thanks for your effort! it is really nice to know, that dd-wrt is working and that the modem is working too
i hope brainslayer provides a non-trial version soon. did you try to contact him directly? maybe he didn't recognize this thread and the other one in the german forum.
you should give it a try
besides that, thanks for sharing your device! i tried to access, but i alway get a timeout. tried it with https too, but it didn't work either.
ping is working fine though.
keep on the good work!
cheers iro _________________ E4200 running DD-WRT v24-sp2 vpnkong r20780M enhanced with OTRW Take2
Fritzbox 7170 as Gateway and for VOIP with Freetz 1.2 Stable
Thx for reply. I didn't contacted anyone, but i will now
About sharing my device web gui:
Maybe you could not login because i was loged in at the same time.
I had to unplug my easybox from the internet to check some settings regarding openwrt/dd-wrt/uboot. I still have some minor problems regarding boot console. Problem is it works ok in uboot, but as soon as the kernel gets uncompresed i lost output, just get some garbage symbols instead of nice bootlog. Yesterday i onece had full bootlog from dd-wrt but i got kernel panic. After that i changed uboot and it booted the kernel, but again garbage on serial console Problem is i dont know whitch uboot i used when bootlog was ok, as i tried dozen of them, some precompiled from openwrt some compiled myself. I am unsure if the problem is uboot or the kernel. If anyone knows how to fix this please tell.
heyhey,
any news? can't wait to get a non-trial version running on my device
cheers iro _________________ E4200 running DD-WRT v24-sp2 vpnkong r20780M enhanced with OTRW Take2
Fritzbox 7170 as Gateway and for VOIP with Freetz 1.2 Stable
trying to upload the dd-wrt to the 802nd EASYBOX but without success. router still resets
bootlog
Code:
ROM VER: 1.0.3
CFG 01
Readü
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X
U-Boot 2010.03 (Sep 08 2012 - 12:03:08)
Board: ARV752DPW
SoC: Danube/Twinpass/Vinax-VE V1.5, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 8 MB
*** Warning - bad CRC, using default environment
Net:
searching for rtl8306 switch ... found
Reset Hard
Done
Reset Soft
Success
lq_cpe_eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: DD-WRT v24 Linux Kernel Image
Created: 2012-07-20 10:14:36 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1054848 Bytes = 1 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.3.8-svn19518 (root@dd-wrt) (gcc version 4.6.3 201
20201 (prerelease) (Linaro GCC 4.6-2012.02) ) #107 Fri Jul 20 11:58:55 CEST 2012
[ 0.000000] SoC: Danube rev 1.5
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 16256
[ 0.000000] Kernel command line: console=ttyLTQ1,115200 root=1f03 rootfstype=
squashfs noinitrd machtype=ARV752DPW22 cp1_size=2M init=/sbin/init
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 byt
es
[ 0.000000] Writing ErrCtl register=0006fe28
[ 0.000000] Readback ErrCtl register=0006fe28
[ 0.000000] Memory: 61484k/65536k available (2477k kernel code, 4052k reserve
d, 512k data, 172k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=1105920)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 15 on device: ltq_gpio
[ 0.090000] gpiochip_add: registered GPIOs 16 to 31 on device: ltq_gpio
[ 0.090000] MIPS: machine is ARV752DPW22 - Arcor A803
[ 0.090000] gpiochip_add: registered GPIOs 100 to 115 on device: ltq_ebu
[ 0.090000] gpio_proc: module loaded and /proc/gpio/ created
[ 0.140000] bio: create slab <bio-0> at 0
[ 0.150000] PCI host bridge to bus 0000:00
[ 0.150000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.150000] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.150000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.150000] NET: Registered protocol family 8
[ 0.150000] NET: Registered protocol family 20
[ 0.150000] Switching to clocksource MIPS
[ 0.160000] NET: Registered protocol family 2
[ 0.160000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.160000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.160000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.160000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.160000] TCP reno registered
[ 0.160000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.160000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.160000] NET: Registered protocol family 1
[ 0.160000] gpio_proc: module loaded and /proc/gpio/ created
[ 0.160000] gptu: totally 6 16-bit timers/counters
[ 0.160000] gptu: misc_register on minor 62
[ 0.160000] gptu: succeeded to request irq 126
[ 0.160000] gptu: succeeded to request irq 127
[ 0.160000] gptu: succeeded to request irq 128
[ 0.160000] gptu: succeeded to request irq 129
[ 0.160000] gptu: succeeded to request irq 130
[ 0.160000] gptu: succeeded to request irq 131
[ 0.160000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[ 0.160000] msgmni has been set to 120
[ 0.170000] alg: No test for stdrng (krng)
[ 0.170000] io scheduler noop registered
[ 0.170000] io scheduler deadline registered (default)
[ 0.170000] ltq_asc.0: ttyLTQ0 at MMIO 0x1e100400 (irq = 104) is a ltq_asc
[ 0.170000] ltq_asc.1: ttyLTQ1 at MMIO 0x1e100c00 (irq = 112) is a ltq_asc
[ 0.500000] console [ttyLTQ1] enabled
[ 0.510000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer
ID 0x0000c2 Chip ID 0x0022cb
[ 0.520000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.530000] Amd/Fujitsu Extended Query version 1.1.
