Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29396_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
Router: RT-AC5300
Firmware: I will provide pictures explaining it:
Kernel: I will provide pictures explaining it:
Status: I will provide pictures explaining it:
Reset: Yes
Errors: No
Router: Linksys E4200 V1
Firmware: dd-wrt.v24-29396_NEWD-2_K3.x_mega-e4200.bin
Kernel: 3.10.101
Reset: no.
Errors: no.
Note: no USB device attached, use it as switch and AP.
Router: Linksys E3000 (formerly WRT610N V2)
Firmware: dd-wrt.v24-29396_NEWD-2_K3.x_mega-e3000.bin
Kernel: 3.10.101
Reset: no
Errors: no.
Note: use it as switch and AP. _________________ 2 times APU2 Opnsense 21.1 with Sensei
2 times RT-AC56U running DD-WRT 45493 (one as Gateway, the other as AP, both bridged with LAN cable)
3 times Asus RT-N16 shelved
E4200 V1 running freshtomato 2020.8 (bridged with LAN cable)
3 times Linksys WRT610N V2 converted to E3000 and 1 original E3000 running freshtomato 2020.8 (bridged with LAN cable)
Router: ASUS RT-AC66U
Firmware: DD-WRT v3.0-r29396 giga (04/04/16)
Kernel: Linux 3.10.101 #12111 Mon Apr 4 08:54:24 CEST 2016 mips
Status: Semi-working
Reset: Yes, before and after. telnet nvram clear, and webgui factory reset
Errors: The last two versions, I have had issues with the webgui becoming unresponsive. It times out completely for no reason. Never had this problem on previous versions.
Router: Asus RT-N18U
Firmware: DD-WRT v3.0-r29396 std (04/04/16)
Kernel: Linux 4.4.6 #569 Mon Apr 4 05:19:49 CEST 2016 armv7l
Status: Working
Reset: No (upgrade from 28882)
Errors: Site Survey does not work - no nearby networks are found (was same with 28882).
Question - is it normal there is no graphic bar indicating storage capacity under Services > USB?
My WDR4300 with Atheros chipset did display used/free space for attached USB storage devices.
Router: Buffalo wzr-1750dhp
Firmware: DD-WRT v3.0-r29396 std (04/04/16)
Kernel: 4.4.6 #565 SMP Mon Apr 4 05:06:33 CEST 2016 armv7l
Status: Working
Reset: yes
Previous: 29362\unbricked
Errors: On 5Ghz strange behavior - settings with lower lower 149 or upper upper 161 are go with weak signal, but auto settings is good signal.
AC/N-Mixed
SSID dd-wrt-5G
Channel 52 + 54
TX Power Auto
Rate 300 Mbps
Router: Asus RT-AC5300
Firmware: DD-WRT v3.0-r29396 std (04/04/16)
Kernel: Linux 4.4.6 #570 SMP Mon Apr 4 05:24:08 CEST 2016 armv7l
Status: Working ok
Previous: 29387
Reset: Hard reset, restore factory defaults by web gui, and hard reset again.
Errors:
Had to reboot router to get AES encryption working.
Second 5ghz radio has low signal strength.
LAN ethernet ports are still non-functional.
Internet connection light remains red. (internet still works) LED button doesn't turn off LEDs.
Router: RT-AC5300
Firmware: I will provide pictures explaining it:
Kernel: I will provide pictures explaining it:
Status: I will provide pictures explaining it:
Reset: Yes
Errors: No
I cant enter my router only with wireless, I think its broken
Try powering up the router while holding the wps button in till the power led flashes, then let it go and let it boot up. _________________ I am far from a guru, I'm barely a novice.
Last edited by Malachi on Mon Apr 04, 2016 23:11; edited 1 time in total
Router: TrendNet TEW-811DRU
Firmware: DD-WRT v3.0-r29396 mini (04/04/16)
Kernel: Linux 4.4.6 #568 Mon Apr 4 22:48:59 CEST 2016 armv7l
Status: semi working
Reset: flashed via webui, no reset, coming from 2015-24-12-r28598
Errors: webgui locks up within 15 mintes. All traffic stops since router locks up. Wan/wifi/lan all stops working.
Joined: 09 Nov 2014 Posts: 314 Location: Bakersfield, CA
Posted: Tue Apr 05, 2016 1:02 Post subject: Re: Any reason folders newer than 3/25/2016 are hidden
this build runs fine, though the throughput speed seems to have gone down a slight bit. Not getting the full full speed we pay for, but it's loading pages and stuff fine and fast. _________________ Deployed Routers:
Netgear R7800 - 1x build 46979
- Gateway (USB /w Entware, CAKE QoS)
Netgear R7000 - 3x build 46979
Posted: Tue Apr 05, 2016 1:04 Post subject: Re: Any reason folders newer than 3/25/2016 are hidden
Router: Buffalo WXR-1900DHP
Firmware: DD-WRT v3.0-r29396 std (04/04/16) from 03/31/2016 - r29387
Kernel: Linux 4.4.6 #565 SMP Mon Apr 4 05:06:33 CEST 2016 armv7l
Status: working
Reset: no
Errors: no
