[branconier]

hi, I can't download any of the latest ddwrt software, I think it's a problem with that, so if someone has one of the latest firmware for 615 H1, please send it to me via PM or on the e-mail at "my username"@yahoo.com
Thank you to all.

[ervau]

Are you not able to download from
ftp://ftp.dd-wrt.com/betas/2016/01-13-2016-r28788/
because you have no internet or are you not able to upgrade your H1?
ervau

[branconier]

No, I can not download anything, because when I open the link all I get are blank directories

[ervau]

To all the admins and gurus: is it ok to send him the files? I don't like to get in trouble with dd-wrt because of opening a "sharing platform". In the past I got a warning based on a similar topic.
ervau

[branconier]

ok, I know that it sounds unbelievable, but after I have updated the router firmware with r25697 (this was the latest that I could find and download), now I am able to see and download the latest r28788, I can't see the link between the update and the thing that now the link to the firmware really have content that I can see and download...
@ervau thank you for your concern and your attention.

[ervau]

You're welcome.
I can't see any link neither between installed FW and the ability of your browser to show the content of some INet site.
Anyway main issue: it works!

[wattie]

Just updated dir 615-h with r28846 - no problems.

[sitram]

Just updated Dlink DIR615h router with r28882 from the web interface without a factory reset. No problems so far.

[Alozaros]

ok so far so good just connected USB to TTL and this is the stock firmware D-link
output in puty, even if i try tpl + enter it asks for password and then goes on again this repeat on and on any ideas how to ??

http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288167

also do i need linux to tftp as im using Windows 7 currently

U-boot Ver:1.0.1.15 2011/05/05 13:28:21
Board: Ralink APSoC DRAM: 32 MB
============================================
ASIC 3352_MP (Port5<->None)
Product Name: DIR-615H1
SDRAM CAS = 3(d1835282)
============================================
Please choose the operation:
1: Load system code to SDRAM via TFTP.
Image Name: Linux Kernel Image
Created: 2012-09-04 2:13:25 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1109315 Bytes = 1.1 MB
Load Address: 80000000
Entry Point: 8023b000
OK

LINUX started...

THIS IS ASIC
init started: BusyBox v1.7.5 (2012-09-04 10:10:42 CST)
starting pid 137, tty '/dev/console': '/sbin/config_init'
Config Init version: 0.4.1.102 date: 2012/09/04
starting pid 191, tty '/dev/ttyS1': '/sbin/config_term'
************************************************************************
* DIR-615H1 *
************************************************************************
KernelApp/Ramdisk Ver:0.4.1.102 Date:2012/09/04
password: cat: can't open '/apps/lib/modules/2.6.21/modulesApp.dep': No such file or directory
ln: /sbin/./apps_init: File exists
ln: /sbin/./header: File exists
ln: /sbin/./opmode.sh: File exists
ln: /sbin/./reset: File exists
ln: /sbin/./udhcpd: File exists
ra0 no private ioctls.

[wattie]

04-25-2016-r29519 is the latest working version

All further versions up to the current (04-25-2016-r29519) are not OK.

[drou]

Hi, I found this old dir-615 and just tried to upgrade to 04-25-2016-r29519 but I cannot access the web interface. No matter what firmware I have chosen up until now, impossible to get the web interface (i change my static ip to 192.168.1.2). I can only access the firmware upgrade page (pressing reset, then connect to power). Do you think there is any chance to recover it or should I just through it to the recycling bin?

[ervau]

By pressing reset & repower the device you're in the emegency room; there I only was able to install D-Link firmware.
Power up the router press reset and try to reach the web interface with 192.168.0.1 or 1.1. According to that you have to set the ip of your pc.
Instaed of that procedure press reset for about 15sec. and than try the steps described above. Under Windows OS you can also try ipconfig /all (setting your pc to "get ip via DHCP") to find out the ip of the router.
In the past I couldn't find out any systematic. That's why I tried the steps described above.
Good luck.
ervau

[gradientByte]

Total novice here, just flashed r30260 trough the web interface. Works fine for now , just finished setting up wireless and internet. still have to do my port forwarding.

EDIT: and the vpn page is all white

[js1662]

Which file did you flash to your router? The dir615h-ddwrt-webflash.bin or the dlink-dir615h-factory-webflash.bin? If it is the dlink-dir615h-factory-webflash.bin, then upgrade the router again to dir615h-ddwrt-webflash.bin as it should at least has PPTP but not OpenVPN due to DIR615 version H has only 4M of flash.

[wattie]