[lantiq][danube][sx763] support request

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page 1, 2, 3, 4  Next
Author Message
vpritiskovic
DD-WRT User


Joined: 28 Aug 2009
Posts: 248
Location: Dalmatia, Croatia

PostPosted: Sat Dec 17, 2011 18:55    Post subject: [lantiq][danube][sx763] support request Reply with quote
Since there is initial support for lantiq - http://www.dd-wrt.com/site/content/first-adsl-router-with-dd-wrt-support it would be nice to have dd-wrt on this danube xway target.

HW highligts:
atheros WiFi / DSL port / 1 USB / 4 LAN ports / 32MB RAM / 8MB flash

HW detection already done:
http://wiki.openwrt.org/toh/gigaset/sx76x

Ready to donate the device/s to dev's

OpenWrt bootlog:
Code:
[    0.000000] Linux version 3.1.3 (bevandur@spalato) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #3 Sat Dec 3 10:56:51 CET 2011
[    0.000000] SoC: Danube rev 1.3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019641 (MIPS 24Kc)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 802894a0, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyLTQ1,115200 rootfstype=squashfs,jffs2 machtype=GIGASX76X
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=0002c138
[    0.000000] Readback ErrCtl register=0002c138
[    0.000000] Memory: 29560k/32768k available (2214k kernel code, 3208k reserved, 376k data, 168k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 333MHz
[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[    0.040000] pid_max: default: 32768 minimum: 301
[    0.044000] Mount-cache hash table entries: 512
[    0.052000] NET: Registered protocol family 16
[    0.064000] MIPS: machine is GIGASX76X - Gigaset SX761,SX762,SX763
[    0.080000] GIGASX76X: Found ethernet MAC address: 00:XX:XX:XX:XX:XX.
[    0.084000] GIGASX76X: Board id is sx763.
[    0.104000] bio: create slab <bio-0> at 0
[    0.112000] pci 0000:00:0e.0: [168c:ff16] type 0 class 0x000200
[    0.112000] pci 0000:00:0e.0: reg 10: [mem 0x00000000-0x0000ffff]
[    0.112000] pci 0000:00:0e.1: [168c:ff96] type 0 class 0x000700
[    0.112000] pci 0000:00:0e.1: reg 10: [io  0x0000-0x0007]
[    0.112000] pci 0000:00:0e.1: reg 14: [mem 0x00000000-0x00000fff]
[    0.112000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.116000] pci 0000:00:0e.0: BAR 0: set to [mem 0x18000000-0x1800ffff] (PCI address [0x18000000-0x1800ffff])
[    0.120000] pci 0000:00:0e.1: BAR 1: assigned [mem 0x18010000-0x18010fff]
[    0.124000] pci 0000:00:0e.1: BAR 1: set to [mem 0x18010000-0x18010fff] (PCI address [0x18010000-0x18010fff])
[    0.128000] pci 0000:00:0e.1: BAR 0: assigned [io  0x1ae00000-0x1ae00007]
[    0.132000] pci 0000:00:0e.1: BAR 0: set to [io  0x1ae00000-0x1ae00007] (PCI address [0x1ae00000-0x1ae00007])
[    0.136000] Switching to clocksource MIPS
[    0.144000] NET: Registered protocol family 2
[    0.148000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.156000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.164000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.172000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.176000] TCP reno registered
[    0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.192000] NET: Registered protocol family 1
[    0.196000] PCI: CLS 0 bytes, default 32
[    0.200000] gptu: totally 6 16-bit timers/counters
[    0.204000] gptu: misc_register on minor 63
[    0.208000] gptu: succeeded to request irq 126
[    0.212000] gptu: succeeded to request irq 127
[    0.216000] gptu: succeeded to request irq 128
[    0.220000] gptu: succeeded to request irq 129
[    0.224000] gptu: succeeded to request irq 130
[    0.232000] gptu: succeeded to request irq 131
[    0.240000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.244000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.256000] msgmni has been set to 57
[    0.260000] io scheduler noop registered
[    0.264000] io scheduler deadline registered (default)
[    0.268000] ltq_asc.0: ttyLTQ0 at MMIO 0x1e100400 (irq = 104) is a ltq_asc
[    0.276000] ltq_asc.1: ttyLTQ1 at MMIO 0x1e100c00 (irq = 112) is a ltq_asc
[    0.284000] console [ttyLTQ1] enabled, bootconsole disabled
[    0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001000
[    0.308000] ltq_nor: Found an alias at 0x800000 for the chip at 0x0
[    0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.312000]   Amd/Fujitsu Extended Query version 1.3.
