Assign WAN Port to Switch

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page Previous  1, 2
Author Message




Joined: 01 Jan 1970
Posts:

PostPosted: Sun Jul 15, 2012 21:26    Post subject: Reply with quote
The same problem here.
I can assing wan port to lan switch in GUI
Im using r19342
What sould i do?
Sponsor
Gradius
DD-WRT Novice


Joined: 11 May 2013
Posts: 23

PostPosted: Mon May 13, 2013 2:14    Post subject: Reply with quote
Sorry for bump, the problem is still present on 21286.

And confirmed...

I too need to do this:
Code:
swconfig dev rtl8366rb vlan 1 set ports '0 1 2 3 4 5t'
stopservice lan
startservice lan


In order to works (TP-Link TL-WR1043ND v1.6).
hildegarde321
DD-WRT Novice


Joined: 13 May 2013
Posts: 2

PostPosted: Mon May 13, 2013 8:59    Post subject: Reply with quote
We've set this particular inside my rc_firewall order, and it's functioning following a reboot. Devoid of the stop/start support, it does not function.

I examined this kind of by using a ping into a system on the regular interface, which usually worked well. Unplugging that and relocated this on the WAN interface halted the particular ping. Operating swconfig would not bring about called ping.
hardis
DD-WRT Novice


Joined: 05 Jul 2013
Posts: 4

PostPosted: Fri Jul 05, 2013 1:58    Post subject: Reply with quote
In my opinion,I think BrainSlayer really really forgot to implement reading switch configurtion nvram variables in the kernel and we have to do it by ourselves.
matcarfer
DD-WRT Novice


Joined: 27 Jan 2008
Posts: 7

PostPosted: Tue Mar 04, 2014 17:54    Post subject: Reply with quote
Gradius wrote:
Sorry for bump, the problem is still present on 21286.

And confirmed...

I too need to do this:
Code:
swconfig dev rtl8366rb vlan 1 set ports '0 1 2 3 4 5t'
stopservice lan
startservice lan


In order to works (TP-Link TL-WR1043ND v1.6).

I had the same problem and thanks to you its resolved. Thanks!
svenbr
DD-WRT Novice


Joined: 15 Sep 2014
Posts: 1

PostPosted: Mon Sep 15, 2014 10:59    Post subject: Reply with quote
Hi guys, thanks for the information so far and sorry for my bump as well. Running 21676 on a wr1043ND.

The trick to assign the wan port to the switch works for me as well, however I then loose my wireless connection to the router providing the internet connection.

my config:

Thomson wifi router connected to the internet
|| wireless (shared network)
TL - WR1043ND
|| wired (private network)
some computers

So I guess I should re-enable something else as well?

After I run commands:
swconfig dev rtl8366rb vlan 1 set ports '0 1 2 3 4 5t'
stopservice lan
startservice lan

I can connect to the ethernet (private network) using the WAN port. But when I run a DHCP release/renew under status -> wan it does not get an ip from the Thomson.

When I revert the port assignment by restarting the tp-link the connection to the wifi router re-establishes and I see correct ip config (obtained via DHCP) under status WAN. But of course I can't use the wan port for the private network...

Hopefully someone knows how to fix this? This config worked with an old firmware I was using before (I think even without running the commands but I'm not sure anymore).
Goto page Previous  1, 2 Display posts from previous:    Page 2 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum