AG71xx at 0xb9000000, irq 4
<6>[ 4.840000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
<6>[ 4.850000] eth1: Atheros AG71xx at 0xba000000, irq 5
<6>[ 5.440000] eth1: Found an AR7240/AR9330 built-in switch
<6>[ 9.540000] Compat-wireless backport release: compat-wireless-2012-07-16
<6>[ 9.550000] Backport based on wireless-testing.git master-2012-07-16
<6>[ 9.550000] compat.git: wireless-testing.git
<6>[ 9.730000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 10.030000] cfg80211: World regulatory domain updated:
<6>[ 10.040000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 10.050000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.050000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.060000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.070000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.080000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<7>[ 10.420000] ath: EEPROM regdomain: 0x0
<7>[ 10.420000] ath: EEPROM indicates default country code should be used
<7>[ 10.420000] ath: doing EEPROM country->regdmn map search
<7>[ 10.420000] ath: country maps to regdmn code: 0x3a
<7>[ 10.420000] ath: Country alpha2 being used: US
<7>[ 10.420000] ath: Regpair used: 0x3a
<7>[ 10.430000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<7>[ 10.430000] Registered led device: ath9k-phy0
<6>[ 10.430000] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb0000000, irq=72
<6>[ 10.450000] cfg80211: Calling CRDA for country: US
<6>[ 10.550000] cfg80211: Regulatory domain changed to country: US
<6>[ 10.560000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 10.570000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 10.570000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 10.580000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.590000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.600000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.610000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<6>[ 10.920000] usbcore: registered new interface driver usbfs
<6>[ 10.930000] usbcore: registered new interface driver hub
<6>[ 10.940000] usbcore: registered new device driver usb
<6>[ 11.030000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 11.060000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 11.070000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<4>[ 11.080000] ehci_reset Intialize USB CONTROLLER in host mode: 3
<4>[ 11.090000] ehci_reset Port Status c000000
<6>[ 11.120000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 11.140000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<0>[ 11.140000] switch USB LED Off
<6>[ 11.140000] hub 1-0:1.0: USB hub found
<6>[ 11.150000] hub 1-0:1.0: 1 port detected
<6>[ 13.150000] eth1: link up (1000Mbps/Full duplex)
<6>[ 13.320000] device eth0 entered promiscuous mode
<6>[ 13.330000] eth1: link down
<0>[ 14.910000] switch USB LED On
<6>[ 14.910000] usb 1-1: new high-speed USB device number 2 using ar71xx-ehci
<6>[ 15.830000] device eth1 entered promiscuous mode
<6>[ 15.910000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 15.950000] cfg80211: World regulatory domain updated:
<6>[ 15.950000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 15.960000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 15.970000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 15.980000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 15.990000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 15.990000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.000000] cfg80211: Calling CRDA for country: US
<6>[ 16.020000] cfg80211: Regulatory domain changed to country: US
<6>[ 16.030000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 16.040000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 16.050000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 16.050000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.060000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.070000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 16.080000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<6>[ 16.640000] eth1: link up (1000Mbps/Full duplex)
<6>[ 16.640000] br0: port 2(eth1) entered forwarding state
<6>[ 16.650000] br0: port 2(eth1) entered forwarding state
<6>[ 18.650000] br0: port 2(eth1) entered forwarding state
<3>[ 20.010000] ath: phy0: Unable to set channel
<6>[ 23.320000] device ath0 entered promiscuous mode
<6>[ 23.330000] br0: port 3(ath0) entered forwarding state
<6>[ 23.330000] br0: port 3(ath0) entered forwarding state
<6>[ 25.140000] usbcore: registered new interface driver cdc_acm
<6>[ 25.140000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
<6>[ 25.290000] usbcore: registered new interface driver usbserial
<6>[ 25.300000] USB Serial support registered for generic
<6>[ 25.300000] usbcore: registered new interface driver usbserial_generic
<6>[ 25.310000] usbserial: USB Serial Driver core
<6>[ 25.330000] br0: port 3(ath0) entered forwarding state
<6>[ 25.480000] USB Serial support registered for Sierra USB modem
<6>[ 25.490000] usbcore: registered new interface driver sierra
<6>[ 25.490000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
<6>[ 25.540000] USB Serial support registered for GSM modem (1-port)
<6>[ 25.550000] usbcore: registered new interface driver option
<6>[ 25.550000] option: v0.7.2:USB Driver for GSM modems
<6>[ 26.860000] etherip: Ethernet over IPv4 tunneling driver
<6>[ 120.370000] device eth0 left promiscuous mode
<6>[ 120.380000] br0: port 1(eth0) entered disabled state
<6>[ 120.390000] device eth1 left promiscuous mode
<6>[ 120.400000] br0: port 2(eth1) entered disabled state
<6>[ 120.410000] device ath0 left promiscuous mode
<6>[ 120.410000] br0: port 3(ath0) entered disabled state
<6>[ 128.270000] device eth0 entered promiscuous mode
<6>[ 128.280000] eth1: link down
<6>[ 130.890000] device eth1 entered promiscuous mode
<6>[ 131.590000] eth1: link up (1000Mbps/Full duplex)
<6>[ 131.590000] br0: port 2(eth1) entered forwarding state
<6>[ 131.600000] br0: port 2(eth1) entered forwarding state
<6>[ 133.400000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 133.430000] cfg80211: World regulatory domain updated:
<6>[ 133.440000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 133.440000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 133.450000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 133.460000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 133.470000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 133.480000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 133.490000] cfg80211: Calling CRDA for country: US
<6>[ 133.510000] cfg80211: Regulatory domain changed to country: US
<6>[ 133.510000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 133.520000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 133.530000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 133.540000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 133.550000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 133.550000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 133.560000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<6>[ 133.600000] br0: port 2(eth1) entered forwarding state
<3>[ 137.560000] ath: phy0: Unable to set channel
<6>[ 140.500000] device ath0 entered promiscuous mode
<6>[ 140.510000] br0: port 3(ath0) entered forwarding state
<6>[ 140.510000] br0: port 3(ath0) entered forwarding state
<6>[ 142.510000] br0: port 3(ath0) entered forwarding state
root@DD-WRT:~# exit
|
Code: |
cat /proc/bus/usb/devices
cat /sys/kernel/debug/usb/devices
BusyBox v1.19.4 (2012-07-20 11:11:15 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
root@DD-WRT:~# cat /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 1/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8-svn19518 ehci_hcd
S: Product=Atheros AR91xx built-in EHCI controller
S: SerialNumber=platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1506 Rev= 1.02
S: Manufacturer=HUAWEI
S: Product=HUAWEI Mobile
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option
E: Ad=8f(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=(none)
E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I: If#= 1 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=(none)
E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0e(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=03 Driver=option
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0d(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=02 Driver=option
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
root@DD-WRT:~#
root@DD-WRT:~# cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 1/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8-svn19518 ehci_hcd
S: Product=Atheros AR91xx built-in EHCI controller
S: SerialNumber=platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1506 Rev= 1.02
S: Manufacturer=HUAWEI
S: Product=HUAWEI Mobile
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option
E: Ad=8f(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=(none)
E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I: If#= 1 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=(none)
E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0e(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=03 Driver=option
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0d(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=02 Driver=option
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
root@DD-WRT:~# exit
|
Hope anybody can help.
Maybe I should open a ticket on TRAC. What do you think?
Furthermore I would appreciate, if features like view of 3G radio, view of 2G/3G, connect on demand could be implemented.
I love the great DD-WRT project! |
|