[    0.316000] number of CFI chips: 1
[    0.320000] Creating 4 MTD partitions on "ltq_nor":
[    0.324000] 0x000000000000-0x000000010000 : "uboot"
[    0.332000] 0x000000010000-0x000000020000 : "uboot_env"
[    0.340000] 0x000000020000-0x0000007f0000 : "linux"
[    0.344000] Creating 2 MTD partitions on "ltq_nor":
[    0.348000] 0x000000020000-0x0000001066af : "kernel"
[    0.352000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.368000] 0x0000001066af-0x0000007f0000 : "rootfs"
[    0.372000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.388000] mtd: partition "rootfs" set to be root filesystem
[    0.392000] mtd: partition "rootfs_data" created automatically, ofs=440000, len=3B0000
[    0.400000] 0x000000440000-0x0000007f0000 : "rootfs_data"
[    0.408000] 0x0000007f0000-0x000000800000 : "board_config"
[    0.464000] ltq_mii: probed
[    0.464000] eth0: ADM6996M model PHY found.
[    0.472000] eth0: attached PHY [Infineon ADM6996] (phy_addr=0:00, irq=-1)
[    0.480000] Registered led device: soc:green:usb
[    0.480000] Registered led device: soc:green:wifi
[    0.480000] Registered led device: soc:green:phone2
[    0.484000] Registered led device: soc:green:phone1
[    0.484000] Registered led device: soc:green:line
[    0.484000] Registered led device: soc:green:online
[    0.484000] Registered led device: soc:green:voip
[    0.484000] TCP westwood registered
[    0.488000] NET: Registered protocol family 17
[    0.492000] 8021q: 802.1Q VLAN Support v1.8
[    0.512000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    0.520000] Freeing unused kernel memory: 168k freed
[    6.796000] JFFS2 notice: (452) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 6 of xref (0 dead, 2 orphan) found.
[    7.464000] SCSI subsystem initialized
[    7.656000] usbcore: registered new interface driver usbfs
[    7.660000] usbcore: registered new interface driver hub
[    7.672000] usbcore: registered new device driver usb
[    8.540000] Initializing USB Mass Storage driver...
[    8.544000] usbcore: registered new interface driver usb-storage
[    8.552000] USB Mass Storage support registered.
[   30.780000] Compat-wireless backport release: compat-wireless-2011-11-08-1-g4ab9b62
[   30.788000] Backport based on wireless-testing.git master-2011-11-15
[   31.020000] cfg80211: Calling CRDA to update world regulatory domain
[   31.724000] cfg80211: World regulatory domain updated:
[   31.728000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   31.736000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   31.744000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   31.752000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   31.760000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   31.768000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   32.568000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   32.572000] ath5k 0000:00:0e.0: registered as 'phy0'
[   32.580000] ath: EEPROM regdomain: 0x37
[   32.580000] ath: EEPROM indicates we should expect a direct regpair map
[   32.580000] ath: Country alpha2 being used: AW
[   32.580000] ath: Regpair used: 0x37
[   32.580000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   32.584000] ath5k phy0: Atheros AR2414 chip found (MAC: 0x79, PHY: 0x45)
[   32.592000] cfg80211: Calling CRDA for country: AW
[   32.648000] NET: Registered protocol family 8
[   32.648000] NET: Registered protocol family 20
[   32.716000] cfg80211: Regulatory domain changed to country: AW
[   32.720000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   32.728000] cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   32.736000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   32.744000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   32.752000] cfg80211:     (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[   32.772000] Button Hotplug driver version 0.4.1
[   33.232000] PPP generic driver version 2.4.2
[   33.568000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   33.852000] NET: Registered protocol family 24
[   33.996000] nf_conntrack version 0.5.0 (464 buckets, 1856 max)
[   34.612000] IFX MEI Version 5.00.00
[   34.780000]
[   34.780000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[   34.820000]     ATM (A1) firmware version 1.0.19
[   34.820000] ifxmips_atm: ATM init succeed
