Posted: Fri Aug 24, 2012 0:58 Post subject: Download Link?!
Where can i find the download link for DIR-615, Rev H1?
I see in the thread above a lot of people saying that they downloaded DD-WRT for H1, but i can't find any link to the firmware. The router database doesn't show any H1/H2.
Posted: Fri Aug 24, 2012 6:58 Post subject: Re: Download Link?!
atreidex wrote:
Where can i find the download link for DIR-615, Rev H1?
I see in the thread above a lot of people saying that they downloaded DD-WRT for H1, but i can't find any link to the firmware. The router database doesn't show any H1/H2.
Hi guys, does anyone know if the IPv6 that was supported by the original firmware of the H1, is any useful in terms of speed or stability??
Because I see that the dd-wrt firmware does not have an option for IPv6.
I tried everything:
- Flash factory: Upgrade failed
- Flash non factory: Upgrade failed
- Flash original dlink 803deb02 2012026: Upgrade failed
I am stuck with v24.sp2 06/08/12, can't upgrade my dir-615 H2.
Suggestions?
try dlink recovery mode: disconnect power, press and hold "reset" button, while holding "reset" connect power and hold "reset" for ~40 seconds (maybe not that long, but definitely more than 10 s, you'll see special unusual indication by LEDs), then release "reset". at this moment recovery mode web interface should be available at 192.168.0.1. connect to the router with an ethernet cable and upload, for example, original dlink firmware.
this recovery mode always works with my dlink dir-615H2, now flashed with 07/20/12 (SVN revision: 19519)
try dlink recovery mode: disconnect power, press and hold "reset" button, while holding "reset" connect power and hold "reset" for ~40 seconds (maybe not that long, but definitely more than 10 s, you'll see special unusual indication by LEDs), then release "reset". at this moment recovery mode web interface should be available at 192.168.0.1. connect to the router with an ethernet cable and upload, for example, original dlink firmware.
this recovery mode always works with my dlink dir-615H2, now flashed with 07/20/12 (SVN revision: 19519)
Thank you for your suggestion, I will try tonight or tomorrow
my DIR-615 H2 with the same dd-wrt (07/20/12) gives the same error for the last command (iwpriv ra0 set HtBssCoexApCntThr=10). no matter, after the first two commands on the wireless status page it says 300 mbit (150 before). i did not check the actual data rate as i dont have any 300-mbit capable client device.
Posted: Thu Sep 13, 2012 12:52 Post subject: Re: the command
4254 wrote:
]my DIR-615 H2 with the same dd-wrt (07/20/12) gives the same error for the last command (iwpriv ra0 set HtBssCoexApCntThr=10). no matter, after the first two commands on the wireless status page it says 300 mbit (150 before). i did not check the actual data rate as i dont have any 300-mbit capable client device.
So just skip the third command? =) I'll try that when i get home then I got 200mbit line so i can at least try to max that up.
try dlink recovery mode: disconnect power, press and hold "reset" button, while holding "reset" connect power and hold "reset" for ~40 seconds (maybe not that long, but definitely more than 10 s, you'll see special unusual indication by LEDs), then release "reset". at this moment recovery mode web interface should be available at 192.168.0.1. connect to the router with an ethernet cable and upload, for example, original dlink firmware.
this recovery mode always works with my dlink dir-615H2, now flashed with 07/20/12 (SVN revision: 19519)
It worked perfectly. I firs flashed original firmware, and after I was able to flash latest dd-wrt.
Posted: Sat Sep 15, 2012 10:11 Post subject: Help!!
I can't restore the original firmware, i have tried the 30/30/30 method but it just restory to factory default the dd-wrt firmware. What else can i do?
I have now installed the given DD-WRT from the factory DIR-615 H2 firmware and things seem to be fine.
BUT, under "Wireless Mode", the option "Client Bridge" is missing!
Since this is the option I need to use, and "Repeater Bridge" does not seem to work, I was wondering if this something missing from the "BrainSlayer" build?
Same here, and my gf who uses the wireless for a laptop is constantly complaining that she doesn't have internet ... Only the 2 commands didn't help. Reverted back to dlink firmware until fixed.