[ 0.530000] number of CFI chips: 1
[ 0.530000] parse_mtd returns 0
[ 0.540000] uImage size 1018C0
[ 0.540000] Creating 8 MTD partitions on "ltq_nor":
[ 0.540000] 0x000000000000-0x000000010000 : "uboot"
[ 0.550000] 0x000000010000-0x000000020000 : "uboot-env"
[ 0.560000] 0x000000020000-0x000000122000 : "kernel"
[ 0.560000] mtd: partition "kernel" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.580000] 0x000000122000-0x000000720000 : "rootfs"
[ 0.580000] mtd: partition "rootfs" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.600000] mtd: partition "rootfs" set to be root filesystem
[ 0.600000] 0x0000007d0000-0x0000007e0000 : "nvram"
[ 0.610000] 0x0000007f0000-0x000000800000 : "board_config"
[ 0.620000] 0x000000000000-0x000000800000 : "fullflash"
[ 0.620000] 0x000000720000-0x0000007d0000 : "ddwrt"
[ 0.630000] Creating 1 MTD partitions on "ltq_nor":
[ 0.630000] 0x000000020000-0x0000007d0000 : "linux"
[ 0.640000] tun: Universal TUN/TAP device driver, 1.6
[ 0.650000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.670000] ltq_mii: probed
[ 0.700000] Registering RTL8306SDM switch with Chip ID: 0x5988, version: 0x00
00
[ 0.700000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=ltq_etop-0:00, ir
q=-1)
[ 0.710000] PPP generic driver version 2.4.2
[ 0.720000] PPP BSD Compression module registered
[ 0.720000] PPP Deflate Compression module registered
[ 0.730000] PPP MPPE Compression module registered
[ 0.730000] NET: Registered protocol family 24
[ 0.750000] u32 classifier
[ 0.750000] Performance counters on
[ 0.750000] input device check on
[ 0.760000] Actions configured
[ 0.760000] Netfilter messages via NETLINK v0.30.
[ 0.770000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[ 0.770000] nf_conntrack_rtsp v0.6.21 loading
[ 0.780000] nf_nat_rtsp v0.6.21 loading
[ 0.780000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.780000] IPP2P v0.8.2 loading
[ 0.790000] TCP bic registered
[ 0.790000] TCP cubic registered
[ 0.790000] TCP westwood registered
[ 0.800000] TCP highspeed registered
[ 0.800000] TCP hybla registered
[ 0.800000] TCP htcp registered
[ 0.810000] TCP vegas registered
[ 0.810000] TCP veno registered
[ 0.810000] TCP scalable registered
[ 0.820000] TCP lp registered
[ 0.820000] TCP yeah registered
[ 0.820000] TCP illinois registered
[ 0.820000] NET: Registered protocol family 17
[ 0.830000] Bridge firewalling registered
[ 0.830000] 8021q: 802.1Q VLAN Support v1.8
[ 0.840000] searching for nvram
[ 0.840000] nvram size = 0
[ 0.980000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 0.990000] Freeing unused kernel memory: 172k freed
start service
starting Architecture code for danube
starting hotplug
Jan 1 00:00:03 udevtrigger[270]: parse_config_file: can't open '/etc/udev/udev.
conf' as config file: No such file or directory
done
ra0: No such device
[ 6.220000] IFX MEI Version 5.00.00
[ 6.410000] ATM (A1) firmware version 1.0.19
[ 6.410000] ifxmips_atm: ATM init succeed
[ 6.650000]
[ 6.650000]
[ 6.650000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[USB] checking...
[ 10.300000] device eth0 entered promiscuous mode
[ 10.300000] br0: port 1(eth0) entered forwarding state
[ 10.310000] br0: port 1(eth0) entered forwarding state
[ 11.430000] rt2860ap: module license 'unspecified' taints kernel.
[ 11.430000] Disabling lock debugging due to kernel taint
[ 11.450000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 11.570000] <=== RtmpAsicLoadFirmware (status=0)
[ 11.620000] read ralink eeprom from 410 with len 200 to 836f3828 (device 5)
[ 11.680000] 0x1300 = 00064380
[ 11.800000] <=== RtmpAsicLoadFirmware (status=0)
[ 11.890000] read ralink eeprom from 410 with len 200 to 836f3828 (device 5)
[ 11.930000] 0x1300 = 00064380
[ 12.070000] device ra0 entered promiscuous mode
[ 12.080000] br0: port 2(ra0) entered forwarding state
[ 12.080000] br0: port 2(ra0) entered forwarding state
ra0 no private ioctls.
ra0 no private ioctls.
[ 12.310000] br0: port 1(eth0) entered forwarding state
[ 14.080000] br0: port 2(ra0) entered forwarding state
br0: No such process
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
connect: Network is unreachable
connect: Network is unreachable
connect: Network is unreachable
gethostbyname: Network is unreachable
ra0: Operation not supported
erase[65536]
[ 17.020000] ltq_wdt: watchdog closed without warning
[ 25.760000] Restarting system.
some times at the end of bootlog i received information " Receiving restore command from resetbutton.
if anyone can help me?
2. Does modem and router both works well without any issues with above image? or does this device only works as router?
3. If dd-wrt image flashing works fine for you; do you have some information how to setup this device to behave only as router (i.e. to disable modem)?
Problem is i dont know whitch uboot i used when bootlog was ok, as i tried dozen of them, some precompiled from openwrt some compiled myself. I am unsure if the problem is uboot or the kernel. If anyone knows how to fix this please tell.