[   34.920000] dwc_otg: version 2.60a 22-NOV-2006
[   35.524000] DWC_otg: Using DMA mode
[   35.524000] dwc_otg dwc_otg.0: DWC OTG Controller
[   35.532000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
[   35.536000] dwc_otg dwc_otg.0: irq 62, io mem 0xffffffffbe101000
[   35.548000] DWC_otg: Init: Port Power? op_state=1
[   35.548000] DWC_otg: Init: Power Port (0)
[   35.556000] hub 1-0:1.0: USB hub found
[   35.556000] hub 1-0:1.0: 1 port detected
[   35.684000] usbcore: registered new interface driver ums-alauda
[   35.712000] usbcore: registered new interface driver ums-cypress
[   35.740000] usbcore: registered new interface driver ums-datafab
[   35.768000] usbcore: registered new interface driver ums-freecom
[   35.864000] usbcore: registered new interface driver ums-isd200
[   35.900000] usbcore: registered new interface driver ums-jumpshot
[   35.936000] usbcore: registered new interface driver ums-karma
[   35.952000] usb 1-1: new high speed USB device number 2 using dwc_otg
[   36.040000] usbcore: registered new interface driver ums-sddr09
[   36.076000] usbcore: registered new interface driver ums-sddr55
[   36.180000] usbcore: registered new interface driver ums-usbat
[   36.204000] scsi0 : usb-storage 1-1:1.0
[   36.296000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[   37.240000] scsi 0:0:0:0: Direct-Access              USB FLASH DRIVE  PMAP PQ: 0 ANSI: 0 CCS
[   37.264000] scsi: killing requests for dead queue
[   38.396000] scsi: killing requests for dead queue
[   38.404000] sd 0:0:0:0: [sda] 3915776 512-byte logical blocks: (2.00 GB/1.86 GiB)
[   38.416000] scsi: killing requests for dead queue
[   38.420000] sd 0:0:0:0: [sda] Write Protect is off
[   38.424000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[   38.424000] scsi: killing requests for dead queue
[   38.440000] sd 0:0:0:0: [sda] No Caching mode page present
[   38.444000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   38.452000] scsi: killing requests for dead queue
[   38.456000] scsi: killing requests for dead queue
[   38.472000] scsi: killing requests for dead queue
[   38.476000] scsi: killing requests for dead queue
[   38.492000] sd 0:0:0:0: [sda] No Caching mode page present
[   38.496000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   38.528000]  sda: sda1
[   38.540000] sd 0:0:0:0: [sda] No Caching mode page present
[   38.544000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   38.552000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   39.612000] device eth0.1 entered promiscuous mode
[   39.616000] device eth0 entered promiscuous mode
[   39.712000] br-lan: port 1(eth0.1) entering forwarding state
[   39.716000] br-lan: port 1(eth0.1) entering forwarding state
[   41.952000] cfg80211: Calling CRDA for country: HR
[   44.056000] device wlan0 entered promiscuous mode
[   44.060000] br-lan: port 2(wlan0) entering forwarding state
[   44.064000] br-lan: port 2(wlan0) entering forwarding state
[   45.104000] cfg80211: Calling CRDA to update world regulatory domain
[   47.052000] cfg80211: World regulatory domain updated:
[   47.056000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   47.064000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   47.072000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   47.080000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   47.088000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   47.096000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   47.104000] cfg80211: Calling CRDA for country: HR
[   47.360000] device wlan0 left promiscuous mode
[   47.360000] br-lan: port 2(wlan0) entering forwarding state
[   47.396000] cfg80211: Regulatory domain changed to country: HR
[   47.400000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   47.408000] cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   47.416000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   47.424000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   47.432000] cfg80211:     (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[   47.692000] device wlan0 entered promiscuous mode
[   47.696000] br-lan: port 2(wlan0) entering forwarding state
[   47.704000] br-lan: port 2(wlan0) entering forwarding state
[   49.644000] Trying 100/FULL
[  116.372000] [DSL_BSP_Showtime 916]: Datarate US intl = 319800, fast = 0

_________________
DD-WRT v24-sp2 (01/21/12) std - build 18613 @SX763
DD-WRT v24-sp2 (10/12/12) std - build 20119 @WZR-HP-G300NH (b0 b0)
Sponsor
zocra
DD-WRT Novice


Joined: 14 Jan 2007
Posts: 1

PostPosted: Sat Dec 17, 2011 19:15    Post subject: Reply with quote
It would be good to have the device with the ddwrt
oskreso
DD-WRT Novice


Joined: 17 Dec 2011
Posts: 11

PostPosted: Sat Dec 17, 2011 21:13    Post subject: SX763 Reply with quote
zocra wrote:
It would be good to have the device with the ddwrt


Man, I couldn't agree more. Can't wait to have dd-wrt developed for rhis hardware. I am willing to donate one piece or to test firmware.
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17442
Location: Hesse/Germany

PostPosted: Sat Dec 17, 2011 21:59    Post subject: Reply with quote
donate hw.

the buffalo was ported cause buffalo payed for it.

_________________
GEGEN die EEG-UMLAGE auf EIGENVERBRAUCH!
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
oskreso
DD-WRT Novice


Joined: 17 Dec 2011
Posts: 11

PostPosted: Sun Dec 18, 2011 12:17    Post subject: Reply with quote
Sash wrote:
donate hw.

the buffalo was ported cause buffalo payed for it.


To whom should I donate hardware?
DasShrubber2
DD-WRT User


Joined: 31 Oct 2011
Posts: 61

PostPosted: Sun Dec 18, 2011 19:38    Post subject: Reply with quote
Follow the instructions

http://www.dd-wrt.com/site/community/donations
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 6079
Location: Dresden, Germany

PostPosted: Thu Dec 22, 2011 11:46    Post subject: Reply with quote
as soon as i get it i will work on it. should be a easy task
_________________
one cigarette costs 2 minutes of your life.
one bottle of beer costs 4 minutes of your life.
one working day costs 8 hours of your life.

DD-WRT supported Concerts @ Bunker Dresden
03.10.2014 - Front 242 / Haujobb / Planet Myer Day
vpritiskovic
DD-WRT User


Joined: 28 Aug 2009
Posts: 248
Location: Dalmatia, Croatia

PostPosted: Thu Jan 05, 2012 13:52    Post subject: Reply with quote
BrainSlayer wrote:
as soon as i get it i will work on it. should be a easy task


Sent yesterday - usually the delivery take 10-15 working days...

_________________
DD-WRT v24-sp2 (01/21/12) std - build 18613 @SX763
DD-WRT v24-sp2 (10/12/12) std - build 20119 @WZR-HP-G300NH (b0 b0)
vpritiskovic
DD-WRT User


Joined: 28 Aug 2009
Posts: 248
Location: Dalmatia, Croatia

PostPosted: Sat Jan 14, 2012 14:01    Post subject: Reply with quote
Just wondering if the device has arrived?
_________________
DD-WRT v24-sp2 (01/21/12) std - build 18613 @SX763
DD-WRT v24-sp2 (10/12/12) std - build 20119 @WZR-HP-G300NH (b0 b0)
Revenger_HR
DD-WRT Novice


Joined: 18 Jan 2012
Posts: 9

PostPosted: Wed Jan 18, 2012 19:20    Post subject: Reply with quote
+1
I would like to see this happen very much!
Revenger_HR
DD-WRT Novice


Joined: 18 Jan 2012
Posts: 9

PostPosted: Thu Jan 19, 2012 12:39    Post subject: Reply with quote
BrainSlayer, did you get the device?
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17442
Location: Hesse/Germany

PostPosted: Thu Jan 19, 2012 13:53    Post subject: Reply with quote
vpritiskovic wrote:
Just wondering if the device has arrived?

yes. this week

_________________
GEGEN die EEG-UMLAGE auf EIGENVERBRAUCH!
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
Revenger_HR
DD-WRT Novice


Joined: 18 Jan 2012
Posts: 9

PostPosted: Thu Jan 19, 2012 16:41    Post subject: Reply with quote
niceee... when roughly can we expect first build?
vpritiskovic
DD-WRT User


Joined: 28 Aug 2009
Posts: 248
Location: Dalmatia, Croatia

PostPosted: Sat Jan 21, 2012 9:31    Post subject: Reply with quote
Snap from first testbuild, but it still has some issues with wifi, BS is alerted - should be fixed with next build.
_________________
DD-WRT v24-sp2 (01/21/12) std - build 18613 @SX763
DD-WRT v24-sp2 (10/12/12) std - build 20119 @WZR-HP-G300NH (b0 b0)
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 6079
Location: Dresden, Germany

PostPosted: Sat Jan 21, 2012 10:47    Post subject: Reply with quote
you got mail with additional fixes.
_________________
one cigarette costs 2 minutes of your life.
one bottle of beer costs 4 minutes of your life.
one working day costs 8 hours of your life.

DD-WRT supported Concerts @ Bunker Dresden
03.10.2014 - Front 242 / Haujobb / Planet Myer Day
Goto page 1, 2, 3, 4  Next Display posts from previous:    Page 1 of 4
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum